D-Link DXS-3410 Series Manual

Version 1.00 | 2023/12/18

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
ii
Information in this document is subject to change without notice. Reproduction in any manner whatsoever, without the written
permission of D-Link Corporation, is strictly forbidden.
Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are
registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or
their products. D-Link Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
© 2024 D-Link Corporation. All rights reserved.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
CE Mark Warning
This equipment is compliant with Class A of CISPR 32. In a residential environment, this equipment may cause radio interference.
Avertissement Concernant la Marque CE
Cet équipement est conforme à la classe A de la norme CISPR 32. Dans un environnement résidentiel, cet équipement peut
provoquer des interférences radio.
VCCI Warning
この装置は、クラス A機器です。この装置を住宅環境で使用すると電波妨害を引き起こすことがあります。この場合には使用者が
適切な対策を講ずるよう要求されることがあります。 VCCI-A
BSMI Notice
警告: 為避免電磁干擾，本產品不應安裝或使用於住宅環境。
Safety Compliance
Warning: Class 1 Laser Product: When using a fiber optic media expansion module, never look at the transmit laser while it is
powered on. In addition, never look directly at the fiber TX port and fiber cable ends when they are powered on.
Avertissement: Produit Laser de Classe 1: Ne regardez jamais le laser tant qu’il est sous tension. Ne regardez jamais
directement le port TX (Transmission) à fibres optiques et les embouts de câbles à fibres optiques tant qu’ils sont sous tension.

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
iii
Table of Contents
Intended Readers .............................................................................................................................................v
Typographical Conventions...............................................................................................................................v
Notes and Cautions...........................................................................................................................................v
1. Introduction.....................................................................................................................................................1
Switch Description ............................................................................................................................................1
Switch Series....................................................................................................................................................1
Package Contents.............................................................................................................................................1
2. Hardware Components...................................................................................................................................2
Front Panel Components ..................................................................................................................................2
Front Panel LED Indicators ..........................................................................................................................3
Rear Panel Components...................................................................................................................................5
Side Panel Components....................................................................................................................................6
3. Installation.......................................................................................................................................................7
Installation Guidelines.......................................................................................................................................7
Installing the Switch without a Rack...................................................................................................................7
Installing the Switch in a Standard 19" Rack......................................................................................................8
Installing Transceivers into the Transceiver Ports..............................................................................................9
Connecting AC Power to the Switch................................................................................................................10
Installing the AC Power Cord Retainer .......................................................................................................10
Installing the Redundant Power Supply (RPS).................................................................................................12
Connecting the DPS-500A RPS to the Switch ............................................................................................12
4. Switch Connections......................................................................................................................................14
Stacking the Switch.........................................................................................................................................14
Switch to Switch..............................................................................................................................................17
Switch to End Node.........................................................................................................................................17
5. Switch Management......................................................................................................................................19
Management Options......................................................................................................................................19
Command Line Interface (CLI) ........................................................................................................................19
Connecting to the Console Port..................................................................................................................19
Logging into the CLI...................................................................................................................................20
Configuring the IP Address.........................................................................................................................20
Web User Interface (Web UI)..........................................................................................................................21
Connecting to the Web UI ..........................................................................................................................21
Logging into the Web UI.............................................................................................................................21
SNMP-based Management.............................................................................................................................23
Connecting using SNMP............................................................................................................................23
Traps.........................................................................................................................................................23
Management Information Base (MIB).........................................................................................................23
Appendix A - Technical Specifications..................................................................................................................24
Appendix B - Cables and Connectors....................................................................................................................28
Ethernet Cable................................................................................................................................................28
Console Cable ................................................................................................................................................29
Appendix C - ERPS Information.............................................................................................................................30
Safety/Sécurité........................................................................................................................................................31
Safety Instructions ..........................................................................................................................................31
Safety Cautions..........................................................................................................................................31
Consignes de sécurité.....................................................................................................................................32

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
iv
Précautions de sécurité..............................................................................................................................32
General Precautions for Rack-Mountable Products .........................................................................................34
Protecting Against Electrostatic Discharge ......................................................................................................35
Warranty & Technical Support ..............................................................................................................................36

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
v
Intended Readers
This guide provides comprehensive information regarding the hardware specifications of the switches in this series. It
offers concise instructions on configuring and managing switches within this series. This manual is designed for
advanced-level users who possess familiarity with network management concepts and terminology. For practical
purposes, all switches within this series will be consistently referred to as the "Switch" throughout this manual.
Typographical Conventions
Convention
Description
Boldface Font
This convention is used to emphasize keywords.
It also denotes a button, toolbar icon, menu, or menu items.
For example, click the Apply button.
Initial capital letter
This convention is used to indicate a window name or keyboard key.
For example, press the Enter key.
Blue Courier Font
This convention is used to represent a CLI example.
Notes and Cautions
NOTE: A note indicates important information that helps you make better use of your device.
CAUTION: A caution indicates a potential for property damage, personal injury, or death.
ATTENTION :Une précaution indique un risque de dommage matériel, de blessure corporelle ou de
mort.

