d & b audiotechnik Z5150 User manual

Z5150
Q Swivel bracket
Mounting instructions

General Information
Mounting instructions
Z5150 Q Swivel bracket
Version 2.0E, 10/2003, 2952.E.02
© by d&b audiotechnik AG 2003; all rights reserved.
The information contained in this manual has been carefully
checked for accuracy, at the time of going to press, however no
guarantee is given with respect to the correctness.
d&b audiotechnik AG accepts no responsibility for any errors or
inaccuracies that may appear in this manual or the products and
software described in it.
Technical specifications, dimensions, weights and properties do not
represent guaranteed qualities.
As manufacterers we reserve the right to make alterations and
modifications within the framework of legal provisions, as well as
changes aimed at improving quality.
d&b audiotechnik AG
Eugen-Adolff-Strasse 134, -71522 Backnang, Germany
Telephone [phone], Fax [phone]
E-mail: [email protected], Internet: www.dbaudio.com
References in the manual
W RNING!
This refers to a potentially dangerous situation
which may lead to personal injury.
C UTION!
This refers to a potentially dangerous situation
which may lead to damage to the equipment.
IMPORT NT!
This refers to a situation which may cause the
equipment to malfunction.
Symbols on the equipment
Please refer to the information in the operating
manual.

Z5150
(2.0E) Page 3 of 4
Z5150 Q Swivel bracket
The L shaped Z5150 Q Swivel bracket allows a d&b Q7
loudspeaker cabinet to be mounted and set to a variety of
horizontal or vertical angles.
Using the Z5024 Loudspeaker stand adapter together with the Q
Swivel bracket enables a Q7 loudspeaker to be mounted onto a
loudspeaker stand (e.g. Z5013, Z5009 or E6001) with a tube
diameter of 35 mm/1.4”.
The Z5150 Q Swivel bracket allows single Q7 cabinets to be flown
vertically using the Z5010 TV spigot with fixing plate or the Z5029
TV spigot. Both can be used in conjunction with the Z5012 Pipe
clamp for hanging cabinets from overhead bars or truss with a
tube diameter between 32 mm to 50 mm (1.25” to 1.97”).
Safety instructions
[S]
[F]
DO NOT
UNLOCK PIN TO
ADJUST ANGLE
CAUTION ONLY UNLOCK FOR
DISASSEMBLY ON
GROUND
W RNING!
Installation should only be carried out by fully
trained personel. There are certain rules for
installation that must be complied with.
It is essential to secure the cabinet with the securing
pin [S] before lifting the cabinet or placing it onto a
loudspeaker stand.
The bracket and loudspeaker must have all locking
devices (fixing screw [F] and the securing pin [S])
secured when in use.
Under no circumstances should the securing pin [S]
be unlocked to adjust the vertical angle of the
cabinet.
Secondary safeties must always be provided and used
when flying or fixing loudspeaker loads overhead.
Load safety information
W RNING!
The Z5150 Q Swivel bracket is designed to support
one d&b Q7 loudspeaker cabinet.
No additional loads must be added.
The bracket may only be used in an upright position
or suspended vertically.
Part list Z5150 Q Swivel bracket
[S]
[1]
−
1 x Z5150 Q Swivel bracket [1] with securing pin [S] that is
attached to the bracket by a steel wire.
Weight Z5150 Q Swivel bracket
2.5 kg/5.5 lb

Z5150
(2.0E) Page 4 of 4
d&b audiotechnik G, Eugen- dolff-Str. 134, D-71522 Backnang, Germany, Phone [phone], Fax [phone]
ssembly
↓→
↓
1. 2 .
3. 4.
G
S
The Z5150 Q Swivel bracket is connected to the quick lock adapter
plate of the cabinet as shown in the graphic opposite:
1. Attach the bracket fixing plate into the recessed holes of the
cabinets quick lock adapter plate.
2. Slide the fixing plate towards the front of the cabinet until it is
fixed in place.
3. Insert the securing pin
[S] into the respective recess.
4. Ensure that the securing pin
[S] is locked. A groove [G] in the
bolt of the securing pin indicates that it is properly locked.
Operation
[F]
The centre of gravity of a Q7 loudspeaker is in line with the
bracket’s axis of rotation. This allows the vertical angle of the
loudspeaker to be set as required without exerting any twisting
forces on the mounting supports, an essential requirement for
stable flying. The vertical angle of the loudspeaker is locked using
the fixing screw
[F] .
After slackening the fixing screw set the loudspeaker to the
required vertical angle and retighten the fixing screw.
Z5150 dimensions in mm [inch]
Z5150 Q Swivel bracket with
Z5029 TV spigot
Q7 with
Z5150 Q Swivel bracket,
Z5024 Loudspeaker stand adapter,
Z5013 Loudspeaker stand winder M20
and Q-SUB
280
[11"]
41,24
[1.62"]
30
[1.18"]
79,24
[3.12"]
61,27
[2.41"]
55,60
[2.19"]
288
[11.34"]
115
[4.53"]
M10
M8
12,50
[0.5"]
165,50
[6.51"]
460,75
[18.14"]
50
[1.97"]
M8