D-Link DGS-1510/ME Series User manual

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
I
Table of Contents
Chapter 1 Using Command Line Interface.................................................................................................................1
Chapter 2 Basic Command List .................................................................................................................................8
Chapter 3 802.1Q VLAN Command List..................................................................................................................22
Chapter 4 802.1X Command List.............................................................................................................................36
Chapter 5 Access Authentication Control Command List........................................................................................51
Chapter 6 Access Control List (ACL) Command List...............................................................................................72
Chapter 7 Address Resolution Protocol (ARP) Command List................................................................................91
Chapter 8 ARP Spoofing Prevention Command List...............................................................................................96
Chapter 9 Auto-Configuration Command List..........................................................................................................98
Chapter 10 Basic Commands Command List..........................................................................................................101
Chapter 11 BPDU Attack Protection Command List................................................................................................118
Chapter 12 Cable Diagnostics Command List.........................................................................................................123
Chapter 13 Command Logging Command List........................................................................................................125
Chapter 14 Compound Authentication Command List ............................................................................................127
Chapter 15 Configuration Command List.................................................................................................................131
Chapter 16 Connectivity Fault Management (CFM) Command List........................................................................136
Chapter 17 CPU Interface Filtering Command List..................................................................................................163
Chapter 18 Debug Software Command List............................................................................................................172
Chapter 19 DHCP Local Relay Command List........................................................................................................179
Chapter 20 DHCP Relay Command List..................................................................................................................185
Chapter 21 DHCP Server Screening Command List...............................................................................................201
Chapter 22 Digital Diagnostic Monitoring (DDM) Commands .................................................................................204
Chapter 23 D-Link Unidirectional Link Detection (DULD) Command List................................................................210
Chapter 24 DoS Attack Prevention Command List..................................................................................................212
Chapter 25 Energy Efficient Ethernet (EEE) Command List ...................................................................................216
Chapter 26 Ethernet Ring Protection Switching (ERPS) Command List.................................................................218
Chapter 27 Filter Command List..............................................................................................................................227
Chapter 28 Filter Database (FDB) Command List...................................................................................................230
Chapter 29 Flash File System (FFS) Command List...............................................................................................240
Chapter 30 Gratuitous ARP Command List.............................................................................................................249
Chapter 31 IGMP Snooping Command List.............................................................................................................254
Chapter 32IP-MAC-Port Binding (IMPB) Command List........................................................................................280
Chapter 33 IPv6 Neighbor Discover Command List................................................................................................295
Chapter 34 IPv6 Route Command List....................................................................................................................299
Chapter 35 Jumbo Frame Command List................................................................................................................302
Chapter 36 Layer 2 Protocol Tunneling (L2PT) Command List...............................................................................304
Chapter 37 Link Aggregation Command List...........................................................................................................308
Chapter 38 Link Layer Discovery Protocol (LLDP) Command List..........................................................................315
Chapter 39 LLDP-MED Command List....................................................................................................................333

