D-Link DSR-250 Instruction Manual

Unified Services Router
CLI Reference Guide
Release 1.04
Building Networks for People
http://security.dlink.com
Small Business Gateway Solution
DSR-250 / 250N / 500 / 500N / 1000 / 1000N

CLI Reference Guide
Unified Services Router
D-Link Corporation
Copyright © 2011.
http://www.dlink.com

Unified Services Router CLI Reference Guide
1
CLI Reference Guide
DSR-250/250N/500/500N/1000/1000N
Unified Services Router
Version 1.04
Copyright © 2011
Copyright Notice
This publication, including all photographs, illustrations and software, is protected under
international copyright laws, with all rights reserved. Neither this manual, nor any of the
material contained herein, may be reproduced without written consent of the author.
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes
no representations or warranties with respect to the contents hereof and specifically disclaim
any implied warranties of merchantability or fitness for any particular purpose. The
manufacturer reserves the right to revise this publication and to make changes from time to
time in the content hereof without obligation of the manufacturer to notify any person of such
revision or changes.
Limitations of Liability
UNDER NO CIRCUMSTANCES SHALL D-LINK OR ITS SUPPLIERS BE LIABLE FOR
DAMAGES OF ANY CHARACTER (E.G. DAMAGES FOR LOSS OF PROFIT, SOFTWARE
RESTORATION, WORK STOPPAGE, LOSS OF SAVED DATA OR ANY OTHER
COMMERCIAL DAMAGES OR LOSSES) RESULTING FROM THE APPLICATION OR
IMPROPER USE OF THE D-LINK PRODUCT OR FAILURE OF THE PRODUCT, EVEN IF
D-LINK IS INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. FURTHERMORE, D-
LINK WILL NOT BE LIABLE FOR THIRD-PARTY CLAIMS AGAINST CUSTOMER FOR
LOSSES OR DAMAGES. D-LINK WILL IN NO EVENT BE LIABLE FOR ANY DAMAGES
IN EXCESS OF THE AMOUNT D-LINK RECEIVED FROM THE END-USER FOR THE
PRODUCT.

Unified Services Router CLI Reference Guide
2
Table of Contents
Chapter 1. Introduction.............................................................................................................................7
1.1 Accessing the CLI.....................................................................................................7
Chapter 2. Basic commands available on the CLI ...............................................................................8
2.1 CONTEXT SENSITIVE HELP.................................................................................8
2.2 AUTO-COMPLETION ..............................................................................................8
2.3 MOVEMENT KEYS ..................................................................................................8
2.4 DELETION KEYS .....................................................................................................8
2.5 ESCAPE SEQUENCES...........................................................................................9
Chapter 3. Command Hierarchy in CLI................................................................................................10
3.1 CLI commands can be divided into 4 categories: ..............................................10
3.2 The router configuration is divided into 5 branches:..........................................10
Chapter 4. Global commands used in CLI...........................................................................................11
Chapter 5. Show commands used in CLI............................................................................................12
Chapter 6. Utility commands used in CLI ............................................................................................15
6.1 util ping <ip_address>............................................................................................15
6.2 util system_check capturePackets.......................................................................15
6.3 util system_check....................................................................................................15
6.4 util system_check dns_lookup..............................................................................15
6.5 util system_check traceroute.................................................................................15
Chapter 7. Configure commands used in CLI.....................................................................................17
Chapter 8. Configuration commands under branch NET..................................................................22
8.1 net bandwidth profile enable .................................................................................22
8.2 net bandwidth profile add/edit...............................................................................22
8.3 net bandwidth profile delete <row_id>.................................................................22
8.4 net ddns configure ..................................................................................................22
8.5 net ipv6_tunnel isatap add/edit.............................................................................23
8.6 net ipv6_tunnel isatap delete <row_id>...............................................................23
8.7 net ipv6_tunnel six_to_four configure..................................................................23
8.8 net lan dhcp reserved_ip add................................................................................24
8.9 net lan dhcp reserved_ip delete <mac_address>..............................................24
8.10 net lan group add <name> ....................................................................................24
8.11 net lan group delete <name>................................................................................24
8.12 net lan host add/edit...............................................................................................24
8.13 net lan host delete <row_id>.................................................................................25
8.14 net lan ipv4 configure .............................................................................................25
8.15 net lan ipv6 configure .............................................................................................25
8.16 net lan ipv6 pool configure <start_address>.......................................................26

