DAB NOVA User manual

OWNER’S MANUAL
C US

DAB PUMPS reserves the right to make modifications without notice
DECLARATION OF CONFORMITY
(IT) DICHIARAZIONE DI CONFORMITÀ CE
Noi, DAB Pumps S.p.A. - Via M.Polo, 14 – Mestrino (PD) – Italy,
dichiariamo sotto la nostra esclusiva responsabilità che i prodotti ai quali questa di- chiarazione si riferisce sono conformi alle
seguenti direttive:
• 2006/95/CE (Low Voltage Directive)
• 2004/108/CE (Electromagnetic Compatibility Directive)
• 2011/65/EU (Restriction of the use of certain hazardous substances in electrical and electronic equipment)
ed alle seguenti norme:
• EN 60335-1 : 10 (Household and Similar Electrical Appliances – Safety)
• EN 60335-2-41 : 05 (Particular Requirements for Pumps)
(US) DECLARATION OF CONFORMITY CE
We, DAB Pumps S.p.A. - Via M.Polo, 14 – Mestrino (PD) – Italy,
declare under our responsibility that the products to which this declaration refers are in conformity with the following directives:
• 2006/95/CE (Low Voltage Directive)
• 2004/108/CE (Electromagnetic Compatibility Directive)
• 2011/65/EU (Restriction of the use of certain hazardous substances in electrical and electronic equipment)
and with the following standards:
• EN 60335-1 : 10 (Household and Similar Electrical Appliances – Safety)
• EN 60335-2-41 : 05 (Particular Requirements for Pumps)
Mestrino (PD), 01/01/2013
IT - Ultime due cifre dell’anno di apposizione della marcatura: 13
US - Last two figures of the year in which the mark was applied: 13
FRANCESCO SINICO
TECHNICAL DIRECTOR

DAB PUMPS reserves the right to make modifications without notice
1. SAFETY MEASURES
Before starting the pump, read this instruction booklet carefully.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
A 10mA or 30mA Residual Current Device (GFI) ) MUST be fitted to the
mains supply of the pump only.
The power cord must never be used to carry or move the pump.
Always use the pump’s handle.
Before taking any action on the pump, always remove the plug from the power socket.
Never remove the plug by pulling on the power cord.
If the power supply cord has been damaged, it must be replaced by the manufacturer or his
authorized customer support service in order to avoid all risks.

DAB PUMPS reserves the right to make modifications without notice
OVERLOAD PROTECTION:
The pump has a thermal overload safety device. In the event of any overhea- ting of the motor, this device automatically
switches off the pump. The cooling time is roughly 15 to 20 minutes, then the pump automatically comes on again.
If the overload cutout is tripped, it is essential to identify and deal with the cause of the overheating.
See Troubleshooting.
1. SAFETY MEASURES
Multi-purpose submersible pumps with a high degree of reliability and safety designed to circulate water in garden ponds, create
water falls and play water features.
Designed to work in both horizontal and vertical installations
NOVA 4100 models are suitable to pump clean water, without fibres and with particles with maximum diam. 0.393” (10 mm).
• Circulating water in Garden ponds.
• Water falls.
• Fountains.
• Water features.
The temperature of the fuid being pumped must never exceed 95°F (35°C).
The pump must not be used to pump salty water, sewage, inlammable, corro- sive or explosive liquids
(e.g. petrol, fuel, diluents), greases, oils or foodstuffs.
If the power supply cord has been damaged, it must be replaced by the manufacturer or his authorized
customer support service in order to avoid all risks.
Before starting the pump, make sure that:
• the voltage and frequency specified on the pump’s nameplate coincide with those of the available power supply;
these pumps are designed for 115 Volt / 60 Hz or 230Volt / 60Hz operation.
• there are no signs of damage to the pump or its power cord;
• the electric connection is made in a dry place, protected against any risk of flooding;
• Conformity with local and State electric codes is mandatory. The National Electric Code requires that a ground fault
circuit interrupter (GFCI) be used in the branch circuit supplying sump, utility, effluent and all fountain pumps, pool
pumps and other pond equipment. Consult a li- censed electrician or your power company if in doubt.
Note: given the different provisions applicable to the safety of electric systems in different countries, make sure that the pump
system, as concerns its intended use, is in accordance with current local or state legislation.
2. USE
Insert the plug on the power cord in a suitable power socket.
Start the pump. 20 times per hour Max.
3. STARTING THE PUMP

DAB PUMPS reserves the right to make modifications without notice
To ensure the proper operation of the pump, it is important to comply with the following recommendations:
• The pump must never be allowed to run dry.
• Never leave the pump in operation when the delivery pipe is clogged.
• Place the pump in a vertical or horizontal position on a fat surface at the bottom of the pond.
Care should be taken not to seat the intake of the pump directly into mud or pond debris as this may cause the
strainer to initially block.
• The pump must only be used when it is immersed in water. If the water runs out, the pump must be stopped immediately
by removing the plug from the power supply.
• It is absolutely essential to prevent any risk of the pump freezing. In the event of freezing temperatures, remove the
pump from the liquid, empty it and keep it in a place where it cannot freeze.
• Check the pump installation regularly to ensure the base inlet is clear of debris and that water is fowing unrestricted
4. RECOMMENDATIONS
Occosionally it may be necessary to clean the water intake chamber.
Unscrew the four screws from bottom plate (pos 1) from the main body (pos. 2).
Thoroughly fush the inner cavity and impeller with clean water
Repfit the base taking care not to damage the o-ring

