D-Link DIR-868L User manual

ETISALAT Plug & Play Firmware
Wireless AC1750Dual Band
Gigabit Router
D-link DIR-868L
User Manual

Version 1.0 Page 1of 14
System Requirements
Network Requirements
• An Ethernet-based cable or DSL modem
• IEEE 802.11ac/n/g/b/a wireless clients
• 10/100/1000 Mbps Ethernet
Web-based Configuration
Utility Requirements
Computer with the following:
• Windows®, Macintosh, or Linux-based operating system
• An installed Ethernet adapter
Browser Requirements:
• Internet Explorer 7 or higher
• Firefox 12 or higher
• Safari 4 or higher
• Chrome 20 or higher
Windows® Users: Make sure you have the latest version of Java
Installed. Visit www.java.com to download the latest version.
mydlink Requirements
• IPhone/iPad/iPod touch (iOS 4.3 or higher)
• Android device (2.3.3 or higher)
• Computer with the following browser requirements:
• Internet Explorer 7 or higher
• Firefox 12 or higher
• Safari 5 or higher
• Chrome 20 or higher
iPhone, iPad, and iPod touch are registered trademarks of Apple Inc. Android is a trademark of Google, Inc.

Version 1.0 Page 2of 14
Hardware Overview
LEDs

Version 1.0 Page 3of 14
Hardware Overview
Connections

Version 1.0 Page 4of 14
Admin Login Page
If this is your first time installing the router, open your web browser and,
enter The IP address of the router (default: http://192.168.1.1)
a. Give the default Username and Password to login to the router (Username and Password
will be mentioned on the sticker at the back of your router)
Note: If no admin password mentioned, use “admin” as username and password.
b. To Change “admin” password
Go to Administration » Users and edit admin.

Version 1.0 Page 5of 14
1) WAN Setting ( Setup INTERNET Connection )
To configure wan settings,
Go to Network » WAN » WAN IPv4 Configuration
a) Connection Mode –Auto via ACS ( For ETISALAT Plug & Play Connection )
*All configuration including username, password and Vlan Id information will be pushed by Etisalat
ACS.

Version 1.0 Page 6of 14
b) ISP Connection type - PPPoE (Manual)
Give the Username and Password provided by your ISP in the User Name and Password
column and save the settings, enable Vlan only if it is required by ISP.

Version 1.0 Page 7of 14
2) LAN Setting & DHCP
To change lan setting and DHCP ,
Go to Network » LAN » LAN IPv4 Configuration
. By default the IP address is 192.168.1.1 & DHCP Pool is 100 ~254

Version 1.0 Page 8of 14
3) Wireless Configuration
Go to Wireless » Profiles
Then Right click and Edit 2.4GHz or 5GHz to change the SSID and Security.
a. 2.4 GHz
b. 11AC 5 GHz

Version 1.0 Page 9of 14
4) Port Forwarding
a. To create port forwarding rules ,
Go to Security » Firewall » Port Forwarding and then “Add New Port Forwarding Rule”,
You can choose the predefined services or the added custom services.
b. Custom services
Go to Security» Firewall » Custom Services and “Add New Custom Service”,
*Custom service is required if the service is not listed on the available services.

Version 1.0 Page 10 of 14

Version 1.0 Page 11 of 14
5) Firewall Rules
To add firewall rule to allow or deny network access, go to Security » Firewall » Firewall Rules IPv4
and “Add New IPv4 Firewall Rule”,

Version 1.0 Page 12 of 14
6) Parental Control
First Enable Content Filtering
Go to Security » Content Filtering
Then Go to Security » Content Filtering » Blocked Keywords and “ Add New Blocked Keyword” ,

Version 1.0 Page 13 of 14
We can also Schedule the URL blocking,
Go to Security » Firewall » Schedules and “Add New Schedule “,
Then Go to Security » Content Filtering and Select the schedule you have created ,

Version 1.0 Page 14 of 14
7) Dynamic DNS
To enable Dynamic DNS Go to Network » Advanced » DDNS
8) To Reset & Reboot the router
Go to Administration »Firmware » Backup/Restore
----------------------END------------------