Dacor Distinctive DECT304 Technical manual

All specications subject to change without notice. Phone: [phone]www.dacor.com
PLANNING
GUIDE
DECT304, DECT365
Distinctive™ 30” and 36” Wide,
Electric Cooktops
Document # PG03-003 Revised 02/13/12 Page 1/2
PRODUCT DIMENSIONS - DECT365
21” (53.3 cm)
36” (91.4 cm)
34” (86.3 cm)
2”
(5.18 cm)
19-3/16” (48.8 cm)
19 3/16” (48.8 cm)
21” (53.3 cm)
30” (76.2 cm)
28 5/8” (72.7 cm)
2”
(5.18 cm)
PRODUCT DIMENSIONS - DECT304
Product tolerances: ±1/16” (±1.6 mm) unless otherwise noted
NOTES:
1. The cooktop is supplied with a flexible, 48 inch long
power conduit consisting of two (2) insulated hot lead
conductors (L1 and L2) and one (1) insulated ground
conductor. There is no neutral connection. All leads are
copper. The conduit is connected to the right rear corner
of the cooktop. Do not cut or lengthen the conduit.
2. These cooktops are not approved for recessed
installation.
Model No. Electrical Circuit Required Total Connected
Load*
Minimum Supply Wire Size
Line and Ground Connections
DECT304 240 Vac, 60 Hz, 30 Amps. 6.7 kW (28 Amps.) No. 10 AWG
DECT365 240 Vac, 60 Hz, 40 Amps. 9.4 kW (39 Amps.) No. 8 AWG
* For reference only, See the product data label on bottom of unit for exact specifications.
ELECTRICAL SUPPLY REQUIREMENTS
WARNING
• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
• This appliance must be installed in accordance with the
accompanying installation instructions.
IMPORTANT: DECT series cooktops are not approved for installation with a raised vent.

All specications subject to change without notice. Phone: [phone]www.dacor.com
PLANNING
GUIDE
DECT304, DECT365
Distinctive 30” and 36” Wide,
Electric Cooktops
Document # PG03-003 Revised 02/13/12 Page 2/2
All tolerances: +1/16” (+1.6 mm), -0 unless otherwise stated
NOTES:
1. Chamfer all exposed edges of decorative laminate to
prevent damage from chipping.
2. Radius corners of cutout and file to insure smooth edges
and prevent corner cracking. Recommend 1/4” or 3/8”
diameter drill In each corner.
3. Rough edges, inside corners which have not been
rounded and forced fits can contribute to cracking of the
countertop laminate.
4. This cooktop has been designed with wide tolerances of
cut-out to cover possible replacement with other brands.
Dacor recommends that you use the minimum cutout
dimensions in the case of new Installation.
1-1/4" (3.2 cm) Canadian
2-1/4" (5.7 cm) US
A - Width of cut
B - Depth of cut Hole in cabinet
1” (2.5 cm) from edge
of cutout to front
of countertop
See notes
floor for conduit
routing:
3 1/2" (9 cm)
deep x 2 1/2" (6.5 cm) wide
1 1/2" (3.8 cm)
min. clearance
IMPORTANT: Under the cooktop it is necessary to install a
partition, spaced from the bottom of the appliance as shown.
CONDUIT OPENING
Model (A) (B) (C) (D) (E) (F) (G) (H)
DECT304
28-11/16” (72.9 cm)
to
28 15/16” (73.5 cm)
19-1/4” (49.0 cm)
to
19-9/16” (49.7 cm)
30”
(76.2 cm)
min.
18” (45.7 cm)
min height from
countertop to
nearest cabinet
on either side
of unit
30” (76.2 cm)
min.* clearance
from countertop
to unprotected
overhead
surface
2” (5 cm) min.
clearance from
cutout to side
wall on the left
and right of the
unit
13” (33 cm)
depth of
unprotected
overhead
12” (31 cm) min.
from bottom of
countertop and
adjacent cabinet
(right side)
DECT365
34-1/16” (86,5 cm)
to
34-5/16” (87.2 cm)
19-1/4” (49.0 cm)
to
19-9/16” (49.7 cm)
36”
(91.4 cm)
min.
* 24” (61 cm) min. clearance if bottom of wood or metal cabinets is protected by not less than 1/4“ (0.6 cm) flame retardant millboard covered with no less
than No. 28 MSG sheet steel 0.015” (0.04 cm) stainless steel, or 0.024” (0.06 cm) aluminum or 0.020” (0.05cm) copper. 30” (76.2 cm) min. clearance
between top of cooking platform and bottom of unprotected wood or metal cabinet.
COUNTERTOP CUTOUT
Wall covering cabinets,
and countertop must
withstand heat up to
200°F (93°C) Install junction
box so that it can
be reached
through the front
of the cabinet
H
CABINET DIMENSIONS AND REQUIREMENTS
5. Always consult the countertop manufacturer for specific
instructions.
6. Ensure the countertop is square and level and ensure no
structural members interfere with space requirements.
7. The junction box, must be located where it will allow
considerable slack in the conduit for serviceability.
8. For solid surface material installations such as Surel™
and Corian®, consult with solid surface manufacturer to
determine if heat reflective tape is required.