Unified Services Router CLI Reference Guide
3
8.17 net lan ipv6 pool delete <start_address> ............................................................26
8.18 net mode configure.................................................................................................26
8.19 net port management configure <port_name>...................................................27
8.20 net radvd configure.................................................................................................27
8.21 net radvd pool add/edit...........................................................................................28
8.22 net radvd pool delete <row_id> ............................................................................28
8.23 net routing dynamic configure...............................................................................28
8.24 net routing mode configure....................................................................................30
8.25 net routing static ipv4 configure <name> ............................................................30
8.26 net routing static ipv4 delete <name>..................................................................31
8.27 net routing static ipv6 configure <name> ............................................................31
8.28 net routing static ipv6 delete <name>..................................................................32
8.29 net upnp configure..................................................................................................32
8.30 net wan mode configure.........................................................................................32
8.31 net wan configurable_port configure....................................................................34
8.32 net wan wan1 ipv4 configure.................................................................................34
8.33 net wan wan2 ipv4 configure.................................................................................36
8.34 net wan wan3 threeG configure............................................................................37
8.35 net wan wan1-pppoeprofile add prof_name .......................................................38
8.36 net wan wan2-pppoeprofile add prof_name .......................................................39
8.37 net wan wan1-pppoeprofile edit prof_name........................................................40
8.38 net wan wan2-pppoeprofile edit prof_name........................................................40
8.39 net wan wan1-pppoeprofile delete prof_name...................................................41
8.40 net wan wan2-pppoeprofile delete prof_name...................................................41
8.41 net wan1 ipv6 configure.........................................................................................41
8.42 net wan wan2 ipv6 configure.................................................................................42
8.43 net routing protocol_binding add/edit...................................................................43
8.44 routing protocol_binding enable <row_id>..........................................................43
8.45 routing protocol_binding edit.................................................................................44
8.46 routing protocol_binding disable...........................................................................44
8.47 ddns wan2 configure DDNS configuration mode..............................................44
8.48 dmz dhcp reserved_ip............................................................................................44
Chapter 9. Configuration commands under branch SECURITY......................................................45
9.1 security attack_checks configure..........................................................................45
9.2 security blocked_keywords add/edit ....................................................................45
9.3 security blocked_keywords delete <row_id>......................................................46
9.4 security blocked_keywords disable <row_id> ....................................................46
9.5 security blocked_keywords enable <row_id>.....................................................46
9.6 security content_filtering configure.......................................................................46
9.7 security custom_service add/edit .........................................................................46
9.8 security custom_service delete <row_id> ...........................................................47
9.9 security firewall ipv4 default_outbound_policy ...................................................47

Unified Services Router CLI Reference Guide
4
9.10 security firewall ipv4 configure/edit.......................................................................47
9.11 security firewall ipv4 delete <row_id>..................................................................48
9.12 security firewall ipv4 disable <row_id> ................................................................49
9.13 security firewall ipv4 enable ..................................................................................49
9.14 security ids configure..............................................................................................49
9.15 security ip_or_mac_binding add/edit ...................................................................49
9.16 security ip_or_mac_binding delete <row_id> .....................................................50
9.17 security port_triggering add/edit ...........................................................................50
9.18 security port_triggering delete <row_id> .............................................................50
9.19 security schedules add/edit...................................................................................51
9.20 security schedules delete <row_id>.....................................................................51
9.21 security session_settings configure .....................................................................51
9.22 security mac_filter source add/edit.......................................................................52
9.23 security mac_filter source delete <row_id>.........................................................52
9.24 security mac_filter configure..................................................................................52
9.25 security trusted_domain add/edit..........................................................................53
9.26 security trusted_domain delete.............................................................................53
9.27 security vpn_passthrough configure ....................................................................53
9.28 security firewall ipv4 configure..............................................................................53
Chapter 10. Configuration commands under branch SYSTEM..........................................................55
10.1 system logging facility configure <facility>..........................................................55
10.2 system logging ipv4 configure...............................................................................55
10.3 system logging remote configure..........................................................................56
10.4 system radius configure <radiusServer>.............................................................57
10.5 system radius delete <radiusServer> ..................................................................57
10.6 system remote_management https configure ....................................................57
10.7 system snmp sys configure...................................................................................58
10.8 system snmp trap configure <agentIp> ...............................................................58
10.9 system snmp trap delete <agentIp>.....................................................................58
10.10 system snmp user configure .................................................................................59
10.11 system time configure ............................................................................................60
10.12 system traffic_meter configure..............................................................................61
10.13 system group add ...................................................................................................62
10.14 system group edit <row_id>..................................................................................62
10.15 system group delete <row_id>..............................................................................62
10.16 system users add....................................................................................................62
10.17 system users edit <row_id>...................................................................................63
10.18 system users delete <row_id>..............................................................................63
10.19 system users password <user>............................................................................63
10.20 system usb usb1 configure....................................................................................63
10.21 system usb usb2 configure....................................................................................63
Chapter 11. Configuration commands under branch DOT11 .............................................................64