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
II
Chapter 40 Loop Back Detection (LBD) Command List..........................................................................................341
Chapter 41MAC Notification Command List...........................................................................................................347
Chapter 42 MAC-based Access Control Command List..........................................................................................352
Chapter 43 MAC-based VLAN Command List.........................................................................................................367
Chapter 44 Mirror Command List.............................................................................................................................370
Chapter 45 MLD Snooping Command List..............................................................................................................373
Chapter 46 MSTP debug enhancement Command List..........................................................................................395
Chapter 47 Multicast Filter Command List...............................................................................................................401
Chapter 48 Multicast VLAN Command List .............................................................................................................412
Chapter 49 Multiple Spanning Tree Protocol (MSTP) Command List.....................................................................422
Chapter 50 Network Load Balancing (NLB) Command List ....................................................................................434
Chapter 51 Network Monitoring Command List.......................................................................................................439
Chapter 52 OAM Commands...................................................................................................................................445
Chapter 53 Peripherals Command List....................................................................................................................452
Chapter 54 Ping Command List...............................................................................................................................455
Chapter 55 Port Security Command List .................................................................................................................457
Chapter 56 Power over Ethernet (PoE) Command List (DGS-1510-28LP/ME and DGS-1510-28XMP/ME Only).465
Chapter 57 PPPoE Circuit ID Insertions Command List..........................................................................................470
Chapter 58 Protocol VLAN Command List ..............................................................................................................473
Chapter 59 QinQ Command List..............................................................................................................................479
Chapter 60 Quality of Service (QoS) Command List...............................................................................................487
Chapter 61 RADIUS Client Command List..............................................................................................................505
Chapter 62 Safeguard Engine Command List.........................................................................................................515
Chapter 63 Secure Shell (SSH) Command List.......................................................................................................517
Chapter 64Secure Sockets Layer (SSL) Command List ........................................................................................525
Chapter 65 Show Technical Support Command List...............................................................................................531
Chapter 66 Simple Mail Transfer Protocol (SMTP) Command List.........................................................................534
Chapter 67 Simple Network Management Protocol (SNMP) Command List ..........................................................539
Chapter 68 Single IP Management Command List..................................................................................................564
Chapter 69 Syslog and Trap Source-interface Command List................................................................................574
Chapter 70 System Log Command List...................................................................................................................578
Chapter 71 System Severity Command List............................................................................................................589
Chapter 72 Telnet Client Command List..................................................................................................................591
Chapter 73 TFTP/FTP Client Command List...........................................................................................................592
Chapter 74 Time and SNTP Command List ............................................................................................................601
Chapter 75 Trace Route Command List..................................................................................................................608
Chapter 76 Traffic Control Command List ...............................................................................................................611
Chapter 77 Traffic Segmentation Command List.....................................................................................................616
Chapter 78 Trusted Host Command List .................................................................................................................618
Chapter 79 Unicast Routing Command List.............................................................................................................622
Chapter 80 VLAN Trunking Command List..............................................................................................................625
Chapter 81 Password Recovery Command List......................................................................................................630

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
III
Appendix A Password Recovery Procedure.............................................................................................................632
Appendix B System Log Entries...............................................................................................................................633
Appendix C Trap Log Entries....................................................................................................................................643
Appendix D RADIUS Attributes Assignment.............................................................................................................647
Appendix E IETF RADIUS Attributes Support..........................................................................................................649

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
1
Chapter 1 Using Command Line Interface
The Switch can be managed through the Switch’s serial port, Telnet, SNMP or the Web-based management agent.
The Command Line Interface (CLI) can be used to configure and manage the Switch via the serial port or Telnet
interfaces.
This manual provides a reference for all of the commands contained in the CLI. Every command will be introduced
in terms of purpose, format, description, parameters, and examples. Configuration and management of the Switch
via the Web-based management agent are discussed in the Web UI Reference Guide. For detailed information on
installing hardware please also refer to the Hardware Installation Guide.
1-1 Accessing the Switch via the Serial Port
The Switch’s serial port’s default settings are as follows:
• 115200 baud
• no parity
• 8 data bits
• 1 stop bit
A computer running a terminal emulation program capable of emulating a VT-100 terminal and a serial port
configured as above are then connected to the Switch’s Console port via an included RS-232 to RJ-45 convertor
cable.
With the serial port properly connected to a management computer, the following screen should be visible. If this
screen does not appear, try pressing Ctrl+r to refresh the console screen.
DGS-1510-28XMP/ME Gigabit Ethernet Switch
Command Line Interface
Firmware: Build 1.00.018
Copyright(C) 2015 D-Link Corporation. All rights reserved.
UserName:
PassWord:
DGS-1510-28XMP/ME:admin#
There is no initial username or password. Just press the Enter key twice to display the CLI input cursor −DGS-
1510-28XMP/ME:admin#. This is the command line where all commands are input.
1-2 Setting the Switch’s IP Address
Each Switch must be assigned its own IP Address, which is used for communication with an SNMP network
manager or other TCP/IP application (for example BOOTP, TFTP). The Switch’s default IP address is 10.90.90.90.
You can change the default Switch IP address to meet the specification of your networking address scheme.
The Switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can
be found on the initial boot console screen – shown below.