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
1
1. Introduction
Switch Description
Introducing the DXS-3410 series, D-Link's latest evolution of Managed switches. This series offers an extensive range
of port types and speeds, facilitating seamless interconnection among diverse networking devices for effective
communication. Leveraging SFP28 and SFP+ ports with fiber-optic cabling, these switches enable high-performing
uplink connections, bridging considerable distances.
Moreover, the DXS-3410 series incorporates D-Link's forward-thinking third-generation Green Ethernet technology
(IEEE 802.3az). This innovation conserves power by deactivating LEDs according to a personalized schedule for
inactive links and by allowing ports to autonomously enter a hibernated state. This intelligent approach ensures
efficiency and sustainability.
Switch Series
The following switches are part of the DXS-3410 series:
DXS-3410-32XY - A stackable Layer 3 managed switch with 24 x 10GbE RJ45 ports, 4 x 10GbE SFP+ ports,
and 4 x 25GbE SFP28 ports.
DXS-3410-32SY - A stackable Layer 3 managed switch with 28 x 10GbE SFP+ ports and 4 x 25GbE SFP28
ports.
Package Contents
Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following
items:
One DXS-3410 series switch
One AC power cord
One AC power cord retainer set
One RJ45 to RS-232 console cable
Four rubber feet with adhesive backing
One rack mounting kit, containing two brackets and a number of screws
One quick installation guide
NOTE: If any item is missing or damaged, please contact your local D-Link reseller for replacement.

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
2
2. Hardware Components
Front Panel Components
This following table lists the front panel components on all the switches in the series:
Port
Description
Reset/ZTP
The Reset button can be used to (1) reboot the switch, (2) start the ZTP function,
or (3) reset the switch to its factory default settings depending on how long this
button is pressed.
Zero-Touch Provisioning (ZTP) is an automated network deployment and
configuration process that eliminates manual intervention by allowing devices to be
discovered, provisioned, and configured automatically upon connection to the
network.
Push Time
Description
< 5 sec
The Switch reboots after the button is released.
5 to 10 sec
All green LEDs on the ports remain continuously lit before the
button is released. Once the button is released, the LEDs
change to a blinking state, initiating the ZTP function, and then
the device reboots.
> 10 sec
All amber LEDs on the ports stay continuously lit before the
button is released. After the button is released, the Switch will
reboot and reset the system to its factory defaults.
USB Port
The USB port provides additional storage space for firmware images and
configuration files that can be copied to and from the Switch. Only endpoint
devices like USB flash drives are supported.
Console Port
The console port can be used to connect to the CLI of the Switch. This Out-Of-
Band (OOB) connection can be made from the serial port of an administrative node
to the RJ45 console port on the front panel of the Switch. The console cable
(included in the package) must be used for the connection.
MGMT Port
The management (MGMT) port can be used to connect to the CLI or the Web UI of
the Switch. SNMP-enabled connectivity can also be made through this port. This
OOB connection can be made from a standard LAN adapter to the RJ45 MGMT
port on the front panel of the Switch. This connection operates at 10/100/1000
Mbps.
Figure 2-1 DXS-3410-32XY Front Panel
This following table lists the front panel components unique to the DXS-3410-32XY:
Port Type
Port Number
Description
RJ45 Ports
(100 Mbps, 1/2.5/5/10 Gbps)
Ports 1 to 24
This switch is equipped with 24 RJ45 Ethernet ports that can
operate at 100 Mbps, 1 Gbps, 2.5 Gbps , 5 Gbps, and 10
Gbps.
SFP+ Ports
(1/10 Gbps)
Ports 25 to 28
This switch is equipped with 4SFP+ Ethernet ports that can
operate at 1 and 10 Gbps.
SFP28 Ports
(10/25 Gbps)
Ports 29 to 32
This switch is equipped with 4SFP28 Ethernet ports that can
operate at 10 and 25 Gbps.

