Dacor EG366 Technical manual

All specications subject to change without notice. Phone: [phone]www.dacor.com
PLANNING
GUIDE
EG366, EG486
Renaissance®36” and 48” Wide
Slide-in Gas Rangetops
Document # PG04-001 Revised 10/20/14 Page 1/4
A
ELECTRIC CIRCUIT REQUIREMENTS
Circuit Required Total Connected Load
120 Vac 60Hz, 15 Amp. (3 wire) 0.25 Amp @ 120 Vac, 60 Hz
GAS SUPPLY PRESSURE REQUIREMENTS*
Gas Type Manifold Pressure Minimum Gas Supply
Pressure
Natural Gas 5” Water Column 6” Water Column
Propane (LP) 10” Water Column 11” Water Column
* Maximum gas supply pressure for all models is 1/2 psi
IMPORTANT: Installation of a non-combustible material* (up to the hood) or
a backsplash is always recommended, and mandatory if the distance to the
back wall from the rangetop is less than 2 1/2” (Figure 2). When installing a
backguard, use only Dacor model number AEB3609 (EG366) or AEB4809
(EG486).
CABINET/COUNTERTOP SIDE VIEW WITHOUT BACKGUARD
CABINET/COUNTERTOP SIDE VIEW WITH BACKGUARD
PRODUCT DIMENSIONS - SIDE VIEW
PRODUCT DIMENSIONS - ISO VIEW
A - Width
EG366 35 7/8” (91.1 cm)
EG486 47 7/8” (121.6 cm)
Product tolerances: ±1/16” (±1.6 mm) unless otherwise noted
WARNING
• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
• This appliance must be installed in accordance with the
accompanying installation instructions.
4” (10.2 cm) 5/8”
(1.6 cm)
7 3/4”
(19.7 cm)
Trim:
7/16”
(1.1 cm)
thick
26” (66.0 cm)
1 1/2” (3.8 cm) cooking surface
height (grate level) above
countertop
3/4” gas inlet, connects to regulator from
bottom or rear of unit, end is recessed
2” (5.1 cm) from chassis bottom
27” (68.6 cm)
28” (71.1 cm)
Power cord
32” long
Combustible
rear wall
Backguard mandatory if
gap from back of rangetop
to combustible wall is less
than 2 1/2”
Combustible
rear wall
2 1/2” (6.4 cm) min. to
combustible rear wall

All specications subject to change without notice. Phone: [phone]www.dacor.com
PLANNING
GUIDE
EG366, EG486
Renaissance 36” and 48” Wide
Slide-in Gas Rangetops
Document # PG04-001 Revised 10/20/14 Page 2/4
See note 2
2See Cabinet/Countertop Dimensions - Top View
3This specification not applicable for cabinets more
than a horizontal distance of 10” (25.4 cm) from the
edge of the rangetop.
1Vertical to combustible surface from rangetop grate level;
if installing an overhead vent hood, also check the hood
specifications for minimum required clearances.
C
13” (33.0 cm)
max.3
Top of
finished
counter
Grate level
Grate level
18” (45.7 cm)
min.1, 3
30” (76.2 cm)
min.1Cutout for
utility access
Hood
Recommended
gas and electrical
service location,
consult local code
B
10” (25.4 cm) to
combustible side
wall min. both sides 1/2” (1.3 cm)
overhang,
both sides
1 1/2” (3.8 cm)
typical countertop
thickness
7 3/4”
(19.7 cm)
36” (91.4 cm)
typical
Mounting platform
1” (2.5 cm) min.
thickness
Model No. B C
EG366 36” (91.4 cm) 36” (91.4 cm)*
42” (106.7 cm)**
EG486 48” (121.9 cm) 48” (121.9 cm)*
54” (137.2 cm)**
* Minimum ** Recommended
Cabinet tolerances: +1/16” (+1.6 mm), -0 unless otherwise noted.
CABINET/COUNTERTOP DIMENSIONS - FRONT VIEW
CABINET/COUNTERTOP DIMENSIONS -
ISO VIEW
continued on following pages...

