D-Link Ethernet Broadband Router DIR-100 User manual

Quick Install Guide
DIR-100
Version 1.00

2
System Requirements
• Ethernet-based Cable or DSL Modem
• Computers with Windows®, Macintosh®, or Linux-based operating
systems with an installed Ethernet adapter
• Internet Explorer 6.x and above, or Netscape®Navigator 7.0 and
above
Package Contents
System Requirements
If any of the above items are missing, please contact your reseller.
CAT5 Ethernet Cable Power Adapter
D-Link DIR-100 CD-ROM with
Manual

3
Hardware Overview
Hardware Overview
Status LED
A blinking light indicates that
the DIR-100 is functioning
properly.
Local Network LEDs
Asolid light on each port indicates
a connection to an Ethernet
enabled device. These LEDs
blink during data transmission.
WAN LED
A solid light indicates a connection
on the WAN port. This LED blinks
during data transmission.
Power LED
A solid light indicates a
proper connection to the
power supply.

4
Hardware Overview
LAN Ports
These are the connections for Ethernet cables to
Ethernet-enabled computers.
WAN Port
This is for the connection of an Ethernet
cable to your Cable or DSL modem.
Reset Button
Pressing this button
restores the Router
to its original factory
default settings.
Power Receptor

5
Hardware Installation
Hardware Installation
A. First, connect the power adapter to the receptor at the back panel
of the DIR-100 and then plug the other end of the power adapter
to a wall outlet or power strip. The Power LED will turn ON to
indicate proper operation.
B.1. Power off your Cable or DSL modem; some devices may not
have a on/off switch and will require you to unplug the power
adapter. Now, the DIR-100 should be powered on and the Cable/
DSL modem should be turned off.
2. Cable/DSL modem (Power Off) – DIR-100 (Power On) Connect
an Ethernet cable to the Ethernet jack located on the Cable/DSL
modem. After the Ethernet cable is securely connected, power
on the Cable/DSL modem by turning on the unit or plugging in
the power adapter.
3. Cable/DSL modem (Power On) – DIR-100 (Power On) Insert
the other end of the Ethernet cable to the WAN PORT on the back
panel of the DIR-100. The WAN LED light will illuminate to indicate
proper connection. If the WAN LED is not illuminated, please go
back to step B1 and repeat the instructions.
C.Insert an Ethernet cable to LAN port 1 on the back panel of the
DIR-100 and an available Ethernet port on the network adapter
in the computer you will use to congure the DIR-100. The LED
light for LAN Port 1 will illuminate to indicate proper connection.
Note: The LAN Ports on the DIR-100 are Auto-MDI/MDIX.
Meaning you can use a straight-through or crossover Ethernet
cable to the LAN Ports.
D.Computers equipped with Ethernet or Gigabit Ethernet adapters
will be able to connect to the DIR-100. The DFE-530TX or DGE-
530T PCI Adapters (as examples) will be able to connect with the
router without any additional conguration required.

6
Getting Started
Getting Started

7
Conguration
This section will show you how to congure your new D-Link DIR-100
Router using the D-Link Setup Wizard.
Conguration
Click Log In
Click Setup Wizard
Open your Web browser and type
“http://192.168.0.1” into the URL
address box. Then press the Enter
or Return key.
Type “admin” for the user-
name and leave the pass-
word eld blank.

8
Conguration
Click Next
Click Next
Click Next
You have the option to establish
a password for the User Name
“Admin”.
Choose your time zone from the
drop down list.
Click Setup Wizard

9
Conguration
You will be prompted to select the type of Internet connection for your
router. If you are unsure of which setting to select, please contact
your Internet Service Provider.
PPPoE - page 10
PPTP - page 11
L2TP - page 12
Big Pond - page 13
Static IP Address - page 14
If you selected Dynamic IP Address, this screen will appear: (Used
mainly for Cable Internet service).
Click Next
Dynamic IP Address
Click Next
Continue to page 15
Click the “Clone MAC Address”
button to automatically copy the
MAC address of the network
adapter in your computer. You
can also manually type in the
MAC address.

10
Conguration
PPPoE
Click Next
Click Next
Continue to page 15
Note: Please be sure to remove any existing PPPoE client software
installed on your computers.
If your ISP uses PPPoE
(Point-to-Point Protocol
over Ethernet), select the
corresponding radio button.
If you have a Dynamic IP
connection, enter the User
Name and Password provided
to you by your ISP.