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
3
Figure 2-2 DXS-3410-32SY Front Panel
This following table lists the front panel components unique to the DXS-3410-32SY:
Port Type
Port Number
Description
SFP+ Ports
(1/10 Gbps)
Ports 1 to 28
This switch is equipped with 28 SFP+ Ethernet ports that can
operate at 1 and 10 Gbps.
SFP28 Ports
(10/25 Gbps)
Ports 29 to 32
This switch is equipped with 4SFP28 Ethernet ports that can
operate at 10 and 25 Gbps.
NOTE: The Uplink and Stacking functions cannot operate at the same time on the SFP28 ports in this
switch series.
Front Panel LED Indicators
The LED indicators provide valuable information in a variety of ways like their color, blinking times, and location.
Figure 2-3 DXS-3410-32XY Front Panel (LED Indicators)
Figure 2-4 DXS-3410-32SY Front Panel (LED Indicators)
The front panel LED indicators are described in the following table:
LED
Color
Status
Description
Power
Green
On (Solid)
Power on and system ready
-
Off
Power off
Console
Green
On (Solid)
Console active
-
Off
Console off
RPS
Green
On (Solid)
RPS in use
-
Off
RPS off
USB
Green
On (Solid)
USB disk is connected
On (Blinking)
USB data in transmission
-
Off
No USB device is connected
Fan
Red
On (Solid)
Fan has a runtime error and is brought offline

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
4
LED
Color
Status
Description
-
Off
Fan is operating normally
MGMT (Link/Act)
(Out-Of-Band port)
Green
On (Solid)
Active 1 Gbps connection through the port
On (Blinking)
Data transmitted and received through the port
Amber
On (Solid)
Active 10/100 Mbps connection through the port
On (Blinking)
Data transmitted and received through the port
-
Off
Inactive connection, no link present, or port disabled
Stack ID
Green
This 7-segment LED can display numbers from 1 to 9 and the following
letters: H, h, E, and G. The stacking ID (ranging from 1 to 9) can be
assigned manually by the user or automatically by the system.
H- The Switch functions as the master Switch within the stack.
h- The Switch serves as the backup master Switch within the stack.
E- Displayed if an error is detected during the system's self-test.
G- Displayed when the Safeguard engine enters the exhausted mode.
LED
Color
Status
Description
Link/Act
(10GE RJ45 ports)
Green
On (Solid)
Active 2.5/5/10 Gbps connection through the port
On (Blinking)
Data transmitted and received through the port
Amber
On (Solid)
Active 100/1000 Mbps connection through the port
On (Blinking)
Data transmitted and received through the port
-
Off
Inactive connection, no link present, or port disabled
Link/Act
(10GE SFP+ ports)
Green
On (Solid)
Active 10 Gbps connection through the port
On (Blinking)
Data transmitted and received through the port
Amber
On (Solid)
Active 1 Gbps connection through the port
On (Blinking)
Data transmitted and received through the port
-
Off
Inactive connection, no link present, or port disabled
Link/Act
(25GE SFP28 ports)
Green
On (Solid)
Active 25 Gbps connection through the port
On (Blinking)
Data transmitted and received through the port
Amber
On (Solid)
Active 10 Gbps connection through the port
On (Blinking)
Data transmitted and received through the port
-
Off
Inactive connection, no link present, or port disabled
The LED behavior during the booting or rebooting process is outlined as follows:
1. The Power LED exhibits a steady green light upon powering on until the system is ready.
2. All data port LEDs (including RJ-45 and fiber ports) will emit a simultaneous green or amber solid light once,
then turn off until the system is ready.
3. The 7-segment LED will illuminate with all segments upon powering on until the system is ready, while other
LEDs remain inactive.

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
5
Rear Panel Components
The rear panel features components like an AC power socket, a security lock, an electrical ground point, and more.
Figure 2-5 DXS-3410-32XY Rear Panel
Figure 2-6 DXS-3410-32SY Rear Panel
This following table lists the rear panel components on the Switch:
Port
Description
Security Lock
The security lock, compatible with Kensington standards, enables connection of
the Switch to a secure and immovable device. Insert the lock into the notch and
turn the key to secure it. The lock-and-cable set should be acquired separately.
Redundant Power Supply
The RPS port can be utilized to connect an optional external load-sharing RPS to
the Switch. In the event of internal power failure, the external RPS will promptly
and automatically provide power to the Switch.
Switch GND
Utilize an electrical grounding wire to connect one end to the Switch GND and the
other end to an electrical grounding point, typically located on the mounting rack of
the Switch itself.
AC Power Connector
The AC power cord (included in the package) can be inserted into this receptacle
to provide the Switch with 100-240 VAC power at 50-60 Hz.
Power Cord Retainer Hole
The power cord retainer hole is designed for inserting the power cord retainer,
which secures the AC power cord in place.

