Dabi Atlante EAGLE User manual

USER’S MANUAL

1
THIS PAGE WAS INTENTIONALLY
LEFT BLANK

2
TABLE OF CONTENTS
1.INTRODUCTION................................................................................................................................ 5
2.SYMBOLS ............................................................................................................................................ 6
3.WARNINGS AND PRECAUTIONS.................................................................................................. 7
3.1.WARNINGS AND/OR CAUTION DURING TRANSPORTATION AND STORAGE................... 7
3.2.TRANSPORTATION OR STORAGE ENVIRONMENTAL CONDITIONS................................... 7
3.3.INSTALLED EQUIPMENT CONDITIONS BETWEEN OPERATIONS........................................ 7
3.4.OPERATIONAL ENVIRONMENTAL CONDITIONS.................................................................... 8
3.5.ADDITIONAL PROCEDURES PRIOR TO EQUIPMENT USE...................................................... 8
3.6.WARNINGS AND/OR CAUTION TO BE ADOPTED..................................................................... 8
3.6.1.WARNINGS AND/OR CAUTION DURING EQUIPMENT INSTALLATION..................... 8
3.6.2.WARNING AND/OR CAUTION DURING EQUIPMENT USE............................................ 9
3.6.3.WARNING AND/OR CAUTION AFTER EQUIPMENT USE/OPERATION....................... 9
3.7.CAUTION IN CASE OF ABNORMAL EQUIPMENT FUNCTION.............................................. 10
4.EAGLE PANORAMIC X-RAY SYSTEM OVERVIEW............................................................... 11
4.1.DIGITAL SNAP-ON CONFIGURATION ...................................................................................... 11
4.2.DIGITAL FIXED CONFIGURATION............................................................................................ 12
4.3.ANALOG CONFIGURATION........................................................................................................ 13
4.1.POWER SUPPLY UNIT OPTIONS................................................................................................. 14
4.2.FREE STANDING BASE (OPTIONAL)......................................................................................... 14
4.3.LIST OF ACCESSORIES ................................................................................................................ 15
5.RECOMMENDED COMPUTER SYSTEM SPECIFICATIONS................................................. 17
6.COMPUTER SYSTEM CONFIGURATION.................................................................................. 17
6.1.NETWORK ADAPTER CONFIGURATION.................................................................................. 17
6.2.SOFTWARE INSTALLATION....................................................................................................... 20
7.IMAGING PROGRAMS................................................................................................................... 24
7.1.PANORAMIC PROFILES:.............................................................................................................. 24
7.2.CEPHALOMETRIC PROFILES: .................................................................................................... 26
8.CONTROL PANEL ........................................................................................................................... 27
8.1.INTRODUCTION............................................................................................................................ 27
8.2.CONTROL PANEL KEYS .............................................................................................................. 28
8.3.CONTROL PANEL INDICATING LIGHTS .................................................................................. 29
8.4.REMOTE EXPOSURE SWITCH (OPTIONAL)............................................................................. 29
8.5.TURNING THE EQUIPMENT ON ................................................................................................. 30
8.6.MAIN SCREEN ............................................................................................................................... 31
9.PREPARING FOR THE EXPOSURE............................................................................................. 35
9.1.DIGITAL SNAP-ON SENSOR CONFIGURATION ...................................................................... 35
9.2.DIGITAL FIXED SENSOR CONFIGURATION............................................................................ 40
9.3.BEFORE POSITIONING THE PATIENT....................................................................................... 41
9.4.GETTING THE SOFTWARE READY............................................................................................ 41
10.PANORAMIC EXPOSURES............................................................................................................ 42
10.1.GETTING THE SOFTWARE READY........................................................................................ 43
10.2.POSITIONING THE PATIENT................................................................................................... 43