DAB PUMPS reserves the right to make modifications without notice
5. TECHNICAL DATA
MODEL POWER INPUT
60 Hz
P1 Max P2 In
A
Max
Submersion
HP W HP W
NOVA 4100 1 x 115~ 0.9 670 0.5 380 7.1 22 ft
NOVA 4100 1 x 230~ 0.9 670 0.5 380 3.2 22 ft
MODEL A B H DNM
GAS
PACKING DIMENSIONS CABLE
LENGHT
WEIGHT
lbs
L B H
NOVA 4100 16‘ 5.512 6.102 12.795 1“ ¼ 7.598 7.598 14.764 16 ft 14.8
NOVA 4100 100‘ 5.512 6.102 12.795 1“ ¼ 7.598 7.598 14.764 100 ft 15.9
Any material or manufacturing defects will be corrected during the guarantee period established by current law in the country
where the product is purchased. It is up to the manufacturer to decide whether to repair or replace any faulty parts.
The manufacturer’s guarantee covers all substantial defects attributable to manu- facturing or material defects, providing the
product has been used correctly and in compliance with the instructions.
The guarantee becomes null and void in the event of the following:
• unauthorized attempts to repair the appliance;
• unauthorized technical changes to the appliance;
• use of non-original spare parts;
• manhandling;
• inappropriate use, e.g. for industrial purposes.
The guarantee does not cover:
• parts liable to rapid wear and tear.
For any action under guarantee, contact an authorized customer support service, presenting your receipt for the purchase of the
product.
DAB PUMPS INC
3226 Benchmark Drive,
Ladson South Carolina 29456 – U.S.A.
Ph. 1-843-797-5002
Fax [phone]
www.dabpumps.us
6. GUARANTEE

DAB PUMPS reserves the right to make modifications without notice
Fault Possible causes Solutions
The pump does not run.
Power cord unplugged. Plug cord securely into the socket and
check if there is voltage on the line.
Impeller jammed.
Disconnect the power cord, disassemble
hydraulic part and check if impeller is free
to run.
Suction filter clogged.
Water level under the suction
minimum.
Stop the pump. Reposition pump to ensure
pump is always fully submerged.
Air bubble in the pump, produced
during the plunge.
Get the air out by plunging again the pump
while in a tilted position and shake it with
the discharge tube open
Suction filter clogged. Disconnect the power cord, clean the
hydraulic part.
Discharge tube clogged or obstructed. Disconnect the power cord:
take off the tube and clean it.
Suction filter clogged.
The thermal overload protection in the
pump has activated.
Clean water intake area. Allow pump to
cool for approximately 30 minutes.
Water Temperature exceeds 95°F. Maximum water temperature must not
exceed 95°F.
The pump ran dry Reposition pump to ensure pump is
always fully submerged.
OVERLOAD PROTECTION:
The pump has a thermal overload safety device. In the event of any overhea- ting of the motor, this device automatically
switches off the pump. The cooling time is roughly 15 to 20 minutes, then the pump automatically comes on again.
If the overload cutout is tripped, it is essential to identify and deal with the cause of the overheating.
See Troubleshooting.
7. TROUBLESHOOTING

Via Marco Polo, 14 - 35035 Mestrino (PD) Italy - Tel. [phone] - Fax [phone]
www.dabpumps.com
NOVA-4100-USA - 02/2016
On-line selection tool
DAB PUMPS LTD.
Unit 4 and 5, Stortford Hall Industrial Park,
Dunmow Road,
Bishops Stortford,
Herts
CM23 5GZ - UK
[email protected]
Tel. [phone]
Fax [phone]
DAB PUMPS B.V.
Albert Einsteinweg, 4
5151 DL Drunen - Nederland
[email protected]
Tel. [phone]
Fax [phone]
DWT SOUTH AFRICA
Podium at Menlyn,
3rd Floor, Unit 3001b, 43 Ingersol Road,
C/O Lois and Atterbury street,
Menlyn, Pretoria, 0181 - South-Africa
[email protected]
Tel. [phone]
Fax [phone]
DAB PUMPEN DEUTSCHLAND GmbH
Tackweg 11
D - 47918 Tönisvorst - Germany
[email protected]
Tel. [phone]
Fax [phone]
DAB PUMPS POLAND Sp. z o.o.
Mokotow Marynarska
ul. Postępu 15C
02-676 Warszawa - Poland
Tel. [phone]
DAB PUMPS B.V.
Brusselstraat 150
B-1702 Groot-Bijgaarden - Belgium
[email protected]
Tel. [phone]
Fax [phone]
DAB PUMPS IBERICA S.L.
Avenida de Castilla nr.1 Local 14
28830 - San Fernando De Henares - Madrid
Spain
[email protected]
Tel. [phone]
Fax: [phone]
DAB UKRAINE Representative Office
Regus Horizon Park
4 M. Hrinchenka St, suit 147
03680 Kiev - Ukraine
Tel. [phone]
DAB PUMPS INC.
3226 Benchmark Drive
Ladson, SC 29456 - USA
[email protected]
Tel. [phone]
Fax [phone]
DAB PUMPS CHINA
No.40 Kaituo Road, Qingdao Economic & Technological
Development Zone
Qingdao City, Shandong Province - China
PC: 266500
[email protected]
Tel. [phone]-6270
Fax [phone]
DAB PRODUCTION HUNGARY KFT.
H-8800
Nagykanizsa, Buda Ernó u.5
Hungary
Tel. [phone]
OOO DAB PUMPS
Novgorodskaya str. 1, block G
office 308, 127247, Moscow - Russia
[email protected]
Tel. [phone]
Fax [phone]
DAB PUMPS DE MÉXICO, S.A. DE C.V.
Av Gral Álvaro Obregón 270, oficina 355
Hipódromo, Cuauhtémoc 06100
México, D.F.
Tel. [phone]