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
6
Side Panel Components
The side panels feature components like rack-mounting screw holes, heat dissipating fans and vents.
Figure 2-7 DXS-3410-32XY/32SY Side Panels
The fans are capable of automatically adjusting their speed based on the IC sensor's temperature readings. This
feature is highly sensitive, enabling precise control of the internal temperature by accurately regulating the fan speed.
The following table lists at what ambient temperature the speed of the fan(s) will change:
Fan Mode
Fan Status
DXS-3410-32XY
DXS-3410-32SY
Normal mode
Ultra Low
Below 12°C
Below 17°C
Very Low
Above 15°C (Ultra Low to Very Low)
Below 27°C (Low to Very Low)
Above 20°C (Ultra Low to Very Low)
Below 27°C (Low to Very Low)
Low
Above 30°C (Very Low to Low)
Below 35°C (Medium to Low)
Above 30°C (Very Low to Low)
Below 37°C (Medium to Low)
Medium
Above 38°C (Low to Medium)
Below 42°C (High to Medium)
Above 40°C (Low to Medium)
Below 42°C (High to Medium)
High
Above 45°C
Above 45°C
Quiet mode
Ultra Low
Can only be enabled if below 30°C. Returns to Normal mode is above 30°C.
NOTE: When the Quiet Mode is enabled, ports 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, and 24 will be
disabled.

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
7
3. Installation
Installation Guidelines
This section will cover the hardware installation guidelines that the user needs to adhere to for the correct and safe
installation of this Switch in the suitable environment.
Visually inspect the power cord to ensure it is securely connected to both the power connector on the Switch
and the electrical outlet providing power.
Position the Switch in a cool and dry location within the specified operating temperature and humidity ranges.
Place the Switch in a location that is devoid of powerful electromagnetic field generators, such as motors,
vibrations, dust, and direct sunlight exposure.
Installing the Switch without a Rack
This section provides guidance for users installing the Switch in a location outside of a Switch rack. Affix the provided
rubber feet to the underside of the Switch. Please be aware that there are designated areas marked on the bottom of
the Switch indicating where the rubber feet should be attached. These markings are typically located in each corner
on the underside of the device. The rubber feet serve as cushions for the Switch, safeguarding the casing against
scratches and preventing it from causing scratches on other surfaces.
Figure 3-1 Attaching rubber feet to the Switch
Place the Switch on a stable, even surface capable of bearing its weight. Avoid putting heavy objects on the Switch.
The power outlet should be located within 1.82 meters (6 feet) of the Switch. Ensure sufficient heat dissipation and
proper ventilation around the Switch. Allow a minimum of 10 cm (4 inches) of clearance at the front, sides, and rear of
the Switch for ventilation.

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
8
Installing the Switch in a Standard 19" Rack
This section is used to guide the user through installing the Switch into a Switch rack. The Switch can be mounted in a
standard 19"(1U) rack using the rack mounting kit included in the package contents.
Fasten the mounting brackets to the sides of the Switch using the screws provided.
Figure 3-2 Attaching the rack-mounting brackets
Fasten the mounting brackets in any available open space in the rack using the screws provided.
Figure 3-3 Installing the Switch in a Rack
Make sure that there is adequate space around the Switch to allow for proper airflow, ventilation, and cooling.

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
9
Installing Transceivers into the Transceiver Ports
The Switch is outfitted with SFP+ and SFP28 ports designed for linking different networking devices to this Switch,
especially those incompatible with the standard RJ45 wiring connection. Typically, these ports establish connections
between this Switch and optical fiber links, facilitating communication over considerable distances. While RJ45 wiring
connections have a maximum reach of 100 meters, fiber optic connections can extend over several kilometers.
The figure below illustrates the procedure for inserting SFP28 transceivers into the SFP28 ports.
Figure 3-4 Inserting SFP28 transceivers into the SFP28 ports
NOTE: Only use pluggable optical modules and Direct-Attach Cables (DAC) that meet the following
regulatory requirements:
Class 1 Laser Product
UL and/or CSA registered component for North America
FCC 21 CFR Chapter 1, Sub-chapter J in accordance with FDA & CDRH requirements
IEC/EN 60825-1/-2: 2007 2nd edition or later, European Standard