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
2
Boot Procedure V1.00.001
-------------------------------------------------------------------------------
Power On Self Test ........................................ 100 %
MAC Address : 00-01-02-03-04-00
H/W Version : A1
Please Wait, Loading V1.00.018 Runtime Image .............. 100 %
UART init ................................................. 100 %
Starting runtime image
Device Discovery .......................................... 100 %
Configuration init ........................................ |
The Switch’s MAC address can also be found in the Web management program on the Switch Information (Basic
Settings) window on the Configuration menu.
The IP address for the Switch must be set before it can be managed with the Web-based manager. The Switch IP
address can be automatically set using BOOTP or DHCP protocols, in which case the actual address assigned to
the Switch must be known.
Starting at the command line prompt, enter the commands config ipif System ipaddress
xxx.xxx.xxx.xxx/yyy.yyy.yyy.yyy. Where the x’s represent the IP address to be assigned to the IP interface
named System and the y’s represent the corresponding subnet mask.
Alternatively, you can enter config ipif System ipaddress xxx.xxx.xxx.xxx/z. Where the x’s represent the IP
address to be assigned to the IP interface named System and the zrepresents the corresponding number of
subnets in CIDR notation.
The IP interface named System on the Switch can be assigned an IP address and subnet mask which can then be
used to connect a management station to the Switch’s Telnet or Web-based management agent.
DGS-1510-28XMP/ME:admin# config ipif System ipaddress 10.24.22.100/255.0.0.0
Command: config ipif System ipaddress 10.24.22.100/8
Success.
DGS-1510-28XMP/ME:admin#
In the above example, the Switch was assigned an IP address of 10.24.22.100 with a subnet mask of 255.0.0.0.
The system message Success indicates that the command was executed successfully. The Switch can now be
configured and managed via Telnet, SNMP MIB browser and the CLI or via the Web-based management agent
using the above IP address to connect to the Switch.
There are a number of helpful features included in the CLI. Entering the ?command will display a list of all of the
top-level commands.

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
3
..
?
cable_diag ports
cd
cfm linktrace
cfm loopback
clear
clear address_binding dhcp_snoop binding_entry ports
clear arptable
clear attack_log
clear cfm pkt_cnt
clear counters
clear ethernet_oam ports
clear fdb
clear igmp_snooping data_driven_group
clear igmp_snooping statistics counter
clear log
clear mac_based_access_control auth_state
clear mld_snooping data_driven_group
clear mld_snooping statistics counter
clear port_security_entry
config 802.1p default_priority
CTRL+C ESC qQuit SPACE nNext Page ENTER Next Entry aAll
When entering a command without its required parameters, the CLI will prompt you with a Next possible
completions: message.
DGS-1510-28XMP/ME:admin# config account
Command: config account
Next possible completions:
<username>
DGS-1510-28XMP/ME:admin#
In this case, the command config account was entered with the parameter <username>. The CLI will then
prompt to enter the <username> with the message, Next possible completions:. Every command in the CLI has
this feature, and complex commands have several layers of parameter prompting.
In addition, after typing any given command plus one space, users can see all of the next possible sub-commands,
in sequential order, by repeatedly pressing the Tab key.
To re-enter the previous command at the command prompt, press the up arrow cursor key. The previous
command will appear at the command prompt.
DGS-1510-28XMP/ME:admin#config account
Command: config account
Next possible completions:
<username>
DGS-1510-28XMP/ME:admin#config account
In the above example, the command config account was entered without the required parameter <username>,
the CLI returned the Next possible completions: <username> prompt. The up arrow cursor control key was

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
4
pressed to re-enter the previous command (config account) at the command prompt. Now the appropriate
username can be entered and the config account command re-executed.
All commands in the CLI function in this way. In addition, the syntax of the help prompts are the same as presented
in this manual −angle brackets < > indicate a numerical value or character string, braces { } indicate optional
parameters or a choice of parameters, and brackets [ ] indicate required parameters.
If a command is entered that is unrecognized by the CLI, the top-level commands will be displayed under the
Available commands: prompt.
DGS-1510-28XMP/ME:admin#the
Available commands:
.. ? cable_diag cd
cfm clear config copy
create debug del delete
dir disable download enable
erase login logout md
move no ping ping6
rd reboot reconfig rename
reset save show smtp
telnet traceroute traceroute6 upload
DGS-1510-28XMP/ME:admin#
The top-level commands consist of commands such as show or config. Most of these commands require one or
more parameters to narrow the top-level command. This is equivalent to show what? or config what? Where the
what? is the next parameter.
For example, entering the show command with no additional parameters, the CLI will then display all of the
possible next parameters.

