D-Link DSL-1500G v.A1 User manual

1/18
2002/9/13
Console Commands Index and Syntax
DSL-1500G v.A1
SHDSL Router for Annex A
Document Revision: 0.1
Firmware Version: R2.01.b2t7

2/18
2002/9/13
I. Console Comment Utility
The console comment utility of DSL-1500G is HyperTerminal and following is the setup process.
1. Open “HyperTerninal” program
2. Create a new Connection

3/18
2002/9/13
3. The Connect using “Com1”
4. The detail port setting is as below.

4/18
2002/9/13
II. Console Commands Index and Syntax
Commands are:
Command Description
bridge [<command>] - send command to bridge process
buffer [<command>] - send command to buffer process
bun [<command>] - send command to bun process
chips [<command>] - send command to chips process
config [<command>] - send command to config process
dhcpclient [<command>] - send command to dhcpclient process
dhcpserver [<command>] - send command to dhcpserver process
diap [<command>] - send command to diap process
dnsrelay [<command>] - send command to dnsrelay process
edd [<command>] - send command to edd process
ethernet [<command>] - send command to ethernet process
event help|next|previous|recent|show|unshow - control display of events
flashfs [<command>] - send command to ip process
ip_filter [<command>] - send command to ip_filter process
isfs [<command>] - send command to isfs process
nat [<command>] - send command to nat process
oam [<command>] - send command to oam process
oamcli [<command>] - send command to oamcli process
portcli [<command>] - send command to portcli process
ppp [<command>] - send command to ppp process
restart - restart system
shdsl [<command>] - send command to shdsl process
snmp [<command>] - send command to snmp process
tftp [<command>] - send command to tftp process
uptime - show time system has been running
version - show system software version
webserver [<command>] - send command to webserver process

5/18
2002/9/13
Bridge: Command Description
config <command> - configuration commands
device command - Alter bridge configuration
ethertype [<port> "any"|"ip"|"pppoe"] - Set or display forwarded packet types
filter - Display filtering database
filterage [age] - Set or display filter age time
flush [<port>] - Flush filtering database on port(s)
info - Show version
interface command - Process interface command
portfilter [<source port> "all"|<dest ports>] - Set or display ports to forward to
spanning {command} - Control spanning tree operation
Status - Display bridge status
Version - Show version
Buffer: Command Description
List - list the buffer pools
info - [<name>] show [or set] current pool
show - [<n>] show buffer <n> in current pool, or all buffers in use
Steal - <n> steal <n> buffers from current pool, (0 to reset)
Version - display version information for buffer pools
Bun: Command Description
Bun Command ~
help [command] - Display summary of commands
Version - Show software version
Build - Show build information
config <config_spec> - Enter manual configuration request
list config - Display all configuration requests
list devices - Display registered driver devices
list ports - Display registered ports
list channels <port_name> - Display enabled channels on a port

6/18
2002/9/13
Command Description
list all open channels <port_name> - Display all open channels on a port
list spices - Display all available spices
list objects - Display all data objects
show system - Show system attributes
set system - Set system attributes
show device <device_name> ... - Display device information
show port <port_name> - Display port information
show channel <port_name> <channel_number> - Display channel information
set port <port_name> / <attribute> = <value> - Set port attribute
set channel <portname> <channelnumber> /
<attribute> = <value> - Set channel attribute
ethmode <mode> - Display /setting ethernet connect mode
reset port <port_name> - Reset port hardware
list classes - List available port classes
show class <classname> - Show class members
l2filter show - show l2filter rule
l2filter enable <type> - <type> : ipmcast - IP Multicast Packet
pppoe - PPPoE Frame
ip6mcast - IPv6 Multicast Frame
ip_rarp - IP Broadcast and RARP Frame
ipx - IPX Frame
netbeui - NetBEUI Frame
appletalk - AppleTalk Frame
bridge - Bridge Management information
l2filter disable <type> - <type> : ipmcast - IP Multicast Packet
pppoe - PPPoE Frame
ip6mcast - IPv6 Multicast Frame
ip_rarp - IP Broadcast and RARP Frame
ipx - IPX Frame
netbeui - NetBEUI Frame
appletalk - AppleTalk Frame
bridge - Bridge Management information
l2filter save - save configuration to file