All specications subject to change without notice. Phone: [phone]www.dacor.com
PLANNING
GUIDE
EG366, EG486
Renaissance 36” and 48” Wide
Slide-in Gas Rangetops
Document # PG04-001 Revised 10/20/14 Page 3/4
CABINET/COUNTERTOP CUTOUT DIMENSIONS WITHOUT DOWNDRAFT VENT - TOP VIEW
Model No. B - Cutout Width D - Hole Offset
EG366 36” (91.4 cm) 16 5/8” (42.2 cm)
EG486 48” (121.9 cm) 20 13/16” (52.9 cm)
Cutout tolerances: +1/16” (+1.6 mm), -0 unless otherwise stated
Non-combustible
rear wall, rear of
mounting platform
10” (25.4 cm) min.
to combustible wall
above countertop,
both sides
Cabinet face
below countertop
overhang
Increase countertop and overhang
additional 2 1/2” (6.4 cm) min. for
combustible rear wall above
countertop
3/8” (1.3 cm)
countertop overhang
Hole 1/2” dia. (1.3 cm),
2 places, through platform
for hold down bolts
Gas/electrical utility cut-out in right rear corner of
mounting platform 8” W X 6” D (20.3 cm X 15.2 cm),
if gas and electrical are routed through bottom
1/2” (1.3 cm)
countertop
overhang
1” (2.5 cm) thick mounting platform min.
Countertop
Countertop
1/2” (1.3 cm)
countertop
overhang
2” (5.1 cm)
1” (2.5 cm)
11 7/16”
(29.1 cm)
24 5/8”
(62.5 cm)
C
L
D D
B
C
LC L
C
L
Gas connection and power cord may be
routed through bottom or back of chassis
Gas and electrical connections at
right rear section of chassis

All specications subject to change without notice. Phone: [phone]www.dacor.com
PLANNING
GUIDE
EG366, EG486
Renaissance 36” and 48” Wide
Slide-in Gas Rangetops
Document # PG04-001 Revised 10/20/14 Page 4/4
CABINET/COUNTERTOP CUTOUT DIMENSIONS WITH DOWNDRAFT VENT - TOP VIEW
CABINET/COUNTERTOP CUTOUT DIMENSIONS
WITH DOWNDRAFT VENT - SIDE VIEW
Model
No.
B - Cutout
Width
D - Hole
Offset
E - Downdraft
Vent Cutout
EG366 36”
(91.4 cm)
16 5/8”
(42.2 cm)
33 1/2”
(85.1 cm)
EG486 48”
(121.9 cm)
20 13/16”
(52.9 cm)
43 1/2”
(110.5 cm)
Model
No.
Approved Downdraft
Vent Models
EG366 ERV36, ERV3615, PRV36
EG486 ERV48, PRV48
Cutout tolerances: +1/16” (+1.6 mm), -0 unless otherwise stated
Non combustible rear
wall recommended 10” (2.5 cm) min. to
combustible wall
above countertop,
both sides
Cabinet face
below countertop
overhang
3/8” (1.0 cm) min.
countertop overhang
2 5/8”
(6.7 cm)
Hole 1/2” dia. (1.3 cm),
2 places, through platform
for hold down bolts
1/2” (1.3 cm)
countertop
overhang
1” (2.5 cm) thick mounting platform min.
Open to below to allow for downdraft
vent, gas and electrical connections
Countertop
Countertop
1/2” (1.3 cm)
countertop
overhang
2” (5.1 cm)
1” (2.5 cm)
11 7/16”
(29.1 cm)
15”
(38.1 cm)
24 5/8”
(62.5 cm)
C
L
DD
E
B
C
LC L
C
L
Stiffener
Cabinet face
Control panel
Countertop
Dacor approved
downdraft vent
IMPORTANT: See downdraft
vent installation instructions
for duct system
layout/planning
EG366 or EG486 rangetop
3/8” min. (1.0 cm)
space behind
downdraft vent
chassis to clear
stiffener
3/8” min. (1.0 cm)
flat countertop overhang
required behind cutout
Minimum
countertop
height:
30 1/4"
(76.8 cm)
IMPORTANT: Use only the downdraft vents specified.