3
10.3.TAKING APANORAMIC EXPOSURE..................................................................................... 45
11.CEPHALOMETRIC EXPOSURE ................................................................................................... 47
11.1.GETTING THE SOFTWARE READY........................................................................................ 47
11.2.POSITIONING THE PATIENT................................................................................................... 48
11.3.TAKING ACEPHALOMETRIC EXPOSURE............................................................................ 48
12.PROCEDURES FOR REUSE........................................................................................................... 50
12.1.CLEANING.................................................................................................................................. 50
12.2.DISINFECTION........................................................................................................................... 50
13.TROUBLESHOOTING GUIDE....................................................................................................... 51
13.1.UNIT OPERATION PROBLEM.................................................................................................. 51
13.2.PATIENT POSITIONING PROBLEM1....................................................................................... 52
14.DISPOSAL OF THE UNIT............................................................................................................... 58
14.1.ENVIRONMENTAL CONTAMINATION................................................................................. 58
15.EQUIPMENT INSTALLATION, CORRECTIVE MAINTENANCE AND CALIBRATION... 59
15.1.INSTALLATION OF THE EQUIPMENT................................................................................... 59
15.2.CORRECTIVE MAINTENANCE............................................................................................... 59
15.3.PREVENTIVE MAINTENANCE................................................................................................ 59
15.4.CALIBRATION........................................................................................................................... 60
15.5.NETWORK OF AUTHORIZED SERVICE TECHNICIANS ..................................................... 60
16.TECHNICAL SPECIFICATIONS................................................................................................... 60
16.1.REGULATORY INFORMATION .............................................................................................. 60
16.2.GENERAL INFORMATION....................................................................................................... 61
16.3.RADIOLOGICAL INFORMATION ........................................................................................... 61
16.4.X-RAY GENERATOR................................................................................................................. 62
16.5.TESTED EQUIPMENT LAW NORM......................................................................................... 62
16.6.IRRADIATED FIELD SIZE -DIGITAL PANORAMIC EXAM (PAN: ADULT AND CHILD –
TMJ –MAXILLARY SINUS) ..................................................................................................................... 67
16.7.IRRADIATED FIELD SIZE –DIGITAL CEPH EXAM: ............................................................ 67
16.8.TUBE SPECIFICATIONS........................................................................................................... 68
16.9.ELECTROMAGNETIC EMISSIONS ......................................................................................... 68
16.10.ELECTROMAGNETIC IMMUNITY...................................................................................... 69
16.11.CHARACTERISTIC COOLING OF THE X-RAY GENERATOR......................................... 72
16.12.CHARACTERISTIC CURVES OF THE X-RAY TUBE......................................................... 73
17.LABELS OF IDENTIFICATION..................................................................................................... 74
17.1.PACKAGE................................................................................................................................... 74
17.2.PRODUCT ................................................................................................................................... 75
18.EQUIPMENT DIMENSIONS........................................................................................................... 76
19.WARRANTY...................................................................................................................................... 77

4
Attention
For greater safety:
Read and understand all instructions written in this manual before installation or use of
the equipment.
This instruction manual should be read by all operators of the equipment.
This instruction manual was originally written in Portuguese.
Intended Use
Intended for dental radiographic examination and diagnosis of diseases of the teeth,
jaw and oral structures.
CAUTION
US FEDERAL LAW RESTRICTS THIS DEVICE TO SALE BY
OR ON THE ORDER OF A DENTIST OR PHYSICIAN.
Warning Statement
Only personnel authorized by Dabi Atlante are qualified to install and service this
equipment. Any attempt to install or service this equipment by anyone not so authorized
will void the warranty.
It is imperative that this equipment be installed, serviced, and used by personnel
familiar with the precautions required to prevent excessive exposure to both primary and
secondary radiation. This equipment features protective designs for limiting both the
primary and secondary radiation produced by the X-ray beam. However, design features
cannot prevent carelessness, negligence, or lack of knowledge.
Dabi Atlante requires anyone moving or transporting their machine to contact authorized
service network Dabi Atlante.