Unified Services Router CLI Reference Guide
5
11.1 dot11 access point configure <ap_name>..........................................................64
11.2 dot11 access point delete <ap_name>................................................................64
11.3 dot11 access point disable <ap_name>..............................................................65
11.4 dot11 access point enable <ap_name>...............................................................65
11.5 dot11 access point mac add <ap_name> <mac_address>..............................65
11.6 dot11 access point mac delete <ap_name> <mac_address> .........................65
11.7 dot11 profile configure <profile_name>...............................................................65
11.8 dot11 radio advanced configure <radio_num>...................................................66
11.9 dot11 radio configure <radio_num>.....................................................................67
Chapter 12. Configuration commands under branch VPN..................................................................68
12.1 vpn ipsec policy connect <row_id>.......................................................................68
12.2 vpn ipsec policy drop <row_id> ............................................................................68
12.3 vpn ipsec policy delete <name>..........................................................................68
12.4 vpn ipsec policy configure <name>.....................................................................68
12.5 vpn ipsec policy disable <name>..........................................................................73
12.6 vpn ipsec policy enable <name>..........................................................................73
12.7 vpn ipsec dhcp configure.......................................................................................74
12.8 vpn sslvpn client......................................................................................................74
12.9 vpn sslvpn policy add/edit......................................................................................74
12.10 vpn sslvpn policy delete <row_id>........................................................................75
12.11 vpn sslvpn portal-layouts add/edit........................................................................75
12.12 vpn sslvpn portal-layouts delete <row_id>..........................................................75
12.13vpn sslvpn portforwarding appconfig add............................................................76
12.14 vpn sslvpn portforwarding appconfig delete <row_id>......................................76
12.15 vpn sslvpn portforwarding hostconfig add...........................................................76
12.16 vpn sslvpn portforwarding hostconfig delete <row_id>.....................................76
12.17 vpn sslvpn resource add........................................................................................76
12.18 vpn sslvpn resource delete <row_id> ..................................................................77
12.19 vpn sslvpn resource configure add <resource_name>.....................................77
12.20 vpn sslvpn resource configure delete <row_id> <resource_name>................77
12.21 vpn sslvpn route add ..............................................................................................77
12.22 vpn sslvpn route delete <row_id>.........................................................................78
12.23 vpn sslvpn users domains add..............................................................................78
12.24 vpn sslvpn users domains edit <domainname>.................................................79
12.25 vpn sslvpn users domains delete <domainname>.............................................80
12.26 vpn sslvpn users users login_policies <user_row_id> ......................................80
12.27 vpn sslvpn users users ip_policies configure <user_row_id>..........................80
12.28 vpn sslvpn users users ip_policies delete <row_id>..........................................81
12.29 vpn sslvpn users users browser_policies <user_row_id>.................................81

Unified Services Router CLI Reference Guide
6

Unified Services Router CLI Reference Guide
7
Chapter 1. Introduction
This document describes the command line interface (CLI) for managing D-Link's DSR-
1000N/1000/500N/500/250N/250 series of routers.
The CLI user requires advanced knowledge about the configuration of the system and should be
used only by those users who are familiar with CLI-based configuration.
Note that the following features in the DSR Unified Services Router cannot be managed
by the CLI: Firmware Upgrade
Configuration Backup / Restore
Certificate Generate / Upload
Power Savings mode configuration
System Dashboard / Resource Utilization
Please access the web browser based UI of the DSR router for managing these features.
1.1 Accessing the CLI
The CLI can be accessed by logging in with the same user credentials as used to
access the web browser based UI.
********************************************
Welcome to the DSR Command Line Interface
********************************************
D-Link DSR>
Note: D-Link DSR> is the CLI prompt.
RIP, WAN2, DMZ, Captive Portal related commands are not available on DSR-
250N/250.
Wireless related commands are available on DSR-1000N, DSR-500N and DSR-
250N only.

