Cypress CMSI-8H8HS User manual

CMSI-8H8HS
8×8 HDMI Matrix
Operation Manual
Operation Manual

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 11/11/11 Preliminary Release
RDV2 13/12/11 Power Supply Change
RDV3 15/02/12 LAN Function
VS0 29/03/12 Updated format, diagrams, and
statements
RDV4 04/07/12 Control's Function
VS0 24/07/12 Telnet and Web GUI sections
updated

CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel.........................................4
6.3 Side Panel .........................................5
6.4 Remote Control................................5
6.5 RS-232 Pin Assignment .....................6
6.6 RS-232 and Telnet Commands .......7
6.7 Telnet Control ...................................8
7. Connection Diagram .......................... 10
8. Specications ...................................... 11
9. Acronyms ............................................. 12

1
1. INTRODUCTION
The 8×8 HDMI Matrix supports the transmission of Video (up to 1080p
Full HD/1920×1200@60 Hz) with multichannel digital audio from up to
eight high denition sources to up to eight HDMI outputs and allowing
any source to be independently displayed on any monitor. Also, the
unit can be controlled via IR, RS-232, Telnet or the front panel button
controls.
2. APPLICATIONS
• Video/TV wall display
• Commercial advertising and display
• Lecture room display and control
• Hyper market demonstration and control
3. PACKAGE CONTENTS
• 8×8 HDMI Matrix
• 1×24 V/6.25 A DC Adaptor
• 1×Remote Control
• 1xIR Extender
• Operation Manual
4. SYSTEM REQUIREMENTS
• HDMI equipped input source devices with HDMI cables
• HDMI equipped output displays (TVs or monitors) or HDMI equipped
AV receivers with HDMI cables

2
5. FEATURES
• HDMI, HDCP 1.1 and DVI compliant
• Supports HDMI features including 3D
• Supports audio sampling rate up to 192 kHz
• Supports resolutions VGA~WUXGA and 480i~1080p dependent upon
the output display’s EDID settings
• Supports 3D signal display dependent upon the output display's
EDID settings
• Supports HDMI input up to 15 meters at 8-bit resolution or 10 meters
at 12-bit resolution and HDMI output up to 15 meters at 8-bit/12-bit
• Supports IR extension
• Supports RS-232, remote control, on-panel control and IP Control
(Telnet)
• 2U size design

3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER LOCK
MENU OUTA 1B2C3D4
IN
E5F6G7H8
8X8 HDMI MATRIX CMSI-8H8HS
2 3 4 5 61
1
LCM:Displays the setting information of each input and output
setting.
2
POWER: Press this button to power the device on/off. The LED will
illuminate green when the power is on, red when it is in 'Standby'
mode.
3
LOCK: Press this button to lock all the buttons on the panel; press
again to unlock. The LED will illuminate green when locked.
4
IR: IR Receiver window (accepts the remote control signal of this
device only).
5
MENU: Press this button to access the LCM menu system, from
here EDID settings can be managed and IP system settings are
displayed.
Note: For the 'TV' EDID setting, the unit will read and store the
EDID information of the display connected to HDMI output A. For
the 'STD' EDID setting the unit's built-in EDID setting will be used
(1080p@60/12-bit for video and LPCM 2CH for audio).
6
1~8/A~H and OUT/IN: Press the OUT or IN button to select the
output or input mode and then press the required number button
to make the selection accordingly.
For example, if outputs A~D need to be set to input 1 and outputs
E~H need to be set to input 2 then the following sequence of
button presses need to be performed:
Press: OUTABCDIN1MENU,
and then press: OUTEFGHIN2MENU.
Note: If the MENU button is not pressed the selection will not be
changed.

4
6.2 Rear Panel
CONTROL
DC 24V
IR-In
RS-232 Service
A
HDMI Out
1
HDMI In
B
HDMI Out
2
HDMI In
C
HDMI Out
3
HDMI In
D
HDMI Out
4
HDMI In
E
HDMI Out
5
HDMI In
F
HDMI Out
6
HDMI In
G
HDMI Out
7
HDMI In
H
HDMI Out
8
HDMI In
12
34
V+
GND
GND
GND
V+
12
34
V+
GND
GND
GND
V+
2 3
3
4 71 6
5
1
CONTROL: This port is the link for Telnet control, connect to an active
Ethernet link with an RJ45 terminated cable (for further details, please
refer to section 6.7).
Warning: Please do not connect this port directly to the PC/Laptop
as the Telnet function will not work.
2
RS-232: Connect to a PC or control system with D-Sub 9-pin cable
for the transmission of RS-232 commands.
3
IR IN: Connect to the supplied IR extenders for IR signal reception
from the remote control of the Matrix. Ensure that the remote is
within the direct line-of-sight of the IR extender when used.
4
SERVICE: Manufacturer use only.
5
HDMI OUT A~H: Connect to HDMI equipped TVs or monitors for
display of the HDMI input source signal.
6
HDMI IN 1~8: Connect to the HDMI input source devices such as a
DVD player or a Set-top Box with HDMI cable or DVI to HDMI cable..
7
DC 24V: Plug the 24 V DC power supply into the unit and connect
the adaptor to an AC outlet.