7/18
2002/9/13
Command Description
l2filter trace - on/off trace
Ethernet Device ~
ethernet filter - Show NP filter table
Fluorine Driver ~
fluorine address> - Select MII address to read/write
fluorine readr> - Read MII register
fluorine writer> <value> - Read MII register
Chips: Command Description
Cpu - print percentage of cpu cycles used
Debug - enter debug process
Exit - abort from ATMos
Info - print out version information and machine's address
Mem - memory used on a process-by-process basis
Stack - stack usage on a process-by-process basis
rbrb <addr> - read byte at address <addr>
rh <addr> - read halfword at address <addr>
rw <addr> - read word at address <addr>
tell <process> <string> - send string to process using TELL message
wb <addr> <val> - write byte <val> at address <addr>
wh <addr> <val> - write halfword <val> at address <addr>
ww <addr> <val> - write word <val> at address <addr>
Config: Command Description
list - List all modules registered
print [low | medium | high] [<module>] - Print configuration
reset [<module>] - Reset configuration to default
save - Save configuration
resource [<process> [<resource> [<value>]]] - Control resources
default - restore factory default settings
version - Display version information

8/18
2002/9/13
Dhcpclient:
Command Description
config - Displays client configuration file
help - Gives help on available commands
pool - Show DHCP client pool allocation stats
status - Shows status of active lease, or [all] leases
trace - Activates trace option(s)
untrace - Deactivates trace option(s)
version - Show software version
Dhcpserver: Command Description
config - Displays server configuration file and state
help - Gives help on available commands
pool - Show DHCP pool allocation statistics
reset - Reset and restart DHCP server
status - Shows status of server leases
trace - Activates trace option(s)
untrace - Deactivates trace option(s)
version - Display software version
enable - Enable DHCP server Function
disable - Disable DHCP server Function
Diap: Command Description
help - Gives help on available commands
enable - Enable DIAP Function
disable - Disable DIAP Function
passwd - Set DIAP Passwd -- passwd <password>|none
status - Show status of DIAP settings
trace - Activates trace option(s)
untrace - Deactivates trace option(s)
version - Show software version

9/18
2002/9/13
Dnsrelay: Command Description
config - Show DNS relay configuration
help - List help on available commands
retry - Set max number of connection/tx retries
server - Manually specify DNS server IP address
status - Show DNS relay connection status
trace - Activate trace option(s)
untrace - Deactivate trace option(s)
version - Show DNS relay software version
state - enabled | disabled - Enable or Disable or Show state of dnsrelay
pppauto - enabled | disabled - Enable or Disable or Show state of pppauto
Edd: Command Description
event [level] - set event logging level
interface [id] command - process interface command for device id
Status - device status
Version - display driver information
Ethernet: Command Description
event [level] - set event logging level
interface [id] command - process interface command for device id
Status - device status
Version - display driver information
Event: Command Description
event help - show this help
event n|next - show next part of event buffer
event p|previous - show previous part of event buffer
event r|recent - show most recent part of event buffer
event show - enable display of events as they occur

10/18
2002/9/13
Command Description
event unshow - disable display of events as they occur
Flashfs: Command Description
cat <file> - show file contents
config - display flash configuration
fsck - file system check, checks FLASH integrity
id <x> - display chip ID for device x
info - display file system information
ls [-l] - list FLASHFS files [more detail]
rewrite <file> - rewrite boot area with ISFS file <file>
trace [level] - show/set tracing level
update - commit ISFS files to FLASH
configinfo - Show/Set Configuration Info
version - display version number
wipe - irreversibly erase FLASH contents
Ip: Command Description
? syntax ~
help - list commands available
help all - list commands and their syntax
help <command> - list syntax for command
arp syntax ~
arp <cmd> - execute arp subcommand
arp help - list subcommands available
config syntax ~
config [save] - display config or save to flash
device syntax ~
device [list] - list interface definitions
device add <i/f> <type> <file> [mtu <size>]
[<IPaddr>|dhcp] - create interface definition
device delete <i/f> - remove interface definition