Unified Services Router CLI Reference Guide
8
Chapter 2. Basic commands available
on the CLI
2.1 CONTEXT SENSITIVE HELP
[?] - Display context sensitive help. This is either a list of possible command
completions with summaries, or the full syntax of the current command. A subsequent
repeat of this key, when a command has been resolved, will display a detailed
reference.
2.2 AUTO-COMPLETION
The following keys both perform auto-completion for the current command line. If the
command prefix is not unique a subsequent repeat of the key will display possible
completions.
[enter] - Auto-completes, syntax-checks then executes a command. If there is a
syntax error then offending part of the command line will be highlighted and
explained.
[space] - Auto-completes, or if the command is already resolved, inserts a
space.
2.3 MOVEMENT KEYS
[CTRL-A] - Move to the start of the line.
[CTRL-E] - Move to the end of the line.
[up] - Move to the previous command line held in history.
[down] - Move to the next command line held in history.
[left] - Move the insertion point left one character.
[right] - Move the insertion point right one character.
2.4 DELETION KEYS
[CTRL-C] - Delete the whole line.
[CTRL-D] - Delete the character to the right on the insertion point.
[CTRL-K] - Delete all the characters to the right of the insertion point.
[Backspace] - Delete the character to the left of the insertion point.

Unified Services Router CLI Reference Guide
9
2.5 ESCAPE SEQUENCES
!! - Substitute the last command line.
!N - Substitute the Nth command line (absolute as per 'history' command).
!-N - Substitute the command line entered N lines before (relative).

Unified Services Router CLI Reference Guide
10
Chapter 3. Command Hierarchy in CLI
3.1 CLI commands can be divided into 4
categories:
Global commands
Show commands
Utility commands
Configuration commands
3.2 The router configuration is divided into 5
branches:
Net: Network Settings
Security: Security Settings
System: Admin Settings
Dot11: Wireless Settings
Vpn: VPN Settings

Unified Services Router CLI Reference Guide
11
Chapter 4. Global commands used in
CLI
.exit: Exit this session
.help: Display an overview of the CLI syntax
.top: Return to the default mode
.reboot: Reboot the system.
.history: Display the current session's command line history. Number of commands
in history list can be controlled by setting limit argument; by default it is
unbounded.

Unified Services Router CLI Reference Guide
12
Chapter 5. Show commands used in
CLI
The show commands for all the above mentioned branches are outlined in this section.
The command show net ? at the CLI prompt would give the description of all the show
commands in the branch net, which is as follows:
Sl No
Command Name
Purpose
1
show net available_lan_host list
Display available lan host list
2
show net bandwidth profile setup
Display bandwidth profile configuration
3
show net ddns setup
Display ddns configuration
4
show net dhcp leased_clients list
Display dhcp leased clients list
5
show net dhcp reserved_ip setup
Display dhcp reserved ip configuration
6
show net routing dynamic setup
Display dynamic routing configuration
7
show net mode setup
Display network mode configuration
8
show net ipv6_tunnel setup
Display ipv6 tunnel’s configuration
9
show net lan ipv4 setup
Display ipv4 lan configuration
10
show net port management setup
Display port management configuration
11
show net radvd setup
Display radvd configuration
12
show net routing mode setup
Display routing mode configuration
13
show net routing static ipv4 setup
Display ipv4 static routes configuration
14
show net routing static ipv6 setup
Display ipv6 static routes configuration
15
show net statistics
Display network statistics
16
show net bandwidth traffic_selector setup
Display bandwidth traffic selector configurations
17
show net upnp portmap
Display upnp portmap
18
show net upnp setup
Display upnp configuration
19
show net wan wan1 ipv4 setup
Display ipv4 wan1 configuration
20
show net wan wan1 ipv4 status
Display ipv4 wan1 connection status
21
show net wan wan2 ipv4 setup
Display ipv4 wan2 configuration
22
show net ddns setup
Display ddns configuration for dedicated WAN and
configurable WAN
23
show net routing protocol_binding setup
Display protocol binding configuration
24
show net dmz dhcp reserved_ip setup
Display dhcp reserved ip configuration