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
10
Connecting AC Power to the Switch
To connect AC power to the Switch, insert one end of the AC power cord into the Switch's AC power socket, and the
other end into the local AC power source outlet. The Switch lacks a power switch/button; it will initiate powering on
automatically.
Once the system is activated, the Power LED will flash green, signifying the boot-up process. In case of a power
failure, as a precautionary measure, disconnect the power cord from the Switch. After power is restored, reconnect the
power cord to the Switch's power socket.
Installing the AC Power Cord Retainer
To prevent accidental removal of the AC power cord, it is recommended to install the AC Power Cord Retainer Set
together with the AC power cord. The AC Power Cord Retainer Set is included in the package contents.
With the rough side facing down, insert the tie wrap into
the hole below the power socket.
Plug the AC power cord into the power socket of the
Switch.
Figure 3-5 Insert Tie Wrap into the Switch
Figure 3-6 Connect the power cord to the Switch

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
11
Slide the retainer through the tie wrap until the end of the
cord.
Circle the tie of the retainer around the power cord and
into the locker of the retainer.
Figure 3-7 Slide the Retainer through the Tie Wrap
Figure 3-8 Circle around the power cord
Fasten the tie of the retainer until the power cord is secured.
Figure 3-9 Secure the power cord

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
12
Installing the Redundant Power Supply (RPS)
An RPS (Redundant Power Supply) is an external unit encased in a durable metal casing. It features sockets for
connecting AC or DC-powered sources at one end and links to a Switch's internal power supply at the other end. The
RPS offers an economical and straightforward remedy to address the risk of an unintended internal power supply
failure within an Ethernet Switch. Such a failure could lead to the shutdown of the Switch itself, the devices connected
to its ports, or even an entire network.
Connecting the DPS-500A RPS to the Switch
The D-Link DPS-500A is the recommended RPS for the Switch. This RPS is specifically engineered to adhere to the
wattage requirements of D-Link's Ethernet Switches, and it can be linked to the RPS port of the Switch using a 14-pin
DC power cable. A standard three-pronged AC power cable is used to connect the RPS to the main power source.
CAUTION: Do not connect the RPS to AC power before the DC power cable is connected. This might
damage the internal power supply.
ATTENTION: Ne branchez pas le RPS sur le courant alternatif avant que le câble d'alimentation en
courant continu ne soit branché. Cela pourrait endommager l'alimentation électrique interne.
To establish a connection between the RPS and the Switch, begin by detaching the AC power cord from the AC
power port of the Switch. Employ a Phillips-head screwdriver to remove the RPS port cover by loosening the two
screws that secure the RPS cover in place.
Figure 3-10 Removing the RPS port cover
Insert one end of the 14-pin DC power cable into the RPS port on the Switch and the other end into the RPS unit.
Connect the RPS unit to the main AC power source.
Figure 3-11 Connecting the DPS-500A

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
13
A green LED on the front panel of the RPS unit will illuminate, indicating a successful connection. Reattach the AC
power cord to the AC power port of the Switch. The RPS LED indicator on the front panel of the Switch will confirm the
presence and operation of the RPS. No software configuration is necessary.
CAUTION: Leave at least 15 cm (6 inches) of space at the rear of the Switch when an RPS is installed
to prevent cable damage.
ATTENTION: Laissez un espace d’au moins 15 cm (6 pouces) à l'arrière du commutateur lorsqu'un RPS
est installé pour éviter d'endommager les câbles.
Always keep the RPS port cover installed when there is no RPS connected to the Switch.
Figure 3-12 Reinstalling the RPS port cover (when no RPS is connected)

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
14
4. Switch Connections
Stacking the Switch
Switches in the series can be physically stacked by utilizing the last four ports on the front panel of the Switch. It is
possible to stack up to nine Switches, which can then be managed through a single connection to any of the LAN
ports using Telnet, the Web UI, and SNMP. This cost-effective Switch presents an economical solution for
administrators aiming to upgrade their networks, leveraging the stacking ports for scaling and stacking purposes. This
ultimately enhances overall reliability, serviceability, and availability.
The Switch supports the following stacking topologies:
Duplex Chain - This topology interconnects Switches in a chain-link format, enabling data transfer in one
direction only. A disruption in the chain will impact data transfer.
Duplex Ring - In this topology, Switches form a ring or circle, allowing data transfer in two directions. It is highly
robust, as even if the ring is broken, data can still be transmitted via the stacking cables between Switches
using an alternative route.

DXS-3410 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
15
In the following diagram, Switches are stacked in the Duplex Chain topology.
Figure 4-1 Duplex Chain Stacking Topology