5
1. INTRODUCTION
The EAGLE Panoramic X-Ray Machine is a complete system for dental imaging
capable of:
Analog Panoramic Profiles
Analog Cephalometric Profiles
Digital Panoramic Profiles
Digital Cephalometric Profiles
The digital machines use a CCD sensor with the traditional scintillator technologies
and auto image processing that allow a speed up the diagnostic and improve the clinic
workflow.
The equipment has three movement axes (two in orthogonal directions and one
rotational) making it possible to execute elaborate imaging profiles.
It features a complex profile movement around the dental arch and radiographic
emission compensation in the spinal region, when necessary reconstructing the dental arch
into a plane image. Each individual profile prioritizes a set of characteristics improving
diagnostic capabilities. For example, the standard panoramic prioritizes image layer width,
constant vertical magnification and homogeneous exposure along the whole image.
Likewise, the low dosage profile prioritizes the reduction of dosage (time and anodic
current).
The profiles can be applied to a variety of patients: adult or child; small, medium or
large. The equipment has predefined exposure parameters depending on patient type.
However, the user can apply whatever is best for the situation.
The user interface is composed of a control panel located close to the patient chin
rest and an exposure switch. A remote exposure switch installed outside the radiation room
is optional. The exposure switch is a dead-man type switch.
Ease of patient positioning is complimented by the patient entry into the machine
from the side.There are three lasers available for positioning: Mid-Saggital plane,
Frankfurt Plane and Image Layer Plane (canine). These features make it possible for the
user to precisely position the patient.
For patient comfort, a demonstration mode is also available making it possible to
inform the patient of the procedure prior to exposure.

6
2. SYMBOLS
Use the icons below to identify the symbols on your equipment.

7
3. WARNINGS AND PRECAUTIONS
3.1. WARNINGS AND/OR CAUTION DURING TRANSPORTATION AND
STORAGE
The equipment must be transported and stored by observing the following:
Care should be taken to prevent falls and impact.
The arrows must be pointing upwards.
Do not stack.
Protect against moisture, rainwater aspersion and wet ground.
This equipment must be unpacked and installed by an authorized technician.
Premature unpacking does not generate safety risks, but leads to the equipment warranty
voidance.
3.2. TRANSPORTATION OR STORAGE ENVIRONMENTAL CONDITIONS
Environmental temperature range for transportation and
storage
0ºC to +55ºC
(+32F to 131F)
3.3. INSTALLED EQUIPMENT CONDITIONS BETWEEN OPERATIONS
Storage ambient temperature range +5C to +45C
(+41F to 113F)
Ambient temperature range recommended by
manufacturer
+15C a +30C
(+59F to 86F)
Storage relative humidity range 30% to 75% (non-
condensing)
Atmospheric pressure range 700 hPa to 1060 hPa
(525 mmHg to 795
mmHg)

8
3.4. OPERATIONAL ENVIRONMENTAL CONDITIONS
Operation ambient temperature range +10C to +35C
(+50F to 95F)
Ambient temperature range recommended +21C a +26C
(69.8F to 78.8F)
Operation relative humidity range 30% to 75%
(non condensing)
Atmospheric pressure range 700 hPa to 1060 hPa
(525 mmHg to 795 mmHg)
3.5. ADDITIONAL PROCEDURES PRIOR TO EQUIPMENT USE
Even prior to its first use, the equipment must be cleaned and disinfected; the same
additional procedures must be followed for reuse, as described in Chapter 11.
3.6. WARNINGS AND/OR CAUTION TO BE ADOPTED
3.6.1. WARNINGS AND/OR CAUTION DURING EQUIPMENT INSTALLATION
The equipment must be installed only by service technicians authorized by the
manufacturer.
Place the equipment on a site where it will not be in contact with moisture or
water.
Install the unit on a site where it will not be damaged by pressure, temperature,
moisture, direct sunlight, dust or salts.
The equipment must not be submitted to inclination, excessive vibration or shock
(including during transportation and handling).
This equipment has not been designed for use in facilities where vapors,
flammable anesthetic mixtures in contact with air, oxygen or nitrous oxide can be
detected.
Check the equipment’s voltage when performing electric installation. Failure to
do so may damage the equipment.
The equipment must be properly grounded. Failure to do so may result in
“Safety Hazard”.
Depending on local regulation the X-Ray emission control may require
installation outside the facility where the equipment is placed, and the operator
may need visual contact with the patient through a window with radiological glass
or similar, since the operator must not lose visual contact with the patient.
Mobile and portable RF communication equipment can affect the EAGLE
Panoramic X-Ray Machine.
This equipment must be solely used by health care professionals as it may cause
radio interference or interrupt the operation of nearby equipment. Mitigatory
measures, such as equipment re-orientation or replacement and the facility’s
screening, may be necessary.