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
5
Command: show
Next possible completions:
802.1p 802.1x access_profile account
accounting acct_client address_binding
arp_spoofing_prevention arpentry attack_log
auth_client auth_diagnostics auth_session_statistics
auth_statistics authen authen_enable authen_login
authen_policy authentication authorization autoconfig
bandwidth_control boot_file bpdu_protection cfm
command command_history config cpu
cpu_filter current_config ddm device_status
dhcp_local_relay dhcp_relay dos_prevention
dot1v_protocol_group dscp duld
eee environment erps error
ethernet_oam fdb filter flow_meter
gratuitous_arp greeting_message gvrp hol_prevention
igmp igmp_snooping ipif
ipif_ipv6_link_local_auto iproute ipv6
ipv6route jumbo_frame l2protocol_tunnel lacp_port
limited_multicast_addr link_aggregation lldp
log log_save_timing log_software_module
loopdetect mac_based_access_control
mac_based_access_control_local mac_based_vlan mac_notification
max_mcast_group mcast_filter_profile mirror
mld_snooping multicast multicast_fdb nlb
packet password_recovery per_queue poe
port port_security port_security_entry
port_vlan ports pppoe pvid
qinq radius rmon router_ports
safeguard_engine scheduling scheduling_mechanism
serial_port session sim smtp
snmp sntp ssh ssl
storage_media_info stp switch
syslog system_severity tech_support terminal
tftp time time_range traffic
traffic_segmentation trap trusted_host
utilization vlan vlan_translation vlan_trunk
DGS-1510-28XMP/ME:admin#
In the above example, all of the possible next parameters for the show command are displayed. At the next
command prompt, the up arrow was used to re-enter the show command, followed by the account parameter.
The CLI then displays the user accounts configured on the Switch.
1-3 Command Syntax Symbols
Each CLI command, available on this switch, contains certain syntax symbols that might be unfamiliar to the
inexperienced user. Each syntax symbol carries a meaning and by knowing that meaning we can better
understand how the command is used. All commands are case-sensitive. Be sure to disable the Caps Lock or any
other unwanted function that changes text case.

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
6
Syntax Description
angle brackets < > This syntax is used to enclose a variable or a value. Users must enter the variable or
value. For example, in the config command_prompt [<string 16> | username |
default] command, users must enter the command prompt string value and NOT the
parameter <string 16>.
square brackets [ ] This syntax is used to enclose a required value or list of required arguments. Only one
value or argument must be specified. For example, in the config command_prompt
[<string 16> | username | default] command, users must enter either the command
prompt string, select the username, or select the default option. Do not type the square
brackets.
vertical bar | This syntax is used to separate mutually exclusive items in a list. For example, in the
reset {[config | system]} {force_agree} command, users may choose config or
system in the command. Do not type the vertical bar.
braces { } This syntax is used to enclose an optional value or a list of optional arguments. One or
more values or arguments can be specified. For example, in the reset {[config |
system]} {force_agree} command, users may choose config or system in the
command. Do not type the braces.
parentheses ( ) This syntax is used to indicate that at least one or more of the values or arguments in
the preceding syntax enclosed by braces must be specified. For example, in the
config dhcp_relay {hops <int 1-16> | time <sec 0-65535>}(1) command, users have
the option to specify hops or time or both of them. The "(1)" following the set of braces
indicates at least one argument or value within the braces must be specified. Do not
type the parentheses.
ipif <ipif_name 12> In this syntax example, the value 12 means that the IP interface name can be up to 12
characters long.
metric <value 1-31> In this syntax example, the values 1-31 means that the metric value must be between
1 and 32.
1-4 Line Editing Keys
Keys Description
Delete This key specifies to delete the character under the cursor and to shift the remainder
of the line to the left.
Backspace This key specifies to delete the character to the left of cursor and shift the remainder of
the line to the left.
CTRL+R This key specifies to replace text characters with newly typed text or to insert newly
typed text within the existing sentence. This is similar to the Insert key.
Up Arrow This key specifies to repeat the previously entered command. Each time the up arrow
is pressed, the command previous to that displayed appears. This way it is possible to
review the command history for the current session. Use the down arrow to progress
sequentially forward through the command history list.
Down Arrow This key specifies to display the next command in the command history entered in the
current session. This displays each command sequentially as it was entered. Use the
up arrow to review previous commands.
Left Arrow This key specifies to move the cursor to the left.
Right Arrow This key specifies to move the cursor to the right.
Tab This key specifies to help users to select the appropriate token.