5
6.3 Side Panel
1
1
FFan Ventilator: These are air ventilation areas, DO NOT block these
areas or cover it with any object. Please allow adequate space
around the unit for air circulation.
6.4 Remote Control
1
POWER: Press this button to
switch on the device or set it to
standby mode.
2
IN: Input ports selection 1~8.
3
OUT: Output ports selection A~H.
1
23

6
6.5 RS-232 Pin Assignment
CMSI-8H8HS Remote Control Console
PIN Assignment PIN Assignment
1 NC 1 NC
2Tx 2Rx
3Rx 3Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 19200 bps
Data Bit: 8-bit
Parity: None
Stop Bit: 1-bit
Flow Control: None

7
6.6 RS-232 and Telnet Commands
8
6.7 RS-232 and Telnet Commands
Command Description
A1~A8 Switch Output A to 1~8
B1~B8 Switch Output B to 1~8
C1~C8 Switch Output C to 1~8
D1~D8 Switch Output D to 1~8
E1~E8 Switch Output E to 1~8
F1~F8 Switch Output F to 1~8
G1~G8 Switch Output G to 1~8
H1~H8 Switch Output H to 1~8
ABCE…1~ABCD…8 Switch Output ABCD… to 1~8 at the
same time
SETIP <IP><SubNet><GW> Setting IP. SubNet.GateWay<Static IP>
RSTIP IP confi guration was reset to factory
defaults<DHCP>
IPCONFIG Display the current IP confi g
P0 Power Off
P1 Power On
I1~I8 Switch all the output to 1~8
ST Display the current matrix state and
fi rmware version
RS System Reset to H8
EM Setting EDID MODE. 1-STD 2-TV.
?Display all available commands
QUIT Exit (Telnet only)
Note: Any commands will not be executed unless followed by a
carriage return. Commands are not case-sensitive.

8
6.7 Telnet Control
9
6.8 Telnet Control
Before attempting to use the telnet control, please ensure that both
the Matrix (via the 'LAN /CONTROL' port) and the PC/Laptop are
connected to active networks.
Note: Please do not connect both the Matrix and the PC/Laptop with
a single CAT5e/6 cable as it will not access the telnet function.
To access the telnet control in Windows 7, click on the 'Start' menu
and type "cmd" in the Search fi eld then press enter.
Under Windows XP go to the 'Start' menu and click on "Run", type
"cmd" with then press enter.
Under Mac OS X, go to Go→Applications→Utilities→Terminal
See below for reference.

9
10
Once in the command line interface (CLI) type "telnet", a space, then
the IP address of the unit you wish to control, a space and "23", then
hit enter.
Note: The IP address of the Matrix can be displayed on the device's
LCM monitor by pressing the Menu button twice.
This will bring us into the device which we wish to control. Type "HELP"
to list the available commands.
Type “IPCONFIG” To show all IP confi gurations. To reset the IP,
type “RSTIP” and to use a set static IP, type ”SETIP” (For a full list of
commands, see Section 6.7).
Note: Any commands will not be executed unless followed by a
carriage return. Commands are not case-sensitive. If the IP is changed
then the IP Address required for Telnet access will also change
accordingly.

10
7. CONNECTION DIAGRAM
Router or
Wireless
Router
DC 24V
IR-In
RS-232 Service
A
HDMI Out
1
HDMI In
B
HDMI Out
2
HDMI In
C
HDMI Out
3
HDMI In
D
HDMI Out
4
HDMI In
E
HDMI Out
5
HDMI In
F
HDMI Out
6
HDMI In
G
HDMI Out
7
HDMI In
H
HDMI Out
8
HDMI In
12
34
V+
GND
GND
GND
V+
CONTROL
1
2
3
4
V+
GND
GND GND
V+
123456 87
Displays
HDMI Outputs
Source
Equipment
HDMI Inputs
8x8 HDMI
Matrix
RS-232 Equipped
PC or Notebook

11
8. SPECIFICATIONS
Video Bandwidth 255 MHZ/6.75 GBPS
Input Ports 8×HDMI, 1×RS-232, 1×IR Receiver,
1×Mini USB Type B (For firmware
update only), 1×RJ-45
Output Ports 8×HDMI
HDMI Input Cable Distance 15m/8-bit, 10m/12-bit
HDMI Output Cable Distance 15m/8-bit ,15m/12-bit
ESD Protection Human-body Model:
± 8kV (Air-gap discharge)
± 4kV (Contact discharge)
Power Supply 24 V/6.25 A DC (US/EU standards, CE/
FCC/UL certied)
Dimensions 438 mm (W)×255 mm (D)×93 mm (H)
Weight 4278 g
Chassis Material Metal
Silkscreen Color Black
Operating Temperature 0 ˚C~40 ˚C/32 ˚F~104 ˚F
Storage Temperature −20 ˚C~60 ˚C/−4 ˚F~140 ˚F
Relative Humidity 20~90 % RH (non-condensing)
Power Consumption 48 W

12
9. ACRONYMS
ACRONYM COMPLETE TERM
DTS Digital Theater System
DVI Digital Theater System
EDID Extended Display Identication Data
HDCP High-bandwidth Digital Content Protection
HDMI High-Denition Multimedia Interface
HDTV High Denition Television
LCM Liquid Crystal Module
USB Universal Serial Bus
VGA Video Graphics Array
WUXGA Widescreen Ultra Extended Graphics Array