9
3.6.2.WARNING AND/OR CAUTION DURING EQUIPMENT USE
The equipment must be operated only by qualified and trained professionals
(dentists, radiology technicians, hygienists or engineers).
Always observe the display messages, the equipment as a whole and the
patient in order to detect any arising problems early.
In case occasional maintenance is required, use only services provided by
Authorized Service Technicians.
The equipment has been designed to withstand continual and intermittent
operation; therefore, follow the cycles described in these operation
instructions.
Since radiation exposure can cause damage to human cells, it is
recommended that no one should remain in the radiographic examination
room, unless the patient requires restraint. In this case, such individual must
be properly protected against X-Ray emission.
Although this equipment has been designed according to electromagnetic
compatibility standards, it may, under very extreme conditions, interfere with
other equipment. Do not use it with other devices that are sensitive to
interference or with devices that create high electromagnetic disturbances.
ATTENTION
THE MANUFACTURER SHALL NOT BE LIABLE IN CASE:
THE X-RAY MACHINE IS USED FOR PURPOSES OTHER
THAN THOSE FOR WHICH IT HAS BEEN DESIGNED.
DAMAGE CAUSED TO THE EQUIPMENT, THE OPERATOR
AND/OR PATIENT AS A RESULT OF IMPROPER
INSTALLATION AND MAINTENANCE PROCEDURES IN
DISAGREEMENT WITH THE OPERATION INSTRUCTIONS
ACCOMPANYING THE EQUIPMENT.
IMPROPER EQUIPMENT OPERATION.
3.6.3. WARNING AND/OR CAUTION AFTER EQUIPMENT USE/OPERATION
Turn off the x-ray machine's master switch when it is not used for long
periods of time.
Always keep the equipment clean for its next operation.
If the equipment is defective, do not try to fix it yourself, instead call for
authorized technical assistance.
Do not replace any equipment parts. Do not disconnect the cable or other
connections unnecessarily.
The EAGLE Panoramic X-Ray Machine must be off when other equipment
such as an electric scalpel or other similar devices are being used.

10
After using the equipment, clean and disinfect all parts that may have been in
contact with the patient.
3.7. CAUTION IN CASE OF ABNORMAL EQUIPMENT FUNCTION
In case the equipment shows abnormal heating or noise or any other type of
abnormality, check if the problem is related to any of the items listed in chapter 12. If the
problem cannot be solved, turn off the equipment and call for Authorized Technical
Assistance. Use the website http://www.dabi.com.br or call Customer Service at telephone
number: [phone].

11
4. EAGLE PANORAMIC X-RAY SYSTEM OVERVIEW
4.1. DIGITAL SNAP-ON CONFIGURATION
The following image shows the whole system with optional Ceph arm mounted.
ATENTION
THE SECOND SENSOR IS OPTIONAL
Control Panel
Patient Handles
Cephalostat (Optional)
SNAP-ON Senso
r
X-Ray Tube
Head
Rotating Arm
Moving
Mechanism
Base (optional)
SNAP-ON
Sensor Holde
r
Cephalostat Arm
Secondary
Collimator
Ear rods
Nose Support
Head Support
Column