Unified Services Router CLI Reference Guide
13
The command show security ? at the CLI prompt would give the description of all the show
commands in the branch security, which is as follows:
Sl No
Command Name
Purpose
1
show security attack_checks setup
Display Security Checks configuration
2
show security blocked_keywords setup
Display blocked keywords configuration
3
show security content_filtering setup
Display content filtering configuration
4
show security custom_service setup
Display Custom Service configuration
5
show security firewall ipv4 setup
Display Firewall Rules
6
show security firewall ipv6 setup
Display Firewall Rules
7
show security ids setup
Display IDS configuration
8
show security ip_or_mac_binding setup
Display IP/MAC Binding configuration
9
show security port_triggering setup
Display Port Triggering configuration
10
show security schedules setup
Display Schedules configuration
11
show security session_settings
Display Session Settings configuration
12
show security mac_filter setup
Display Source Mac Filter configuration
13
show security trusted_domains setup
Display trusted domains configuration
14
show security vpn_passthrough setup
Display VPN passthrough Configuration
The command show system ? at the CLI prompt would give the description of all the show
commands in the branch system, which is as follows:
Sl No
Command Name
Purpose
1
show system logging ipv6 setup
Display logging configuration
2
show system logging facility setup
Display logging facility configuration
3
show system logging ipv4 setup
Display logging configuration
4
show system radius setup
Display radius configuration
5
show system logging remote setup
Display remote logging configuration
6
show system remote_management setup
Display Remote Management configuration
7
show system snmp setup
Display snmp configuration
8
show system status
Display system status
9
show system time setup
Display timezone and ntp configuration
10
show system traffic_meter setup
Display traffic meter configuration
The command show dot11 ? at the CLI prompt would give the description of all the show
commands in the branch dot11, which is as follows:
Sl No
Command Name
Purpose
1
show dot11 access point setup [ap_name]
Display access point configuration
2
Show dot11 radio setup
Display radio configuration

Unified Services Router CLI Reference Guide
14
Sl No
Command Name
Purpose
3
Show dot11 profile setup [profile_name]
[display_qos]
Display profile configuration
The command show vpn ? at the CLI prompt would give the description of all the show
commands in the branch vpn, which is as follows:
Sl No
Command Name
Purpose
1
show vpn ipsec dhcp setup
Show DHCP setup
2
show vpn ipsec policy setup
Show list of ipsec policies
3
show vpn ipsec policy status
Show the status of policies
4
show vpn sslvpn client
Show SSLVPN client settings
5
show vpn sslvpn policy
Show SSLVPN policy settings
6
show vpn sslvpn portal-layouts
Show SSLVPN portal layout settings
7
show vpn sslvpn portforwarding appconfig
Show SSLVPN port forwarding application configuration
8
show vpn sslvpn portforwarding hostconfig
Show SSLVPN port forwarding host configuration
9
show vpn sslvpn resource
Show SSLVPN resource settings
10
show vpn sslvpn resource-object
Show SSLVPN resource objects
11
show vpn sslvpn route
Show SSLVPN configured client routes
12
Show vpn sslv[n users users
Show List of Users
13
show vpn sslvpn users domains
Show List od Domains
14
show vpn sslvpn users groups
Show List of Groups
15
show vpn sslvpn users browser_policies
Show List of Browser Policies
16
show vpn sslvpn users ip_policies
Show List of IP Policies
17
show vpn sslvpn users login_policies
Show List of Login Policies

Unified Services Router CLI Reference Guide
15
Chapter 6. Utility commands used in
CLI
The command util ? at the CLI prompt would give the description of all the utility commands in
the branch util, which is as follows:
Sl No
Command Name
Purpose
1
util ping
Ping or Trace an IP Address.
2
util restore_factory_defaults
Revert to factory default settings.
3
util reboot
Reboot the system
6.1 util ping <ip_address>
Sl No
Command Name
Description
Type and Description
1
ip_address
Ping target IP address.
IP Address,
Ping target IP address.
6.2 util system_check capturePackets
Sl No
Command Name
Description
Type and Description
1
download
Download the packet capture to the
host machine
Download the packet capture to the
host machine
2
Start
Start the packet capture
Specify the interface (WAN1,
WAN2 and LAN)
3
Stop
Stop the packet capture
6.3 util system_check
Sl No
Command Name
Description
Type and Description
1
display_IPV4_routingtable
Display IPV4 Routing Table
Display IPV4 Routing Table
6.4 util system_check dns_lookup
Sl No
Command Name
Description
Type and Description
1
dns
Internet name
String
IP address
DNS
6.5 util system_check traceroute
Sl No
Command Name
Description
Type and Description
1
ip_address
It displays all the routers present
String

Unified Services Router CLI Reference Guide
16
Sl No
Command Name
Description
Type and Description
between the destination IP address and
this router
IP address

