D-Link DSL-G604T User manual

Quick Installation Guide for DSL-G604T Page 1 of 4 July 2004
Quick Installation Guide for DSL-G604T (July 2004)
(for Users in Thailand ONLY)
1. DSL-G604T is a 3-in1 802.11g 54Mbps wireless ADSL router, which has a built-in
ADSL modem. DSL-G604T has integrated 802.11g wireless access point and a four-port
(10/100Mbps) switch. Without additional equipment, DSL-G604T allows all of the
wired & wireless computers in your home or office network to access the broadband
Internet at the same time via a single ADSL telephone line.
Follow the steps below to configure DSL-G604T.
2. Configure your PC to “Obtain an IP Address Automatically” from DSL-G604T,
which is pre-configured as DHCP server. Connect you PC to DSL-G604T Ethernet port
as shown in Figure 1.
Click Network connection icon at the bottom right hand corner of Windows & follow
the steps from [i] to [vi].
Once it is completed, the computer is configured as DHCP client, which will obtain an
IP address from DSL-G604T automatically.
DSL
-
G604T
UTP Straight Cable
Figure 1
Step i
Step ii
Step iii
Step iv
Step v
Step vi
ADSL Telephone Line

Quick Installation Guide for DSL-G604T Page 2 of 4 July 2004
3. Run the IE and make sure under [Tools] -> [Internet Options] -> [Connections] ->
[LAN Settings], “Proxy Server” is un-checked.
4. Step 1: Enter the default IP address 192.168.1.1 in the URL address field.
Step 2: Enter default Login Name “admin”, Password “admin” and click [Login].
Setup PPPoE Connection
5. Goto Section [7] for the configuration of PPPoA connection.
Step 3a/4a: Click [Setup] and choose [Connection 1].
Step 1
Step 2
Step 3a
Step 4a
Step 5a
Step 6a
Step 8a
Step 7a
Step 9a

Quick Installation Guide for DSL-G604T Page 3 of 4 July 2004
6. Step 5a: Rename the connection name.
Step 6a: Select PPPoE.
Step 7a: Enter Username & Password of ADSL broadband account.
Step 8a: Enter the VPI & VCI values.
Note:
i. Both VPI and VCI values are provided by ISP. Please obtain these values from your
ISP. For TA ADSL line, you may use VPI: 0 / VCI: 100 and Type: PPPoE.
ii. Different ISP may have different VPI and VCI values.
Step 9a: Click Apply to save the changes & goto Section [9].
Setup PPPoA Connection
7. Step 3b/4b: Click [Setup] and choose [Connection 1]
8. Step 5b: Rename the connection name
Step 6b: Select PPPoA
Step 7b: Select LLC or VC (Please check with your ISP.)
Step 8b: Enter Username and Password
Step 9b: Enter the VPI and VCI values
Note:
i. Both VPI and VCI values are provided by ISP. Please obtain these values from your
ISP. For TA ADSL line, you may use VPI: 0 / VCI: 100 and Type: PPPoE.
ii. Different ISP may have different VPI and VCI values.
Step 10b: Click Apply to save the changes.
Step 3b
Step 4b
Step 5b
Step 6b
Step 7b
Step 8b
Step 9b
Step 10b

Quick Installation Guide for DSL-G604T Page 4 of 4 July 2004
9. Step 11: Click Tools.
Step 12: Click System Commands.
Step 13: Click Save All.
For any assistance, kindly access www.dlink.in.th or email us [e-mail].
D-Link International Pte Ltd
Office: (65) 6774-6233
Fax: [phone]
Step 11
Step 12
Step 13