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
7
1-5 Multiple Page Display Control Keys
When CLI paging is enabled, the screen display will pause when the show command output reaches the end of the
page, as shown below.
DGS-1510-28XMP/ME:admin#show stp ports
Command: show stp ports
MSTP Port Information
----------------------
Port Index : 1 , Hello Time: 2 /2 , Port STP : Enabled ,
External PathCost : Auto/200000 , Edge Port : True /No , P2P : Auto /Yes
Port RestrictedRole : False, Port RestrictedTCN : False
Port Forward BPDU : Disabled
MSTI Designated Bridge Internal PathCost Prio Status Role
----- ------------------ ----------------- ---- ---------- ----------
0 N/A 200000 128 Forwarding NonStp
CTRL+C ESC qQuit SPACE nNext Page pPrevious Page rRefresh
The following control keys will then be available:
Keys Description
CTRL+C Stops the display of remaining pages when multiple pages are to be displayed.
ESC Stops the display of remaining pages when multiple pages are to be displayed.
q Stops the display of remaining pages when multiple pages are to be displayed.
SPACE Displays the next page.
n Displays the next page.
p Displays the previous page.
r Refreshes the pages currently displayed.
a Displays the remaining pages without pausing between pages.
Enter Displays the next line or table entry.

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
8
Chapter 2 Basic Command List
show session
show serial_port
config serial_port {baud_rate [9600 | 19200 | 38400 | 115200] | auto_logout [never | 2_minutes | 5_minutes |
10_minutes | 15_minutes]}
enable clipaging
disable clipaging
login
logout
?
clear
show command_history
config command_history <value 1-40>
config greeting_message {default}
show greeting_message
config command_prompt [<string 16> | username | default]
config terminal width [default | <value 80-200>]
show terminal width
config ports [<portlist> | all] {medium_type [fiber | copper]} {speed [auto | 10_half | 10_full | 100_half | 100_full |
1000_full {[master | slave]} | 10g_full] | flow_control [enable | disable] | learning [enable | disable] | state
[enable | disable] | mdix [auto | normal | cross] | [description <desc 1-32> | clear_description]}
show ports {<portlist>} {[description | err_disabled | details | media_type]}
2-1 show session
Description
This command is used to display a list of currently users which are login to the Switch.
Format
show session
Parameters
None.
Restrictions
Only Administrators and Operators can issue this command.
Example
To display the session entries:

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
9
ID Live Time From Level Name
--- ------------ --------------------------------------- ----- ---------------
0 00:01:46.360 10.90.90.10 puser puser
8 00:05:49.340 Serial Port admin admin
Total Entries: 2
CTRL+C ESC qQuit SPACE nNext Page pPrevious Page rRefresh
2-2 show serial_port
Description
This command is used to display the current serial port settings.
Format
show serial_port
Parameters
None.
Restrictions
None.
Example
To display the serial port setting:
DGS-1510-28XMP/ME:admin# show serial_port
Command: show serial_port
Baud Rate : 115200
Data Bits : 8
Parity Bits : None
Stop Bits : 1
Auto-Logout : 10 mins
DGS-1510-28XMP/ME:admin#
2-3 config serial_port
Description
This command is used to configure the serial bit rate that will be used to communicate with the management host
and the auto logout time for idle connections.

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
10
Format
config serial_port {baud_rate [9600 | 19200 | 38400 | 115200] | auto_logout [never | 2_minutes | 5_minutes |
10_minutes | 15_minutes]}
Parameters
baud_rate - (Optional) Specifies the serial bit rate that will be used to communicate with the management host.
The default baud rate is 115200.
9600 - Specifies the serial bit rate to be 9600.
19200 - Specifies the serial bit rate to be 19200.
38400 - Specifies the serial bit rate to be 38400.
115200 - Specifies the serial bit rate to be 115200.
auto_logout - (Optional) Specifies the auto logout time out setting.
never - Never timeout.
2_minutes - Specifies that the device will auto logout when idle over 2 minutes.
5_minutes - Specifies that the device will auto logout 2hen idle over 5 minutes.
10_minutes - Specifies that the device will auto logout when idle over 10 minutes.
15_minutes - Specifies that the device will auto logout when idle over 15 minutes.
Restrictions
Only Administrators and Operators can issue this command.
Example
To configure baud rate:
DGS-1510-28XMP/ME:admin# config serial_port baud_rate 9600
Command: config serial_port baud_rate 9600
Success.
DGS-1510-28XMP/ME:admin#
2-4 enable clipaging
Description
This command is used to enable the pausing of the screen display when the show command output reaches the
end of the page. The default setting is enabled.
Format
enable clipaging
Parameters
None.
Restrictions
Only Administrators and Operators can issue this command.

