Cypress PU-515PL-KIT HDBaseT User manual

PU-515PL-KIT
HDBaseT™ LITE Extender Kit with PoE & 2-way IR (up to 60m)
OPERATION MANUAL

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.01 25/10/2013 First release

5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features..................................................7
6. Operation Controls and Functions .......8
6.1 Transmitter Front and Rear Panels....... 8
6.2 Receiver Front and Rear Panels ............ 9
6.3 D-Sub 9-Pin Denitions.........................10
6.4 IR Cable Pin Assignment .......................10
7. Connection Diagram .......................... 11
8. Specications...................................... 13
9. Acronyms............................................. 14

6
1. INTRODUCTION
The PU-515PL-KIT allows uncompressed HDMI signals to be transmitted
over a Single CAT5e/6/7 cable. This solution has the added features of RS-
232 and 2-way IR control, and Power over Ethernet (PoE) functionality
over the same CAT5e/6/7 cable. These combined HDMI and control
signals can be transmitted up to lengths of 60 metres.
2. APPLICATIONS
Domestic HDMI installations
University lecturing systems
Retail showroom systems
Conference presentation and control
3. PACKAGE CONTENTS
1×HDMI over Single CAT5e/6/7 Transmitter with PoE
1×HDMI over Single CAT5e/6/7 Receiver with PoE
1×IR Blaster
1×IR Extender
1×3.5 mm Mini-jack to RS-232 Female Cable
1×3.5 mm Mini-jack to RS-232 Male Cable
24 V/1.25 A DC Power Adaptor
Operation Manual
4. SYSTEM REQUIREMENTS
HDMI source equipment such as a DVD or Blu-ray player and HDMI
equipped display (TV or monitor). HDMI and CAT5e/5/7 connection
cables.

7
5. FEATURES
HDMI 1.4 with 3D, 4K×2K support, HDCP and DVI compliant
Supports HDMI 1.4 (including HDCP) over a single CAT5e/6/7 up to 60m
Complies with HDBaseT™- Lite specications
Full HD resolution support (1080p@60Hz/36-bit), 3D over 60m, 4Kx2K over
40m and PC resolution support (VGA to WUXGA) over CAT5e/6 cable
HDMI input up to 15m with 8-bit deep colour, or 10m with 12-bit deep colour
Supports HDMI output up to 15m with 8/12-bit deep colour
Supports two-way IR, RS-232 Control, and Power Over Ethernet (PoE)
Installation friendly
Note
1. This system was tested with CAT-6E/23AWG cables, results may vary with
cables of a dierent specication.
2. The PoE function is designed for powering compatible receiver units
only—do not use with non-PoE receivers or receivers of another brand.

8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
Power
Link
CAT 5e /6/7 Out
IR2 Extender
RS-232 In IR1 Blaster
HDMI In
Transmitter
1 2 3 4 5 6 7 8
1
RS232 In: Connect to a PC/laptop or RS-232 control device (with
supplied 3.5 mm mini-jack to D-sub 9-pin adaptor) for the transmission
of RS-232 commands.
2
IR2 Extender: Connect an IR extender cable for IR signal reception.
Ensure that remote control being used is within the direct line-of-
sight of the IR extender.
3
IR1 Blaster: Connect an IR blaster cable for IR signal transmission.
Place the IR blaster in direct line-of-sight of the equipment to be
controlled.
4
HDMI In: Connect to the HDMI source equipment such as a DVD or
Blu-ray player.
5
DC 24V: Connect the 24V DC power supply to the unit and plug the
adaptor into an AC outlet.
6
Link LED: The yellow LED will illuminate when both the input and
output CAT5e/6/7 signals are connected. The LED will blink when
there is an error with the transmission signal.
7
Power LED: This green LED will illuminate when the device is
connected to a power supply.
8
CAT5e/6 Out: Connect to the receiver unit with a single CAT5e/6/7
cable for transmission of all data signals.

9
6.2 Receiver Front and Rear Panels
Power
Link
CAT 5e /6/7 In
IR1 Extender
RS-232 Out IR2 Blaster
HDMI Out
Receiver
2 3 4 5 6 71
1
RS232 Out: Connect to the device that is to be controlled (with
the supplied 3.5mm mini-jack to D-sub 9-pin adaptor) by RS-232
commands
2
IR1 Extender: Connect an IR extender cable for IR signal reception.
Ensure that the remote being used is within the direct line-of-sight of
the IR extender.
3
IR2 Blaster: Connect an IR blaster cable for IR signal transmission.
Place the IR blaster in direct line of sight of the equipment to be
controlled.
4
HDMI Out: Connect to a HDMI equipped TV/monitor for display of the
HDMI input source signal.
5
Link LED: This yellow LED will illuminate when both the input and
output CAT5e/6/7 signals are connected. The LED will blink when
there is an error with the transmission signal.
6
Power LED: This green LED will illuminate when the device is
connected to a power supply.
7
CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6/7
cable for transmission of all data signals.

