D-Link DKVM-IP8 User manual

Industrial grade IP KVM switch
User manual

Thank you for purchasing this IP-KVM switch. The IP KVM that
means a KVM switch with remote management function. A set
of keyboard, mouse, and monitor control multiple computers
and can remotely control multiple computer servers. IP KVM
transmits each computer's signal to the IP data packet through
the Internet or private network. At the remote control side, the
IP signal will be compiled again into keyboard, mouse, and
monitor signals. In order to ensure data security, data packets
are usually encrypted. And IP KVM can provide remote
management without distance restrictions.
●USB2.0 port, with USB hub, support any USB2.0 devices.
●System supported: DOS, Win95/ 98/ 98SE/ 2000/ ME/ XP,
WinNT, Netware, Unix, Linux.
●Plug and play, can plug in or unplug the connected computer
without turning off the KVM switch and computer. Hot
plugging is not recommended.
●Excellent picture quality, resolution up to 1920*1440,
bandwidth 350MHz.
●No software neededl: control the host computer that need
operate for network control via buttons, hotkey, OSD menu.
●With buzzer.
●With LED light.
●Support auto-scanning, default 5s.
Packing contents
1* 16 port KVM switch
4* KVM cable
1* user manual
1* DC 12V power adapter
1* CD
1* 8 port KVM switch
4* KVM cable
1* user manual
1* DC12V power adapter
1* CD
8 port IP KVM switch 16 port IP KVM switch
Description
Features

1~8/ 1~16 panel switch button
reset button
input port
Output port
USB Hub
LED flash fast that means data interaction
power port
USB ports and 8 serial ports are vendor-specific
interfaces that users cannot use
LAN port: Ethernet interface
Red LED: 0M Ethernet connected
Green LED: 100M Ethernet connected
Interface instruction

Hotkey command introduction
In addition to the front panel buttons, the KVM switch port can
also be used via a simple keyboard combination. Simply press
the HOME/ Cap / Scroll / Num keys twice within 2s to send a
command to the KVM and you will hear ” Beep ". After confirm
that you can use the hotkey command, this product has multiple
modes to choose. HOME+ HOMEis the default mode, when
you do not want to use this mode, you can choose another
command mode. The following is the way to set different hotkey
mode.
default mode
+ Caps Enter hot-key Caps mode
+ Scroll enter hot-key Scroll mode
+Num Enter hot-key Num mode
Default mode command
Switch to the corresponding port.
Switch to Next
Switch to Pre.
Off/ on the buzzer
Auto-scanning, press any key to
stop auto-scanning
or
or

Home+ home + Num. +enter: set the auto-scanning intervals,
from 5 - 999s
If you would like to use Caps mode, please press Home+
Home+ Caps first
Caps mode Command
Switch to the corresponding port.
Switch to Next
Switch to Pre.
Off/ on the buzzer
Auto-scanning, press any key to
stop auto-scanning
or
or
Caps+ Caps+ I+ Num+ enterset the auto-scanning intervals,
from 5 - 999s
OSD menu opearation
Hot-key also can be achieved under OSD mode, According to
the below way to choose one hot-key port from OSD menu.
Home+ Home+ Enter to active OSD menu.
Note: If you are using OSD, you can click directly when you are
on the main menu.

F1: Revise port name
Main menu
According to User selected, red
letter will be revised.
Cascade indication, 00 represents the first level,
00represents the second level.
the digital of port: 8 shows 8 port KVM
switch, 16 shows 16 port KVM switch.
Port selected.
the port auto-scanning selected.
USB port is connected correctly.
Menu setting

F2:Set the port to be scanned, used with auto-scanning mode
2TAG (press F2to open or close the scan, identify “ T”,
as shown in Figure 2 below)
F3:Set system
F4:Scan port
F6:Set the host to be assigned non-administrator users (which
hosts User 1-7 can operate)
F7:Set user login
Note: F1, F2, F3, F4, F6, F7 need to press on keyboard.
F1:Modify the host name
Note: You can change the name of the host as you like, use the
keyboard up and down key to control, when you need to change
the host name, press the enter on keyboard can be changed

Setting method: Under the current option, press enter to enter
the setting:
01: Buzzer on/ off
02: Autoscan Mode
0: All of ports
1: The option ID only scans the PC port connected to
the USB
2: only scans the port that mark by “T”(as figure 3)
03: Autoscan interval, default 5s
04: After switching, the OSD shows the Banner interval
05: After switching, OSD shows banner position, after entering,
press Alt+ “↑↓←→” key to adjust position
06: Plugin Jump Mode
F3:System setting

0:The device will be automatically switched to the port just
inserted into the USB device when all the ports are free
1:Plug in a USB device (When USB port has a 5V devices
input), it automatically switches to the one you plugged in,
giving priority.
Note: The PLUGING JUMP MODE setting is only useful if JUMP
CHECK is set to 1.
07:JUMP CHECK
0:NONE: Does not detect, Port switching could via panel keys
or hotkey
1:POWER: Detects the USB is correctly plugged in and can
only be switched on the port where the USB device is
plugged in
Note: If set to 1, you can not switch to the port that has no USB
plug, regardless of the hotkey or keypad operation
08:Check the software version information
F7：Enter the user settings

When you press F7 into the user settings, the screen shown in
Figure 4, SECURIY: Y represents that need the password to
enter, N on behalf of don’t need the password to enter, press
the "↓" into the user account, Press “enter” to into, enter the
screen as Figure 5
F1: modify the user name (user name: ADMIN, USER1, USER2,
USER ..... behind 6 X is hidden password, you need to
press F9 to view)
F9: View the current password (the figure above by F9 shows
the first user's default password is 000000)
F4: Change the password
However, when set to Y, the OSD adds F5: LOGOUT
options. Each time you login will be prompted, as shown in
Figure 6: