D-Link SecuriCam DCS-6510 User manual

This document will guide you through the basic installation
process for your new D-Link Network Camera.
DCS-6510
Documentation also available on
CD and via the D-Link Website
Quick Installation Guide
Day & Night Vandal-Proof Fixed Dome Network Camera
Quick Installation Guide
Руководство по быстрой установке
Guía de Instalación Rápida
Guia de Instalação Rápida
快速安裝指南
Petunjuk Pemasangan Cepat
クイックインストールガイド

D-Link DCS-6510 Quick Install Guide 1
ENGLISH
DCS-6510 Quick Install Guide
This installation guide provides basic instructions for installing the DCS-6510 Network
Camera on your network. For additional information about how to use the camera,
please see the User’s Manual which is available on the CD included in this package or
from the D-Link support website.
Installation Steps
1. Verify the package contents against the list below.
2. Hardware Overview
3. SD Card Installation
4. Hardware Installation
5. Conguration with Wizard
6. Adjusting the Zoom/Focus
1. Package Contents
DCS-6510 Network Camera
Manual and Software on CD-ROM
Power Adapter
Quick Install Guide
Screwdriver
If any of the above items are missing, please contact your reseller.
Safety Notice:
Installation and servicing should be done by certied technicians so as to conform to all
local codes and prevent voiding your warranty.

D-Link DCS-6510 Quick Install Guide
2
ENGLISH
2. Hardware Overview
Infrared LEDs
Used to illuminate the camera's
eld of view at night
Camera Lens
DC iris varifocal lens
BNC Connector
Analog video output
Power Connector
Connects to 12 V DC power
Power Wiring
Connects to 24 V AC power
Ethernet Jack
RJ-45 connector for Ethernet
which can also be used to
power the camera using Power
over Ethernet (PoE)
Audio Wiring
Audio Input / Output
DI/DO Wiring
I/O connectors for external devices
Vandal-Proof Cover
Protects the camera from
damage
Install the SD Card
Push the SD card into the camera with the
gold contacts oriented towards the base of
the camera. To eject the SD card, push the
SD card into the slot.
3. SD Card Installation
Disassemble the Camera
Open the camera enclosure by removing
the 4 screws. Lift the dome off the base of
the camera.

D-Link DCS-6510 Quick Install Guide 3
ENGLISH
4. Hardware Installation
Mounting Installation
Please see the User Manual for detailed instructions regarding installation and mounting
of the camera using a mounting bracket.
Flush Mount (DCS-33-1)
Inner Mounting Ring
Ceiling
Recessed
Bracket
Plastic
Ring
Dome
Camera
Tether
Height: 60 mm (2.36 inches)
Diameter: 190 mm (7.48 inches)
Weight: 272.5 g (0.60 lbs)

D-Link DCS-6510 Quick Install Guide
4
ENGLISH
Plastic
Ring
Surface
Bracket
Ceiling
Dome
Camera
Surface Mount (DCS-33-2)
Tether
Height: 25 mm (0.98 inches)
Diameter: 190 mm (7.48 inches)
Weight: 167.5 g (0.36 lbs)

D-Link DCS-6510 Quick Install Guide 5
ENGLISH
Pendant Mount (DCS-33-3)
Suspension
Bracket
Bracket
Cap
Tether
Dome
Camera
Height: 201 mm (7.91 inches)
Diameter: 150 mm (5.90 inches)
Weight: 534.7 g (1.17 lbs)

D-Link DCS-6510 Quick Install Guide
6
ENGLISH
Bent Mount (DCS-33-4)
Bracket
Cap
Tether
Dome
Camera
Bent
Bracket
Height: 253 mm (9.96 inches)
Diameter: 150 mm (5.90 inches)
Weight: 640.7 g (1.41 lbs)

D-Link DCS-6510 Quick Install Guide 7
ENGLISH
Connection with a PoE Hub
If you are using a PoE hub, connect the IP camera to the hub via an Ethernet cable,
which will provide transmission of both power and data over a single cable.
General Connection Using 24 V AC Power Wiring
1. Connect the network camera to a hub via an Ethernet cable.
2. Connect the supplied power cable from the camera to a power source such as your
building's emergency power.
General Connection Using 12 V DC Power Adapter
1. Connect the network camera to a hub via an Ethernet cable.
2. Connect the supplied power cable from the camera to a power outlet.

D-Link DCS-6510 Quick Install Guide
8
ENGLISH
5. Conguration with Wizard
Click Setup Wizard to begin the installation.
Insert the DCS-6510 CD into your computer's CD-ROM drive to begin the installation. If
the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start
automatically, click Start > Run. Type D:\autorun.exe, where D: represents the drive
letter of your CD-ROM drive.
After clicking Setuop Wizard, the following window will
open.
Click Next to continue.
Click Yes to accept the License Agreement.
Click Finish to complete the installation.
To start the installation process, click Next.
Note: The installation may take several minutes to
nish.