12
4.2. DIGITAL FIXED CONFIGURATION
The following image shows the whole system. No optional ceph arm is available in
this configuration.
Control Panel
Patient Handles
SNAP-ON Senso
r
X-Ray Tube
Head
Rotating Arm
Moving
Mechanism
Base (optional)
Head Support
Column

13
4.3. ANALOG CONFIGURATION
The following image shows the whole system with optional Ceph arm mounted.
Control Panel
Patient Handles
Cephalostat (Optional)
Film Holde
r
X-Ray Tube
Head
Rotating Arm
Moving
Mechanism
Base (optional)
Film
Holder
Cephalostat Arm
Ear rods
Nose Support
Head Support
Column

14
4.1. POWER SUPPLY UNIT OPTIONS
The following image shows the Power Supply Unit options that can be used in all
configurations.
Standard* Slim
*Order on request
4.2. FREE STANDING BASE (OPTIONAL)
The following image shows the optional Free Standing Base.
The equipment will be fixed to the base and wall by an authorized technician during
installation.

15
4.3. LIST OF ACCESSORIES
1 Bite Guide
2 Silicon chin rest cover
3 Chin rest for patient with teeth
4 TMJ and Sinus nose support
5 Chin rest for patient without teeth

16
1 Nose Support
2 Carpus Support
ATTENTION
ALL PARTS, ACCESSORIES AND OPTIONS DESCRIBED IN THIS
OWNER'S MANUAL ARE FOR EXCLUSIVE USE.
USE OF ANY PARTS, ACCESSORIES OR MATERIAL NOT
SPECIFIED OR PROVIDED IN THIS OWNER'S MANUAL IS USER'S
FULL RESPONSIBILITY.

17
5. RECOMMENDED COMPUTER SYSTEM
SPECIFICATIONS
It is imperative that this computer system be dedicated for the EAGLE Panoramic
X-Ray Machine.
Table 1 – Recommended Computer Specifications
Operating System Windows 7 Professional – 64-bit
Windows 8 Professional
Windows 8.1 Professional
Windows 10 Professional
CPU Intel ® Core ™ I5 3.0 GHz or higher
HDD 1 TB or higher
RAM 8 GB
PCI PCI Express (PCIe) slot
NIC Gigabit Ethernet dedicated
Monitor 21.5” - Resolution 1920x1080 or higher
ATTENTION
AN EXCLUSIVE NETWORK ADAPTER IS SHIPPED WITH
THE EQUIPMENT.
THE HARDWARE MUST BE INSTALLED BY AN
AUTHORIZED TECHNICIAN, OTHERWISE MAY RESULT
IN A VOID OF WARRANTY.
6. COMPUTER SYSTEM CONFIGURATION
6.1. NETWORK ADAPTER CONFIGURATION
To verify installation of the network card, follow the procedure:
1 – Verify the Windows system automatically installed the driver for the capture card.
Control Panel All items Control Panel System Device Manager Network
Adapters

18
2 - Make sure the network adapter is installed. If not, install the network card drive using
the CD shipped with the equipment.
3 - After installation restart the computer.
To configure the network card, follow the procedure:
1 - Go to Control Panel Network Internet and Network Connections
2 - Click the right mouse button on the connection DESKTOP Intel Gigabit CT, and visit
the properties.
3 - Go to Settings Advanced tab and search for item “Receive Buffer”
4 - Initially, this setting is disabled. Change the value to 2048 and then click OK.
5 - Go to Settings Advanced tab and search for item “Transmit Buffer”
6 - Initially, this setting is disabled. Change the value to 2048 and then click OK.
7 - Go to Settings Advanced tab and search for item “Jumbo Frames”

19
8 - Initially, this setting is disabled. Change the value to 9014 bytes and then click
OK.
9 - Go to Settings Power Management tab and uncheck all items.
10 – Select Internet Protocol TCP/IP Version Proprieties
11 – Define the IP address 192.168.5.10 and Subnet Mask 255.255.255.0