10
6.3 D-Sub 9-Pin Denitions
PIN DEFINE TX/RX
1N/C
2TxD/RxD
3RxD/TxD
4N/C
5GND
6N/C
7N/C
8N/C
9N/C
6.4 IR Cable Pin Assignment
3
1
3
1
2
2
Power 5V
IR Blaster Signal
NC
IR Signal
Power 5V
Ground
IR Extender
IR Blaster

11
7. CONNECTION DIAGRAM
Example 1: Direct Connection
Power
Link
CAT 5e/6/7 In
IR1 Extender
RS-232 Out IR2 Blaster
HDMI Out
Receiver
Power
Link
CAT 5e/6/7 Out
IR2 Extender
RS-232 In IR1 Blaster
HDMI In
Transmitter
1.5m
60°
7m
3m 3m
60°
m
1.5m
60°
7m
3m
3m
60°
m
DVD or Blu-ray Player
Display
Single
CAT5e/6/7
Cable (60 m)
Receiver powered
over CAT Cable by
PoE
Power
Supply
RS-232 Equipped Device
to be controlled
RS-232
Equipped PC or
Notebook
IR Extender
IR Extender
IR Blaster
IR Blaster
RS-232
Adaptor
RS-232
Adaptor
TX
RX
HDMI
Output
HDMI
Input

12
Example 2: Using a Repeater to Extend the Operating Distance
Power
Link
CAT 5e /6/7 Out
IR2 Extender
RS-232 In IR1 Blaster
HDMI In
Transmitter
Power
Link
CAT 5e/6/7 In
IR1 Extender
RS-232 Out IR2 Blaster
HDMI Out
Receiver
7m3m 3m
60°
m
m
m
1.5m
60°
CAT5e/6 OUT
MODE LINK
DC 24V
CAT5e/6 IN
POWER
MODELINK
1.5m
60°
7m
3m 3m
60°
m
Optional
HDBaseT Lite
Repeater
Blu-ray Player
HDMI
Input
HDMI
Output
IR Blaster
IR Blaster
RS-232
Equipped PC
or Control
System
IR Extender
IR Extender
HDTV
Power
Supply
Power
Supply
RS-232 Device to
be Controlled
TX
Rear
Front
RX
Single
CAT5e/6/7
Cable (60 m)
Single
CAT5e/6/7
Cable (60 m)
RS-232
Adaptor
RS-232
Adaptor

13
8. SPECIFICATIONS
Video Bandwidth 300 MHz/10.2 Gbps
Transmitter
Input Ports 1×HDMI, 1×IR Extender, 1×RS-232
Output Ports 1×CAT5e/6/7, 1×IR Blaster
Receiver
Input Ports 1×CAT5e/6/7, 1×IR Extender
Output Ports 1×HDMI, 1×IR Blaster, 1×RS-232
CAT5e/6/7 Cable
Distance
Up to 60 meters
HDMI Input Cable
Distance
15 meters/8-bit, 10 meters/12-bit
HDMI Output Cable
Distance
15 meters/8-bit, 10 meters/12-bit
ESD Protection Human Body Model:
±8 kV (air-gap discharge)
±4 kV (contact discharge)
Power Supply 24 V/1.25 A DC (US/EU standards, CE/
FCC/UL certied)
Dimensions 71 mm (W)×79 mm(D)×23 mm (H)/Each
Weight 120 g/TX, 126 g/RX
Chassis Material Metal
Colour Black
Operating Temperature 0 ˚C ~ 40 ˚C / 32 ˚F ~ 104 ˚F
Storage Temperature −20 ˚C ~ 60 ˚C / −4 ˚F ~ 140 ˚F
Relative Humidity 20 ~ 90% RH (non-condensing)
Power Consumption 3 W/TX, 6 W/RX

CAT5e/6/7 Cable Specication:
LENGTH BAND
WIDTH
DATA
RATE
SUPPORTED VIDEO
UP TO
60 M
UP TO
225 MHZ
UP TO
5.3 GBPS
HD VIDEO
UP TO 1080P@60 HZ/36-BIT, 3D
(DATA RATE LOWER THAN 5.3
GBPS OR BANDWIDTH BELOW
225 MHZ).
UP TO
35 M
GREATER
THAN
225 MHZ
GREATER
THAN
5.3 GBPS
ULTRA HD VIDEO
UP TO 4K×2K@30 HZ.
9. ACRONYMS
ACRONYM COMPLETE TERM
CAT5e Category 5 Cable
CAT6 Category 6 Cable
CAT7 Category 7 Cable
CEC Consumer Electronics Control
DVI Digital Visual Interface
HDCP High-bandwidth Digital Content Protection
HDMI High-Denition multimedia Interface
IR Infrared
PoE Power over Ethernet

CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton,
Middlesex, TW17 8BA
Tel: [phone] | Fax: [phone]
Email: [email protected]
www.cypeurope.com
v1.01