Unified Services Router CLI Reference Guide
17
Chapter 7. Configure commands used
in CLI
The configure commands for all the branches mentioned above are discussed in this section.
The command net ? at the CLI prompt would give the description of all the configuration
commands in the branch net, which is as follows:
Sl No
Command Name
Purpose
1
net bandwidth profile add
It allows to add a bandwidth profile.
2
net bandwidth profile edit
It allows to edit a bandwidth profile.
3
net bandwidth profile delete
It allows to delete a bandwidth profile.
4
net ddns configure
Ddns configuration mode
5
net routing dynamic configure
Dynamic routing configuration mode
6
net mode configure
IP Mode configuration mode
7
net ipv6_tunnel isatap add
Isatap tunnel configuration mode.
8
net ipv6_tunnel isatap delete
Delete the configured isatap tunnel
9
net ipv6_tunnel isatap edit
Isatap tunnel configuration mode.
10
net ipv6_tunnel six_to_four automatic_tunneling
enable
Six to four tunnel configuration mode
11
net lan dhcp reserved_ip add
Dhcp reserved ip configuration mode
12
net lan dhcp reserved_ip delete
Delete the configured dhcp reserved ip
13
net lan ipv4 configure
Lan configuration mode
14
net lan ipv6 configure
Lan configuration mode
15
net lan ipv6 pool configure
Ipv6 pool configuration mode
17
net mld configure
MLD configuration mode
18
net port management configure
Port management configuration mode
19
net radvd configure
Radvd configuration mode
20
net radvd pool add
Radvd pool configuration add mode
21
net radvd pool delete
Radvd pool configuration delete mode
22
net radvd pool edit
Radvd pool configuration edit mode
23
net routing mode configure
Routing mode configuration
24
net routing static ipv4 configure
Static route configuration mode
25
net routing static ipv4 delete
Static route configuration delete mode
26
net routing static ipv6 configure
Static route configuration mode
27
net routing static ipv6 delete
Static route configuration delete mode
28
net bandwidth traffic_selector add
Traffic selector configuration mode

Unified Services Router CLI Reference Guide
18
Sl No
Command Name
Purpose
29
net bandwidth traffic_selector edit
Traffic selector configuration edit mode
30
net bandwidth traffic_selector delete
Traffic selector configuration delete mode
31
net upnp configure
Upnp configuration mode
32
net wan wan1 ipv4 configure
Wan1 ipv4 configuration mode
33
net wan ipv6 configure
Wan ipv6 configuration mode
34
net wan wan2 ipv4 configure
Wan2 ipv4 configuration mode
35
net wan wan1-pppoeprofile
Wan1 profile configuration mode
36
net wan wan2-pppoeprofile
Wan2 profile configuration mode
The command security ? at the CLI prompt would give the description of all the configuration
commands in the branch security, which is as follows:
Sl No
Command Name
Purpose
1
security attack_checks configure
security checks configuration mode.
2
security blocked_keywords add
blocked Keyword configuration mode.
3
security blocked_keywords disable
blocked Keyword configuration mode.
4
security blocked_keywords delete
blocked Keyword configuration mode.
5
security blocked_keywords edit
blocked Keyword configuration mode.
6
security blocked_keywords enable
blocked Keyword configuration mode.
7
security content_filtering configure
content filtering configuration mode.
8
security custom_service add
custom service configuration mode.
9
security custom_service delete
custom service configuration mode.
10
security custom_service edit
custom service configuration mode.
11
security firewall ipv4 default_outbound_policy
enable
Firewall Settings, Default Outbound Policy configuration
mode.
12
security firewall ipv6 default_outbound_policy
enable
Firewall Settings, Default Outbound Policy configuration
mode.
13
security firewall ipv4 configure
Firewall IPV4 rules configuration mode.
14
security firewall ipv4 delete
Firewall IPV4 rules configuration mode.
15
security firewall ipv4 disable
Firewall IPV4 rules configuration mode.
16
security firewall ipv4 edit
Firewall IPV4 rules configuration mode.
17
security firewall ipv4 enable
Firewall IPV4 rules configuration mode.
18
security firewall ipv6 configure
Firewall IPV6 rules configuration mode.
19
security firewall ipv6 delete
Firewall IPV6 rules configuration mode.
20
security firewall ipv6 disable
Firewall IPV6 rules configuration mode.
21
security firewall ipv6 edit
Firewall IPV6 rules configuration mode.
22
security firewall ipv6 enable
Firewall IPV6 rules configuration mode.