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
11
Example
To enable pausing of the screen display when show command output reaches the end of the page:
DGS-1510-28XMP/ME:admin# enable clipaging
Command: enable clipaging
Success.
DGS-1510-28XMP/ME:admin#
2-5 disable clipaging
Description
This command is used to disable the pausing of the screen display when the show command output reaches the
end of the page. The default setting is enabled.
Format
disable clipaging
Parameters
None.
Restrictions
Only Administrators and Operators can issue this command.
Example
To disable pausing of the screen display when show command output reaches the end of the page:
DGS-1510-28XMP/ME:admin# disable clipaging
Command: disable clipaging
Success.
DGS-1510-28XMP/ME:admin#
2-6 login
Description
This command is used to allow user login to the Switch.
Format
login

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
12
Parameters
None.
Restrictions
None.
Example
To login the Switch with a user name dlink:
DGS-1510-28XMP/ME:admin# login
Command: login
UserName:dlink
PassWord:****
DGS-1510-28XMP/ME:admin#
2-7 logout
Description
This command is used to logout the facility.
Format
logout
Parameters
None.
Restrictions
None.
Example
To logout current user:

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
13
DGS-1510-28XMP/ME:admin# logout
Command: logout
**********
* Logout *
**********
DGS-1510-28XMP/ME Gigabit Ethernet Switch
Command Line Interface
Firmware: Build 1.00.018
Copyright(C) 2015 D-Link Corporation. All rights reserved.
UserName:
2-8 ?
Description
This command is used to display the usage description for all commands or the specific one.
Format
?
Parameters
None.
Restrictions
None.
Example
To get “ping” command usage, descriptions:
DGS-1510-28XMP/ME:admin#? ping
Command: ? ping
Command: ping
Usage: <ipaddr> { times <value 1-255> | timeout <sec 1-99>}
Description: Used to test the connectivity between network devices.
DGS-1510-28XMP/ME:admin#
2-9 clear
Description
The command is used to clear screen.

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
14
Format
clear
Parameters
None.
Restrictions
None.
Example
To clear screen:
DGS-1510-28XMP/ME:admin# clear
Command: clear
DGS-1510-28XMP/ME:admin#
2-10 show command_history
Description
The command is used to display command history.
Format
show command_history
Parameters
None.
Restrictions
None.
Example
To display command history:

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
15
DGS-1510-28XMP/ME:admin# show command_history
Command: show command_history
? ping
login
show serial_port
show session
? config bpdu_protection ports
? reset
? create account
? create ipif
show
the
?
DGS-1510-28XMP/ME:admin#
2-11 config command_history
Description
This command is used to configure the number of commands that the Switch can recall. The Switch “remembers”
up to the last 40 commands you entered.
Format
config command_history <value 1-40>
Parameters
<value 1-40> - Enter the number of commands that the Switch can recall. This value must be between 1 and 40.
Restrictions
Only Administrators and Operators can issue this command.
Example
To configure the number of command history:
DGS-1510-28XMP/ME:admin# config command_history 25
Command: config command_history 25
Success.
DGS-1510-28XMP/ME:admin#
2-12 config greeting_message
Description
This command is used to configure the greeting message (or banner).

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
16
Format
config greeting_message {default}
Parameters
default - (Optional) Specifies to return the greeting message (banner) to its original factory default entry.
Restrictions
Only Administrators and Operators can issue this command.
Example
To edit the banner:
DGS-1510-28XMP/ME:admin#config greeting_message
Command: config greeting_message
Greeting Messages Editor
================================================================================
DGS-1510-28XMP/ME Gigabit Ethernet Switch
Command Line Interface
Firmware: Build 1.00.018
Copyright(C) 2015 D-Link Corporation. All rights reserved.
================================================================================
<Function Key> <Control Key>
Ctrl+C Quit without save left/right/
Ctrl+W Save and quit up/down Move cursor
Ctrl+D Delete line
Ctrl+X Erase all setting
Ctrl+L Reload original setting
-------------------------------------------------------------------------------
2-13 show greeting_message
Description
The command is used to display greeting message.
Format
show greeting_message
Parameters
None.