Dacor Millenia DR30D Technical manual

PLANNING
GUIDE
www.Dacor.com Phone: [phone]
Specications subject to change without notice.
Install all appliances according to accompanying installation instructions. 5.14
Ranges equipped for installation in Canada:
Ranges equipped for use in Canada come pre-wired with a 4-wire,■
66 inch (168 cm) long, appliance cord and NEMA 14-50P plug.
Do not modify the factory wiring. The plug is designed to plug directly■
into a NEMA 14-50R electrical receptacle installed by a licensed
electrician.
All other models:
The conduit or appliance cord installed needs to be long enough to allow
the range to be pulled out from the wall for service, while remaining
connected. See next page for further details.
The wiring to the range must:
Include a strain relief.◊
Be terminated by tinned leads, closed loop terminals or open ended◊
spade lugs with upturned ends.
Where local code permits, a 3 or 4 wire
appliance cord may be used. It must:
Be UL listed type SRD or SRDT.◊
Be equipped with a NEMA 14-50P 4-wire◊
plug or, where local code permits, a
NEMA 10-50P 3-wire plug.
Distinctive Range
DR30D
Optional Backguard and Island Trim Part Numbers
Description Part Number
Island trim kit (no backguard) ADTK30
6 inch trim kit ADB3006
9 inch trim kit ADB3009
Electrical Specifications
Circuit Required Total Connected Load
240 Vac, 60 Hz., 30 Amp.* 5.7 kW (23.8 Amp.)
The ratings above are for reference only - refer to the range's product data
label for exact specifications.
NOTE: This range is NOT designed for self-rimming installation or
installation with a raised vent.
1 1/8” (2.9 cm)
Rear of front panel/oven door
Front of knobs
Front of open door
Front panel
3” (7.6 cm)
Backguard*
6” (15.2 cm)
Backguard**
** Optional
Standard
*
37 7/8”
(96.2 cm)
to
35 3/4”
(90.8 cm)
Width at front panel:
29 7/8” (75.9 cm)
Finished side panel
9” (22.9 cm)
Backguard**
1 1/8” (2.9 mm) to cooking
surface (top of grates) from
top of trim
26 1/2” (67.3 cm)
28 1/2” (72.4 cm)
24 3/8” (61.9 cm)
46 3/8” (117.8 cm)
All tolerances: ±1/16” (±1.6 mm) unless otherwise stated.
WARNING
Observe all governing codes and ordinances during•
planning and installation. Contact your local building
department for further information.
This appliance must be installed in accordance with•
the accompanying installation instructions.
Document # PG05 - 006 Revised 1/26/10 Page 1/2
* Two 120 Vac hot (L1 and L2), one neutral, one ground
The regulator inlet accommodates a 3/4” gas line. The range ships with a
1/2” to 3/4” adapter connected to the regulator.
Gas - Electrical Access Dimensions
ABCD
4 3/4”
(12.1 cm)
22 1/8”
(56.2 cm)
8 3/4”
(22.2 cm)
13 3/4”
(34.9 cm)
B
Gas
inlet
A
C
7/8” (2.2 cm) dia. electrical
connection hole in bottom*
D
Range electrical access,
cover removed
GAS AND ELECTRICAL DIMENSIONS
PRODUCT DIMENSIONS
Gas Supply Pressure Requirements*
Gas Type Manifold Pressure Minimum Gas Supply
Pressure
Natural gas 5” water column 6” water column
LP 10” water column 11” water column
* Maximum input gas supply pressure for all models is 1/2 p.s.i.
7/8" to 1 1/8" dia. access hole

PLANNING
GUIDE
www.Dacor.com Phone: [phone]
Specications subject to change without notice.
Install all appliances according to accompanying installation instructions. 5.15
Distinctive Range
DR30D
Note 2
E
F
2Cabinet/countertop depth is at discretion of customer but
cabinet face MUST NOT protrude further than rear of front
panel, see product dimensions.
3Consult local code for exact location requirements.
1Vertical to combustible surface from range grate level; if
installing an overhead vent hood, also check the hood
specifications for minimum required clearances.
Non-combustible
surface along
back wall
recommended
10” (25.4 cm) Min.
to combustible side
walls above the range
(both sides)
30” (76.2 cm)
Min.1
37 7/8
(96.2 cm)
Max.
13” (33.0 cm)
Max.4
18” (45.7 cm)
Min.1, 4
Suggested
location of
utilities 3
4Not applicable for cabinets more than a horizontal
distance of 10” (25.4 cm) from the edge of the range.
Cutout Dimensions
E F
36” (91.4 cm)*
30” (76.2 cm)** 30 1/16” (916mm)
* Recommended
** Minimum
Gas and Electrical Service
The shaded area shown below denotes the location of the gas inlet■
and the electrical junction box/receptacle. This is the recommended
location. For replacement purposes, the location of the existing
utilities may be utilized provided they do not interfere with the sides
or rear of the range. Check local building codes for permissible gas
valve locations.
An external manual shut-off valve must be installed between the gas■
inlet and the range for the purpose of turning on or shutting off gas to
the appliance.
The installation must allow for the following:
Access to the gas shut-off valve when the unit is installed.■
Access to the remote circuit breaker panel/fuse box when the range■
is in place.
The gas supply piping, gas shut-off valve and the electrical junction■
box or receptacle must be located so they do not interfere with the
range when it is installed.
The junction box and gas shut off valve must be located so that■
the range can be pulled out for service while the appliance remains
connected.
Cabinet Layout
Carefully check the location where the range is to be installed. For■
best performance, the range should be placed away from drafts that
may be caused by doors, windows and heating and air conditioning
outlets.
To reduce the risk of personal injury and to reduce accumulated■
smoke in the room, Dacor strongly recommends installing a range
hood. A range hood should project horizontally a minimum of five (5)
inches beyond the face of the cabinets.
All maximum and minimum dimensions and clearances shown in the■
diagram below must be maintained for safe operation.
The range may be installed flush to the rear wall. A non-combustible■
rear wall is not mandatory, but Dacor highly recommends installing
a non-combustible material from the countertop level up to the vent
hood or installation of a backguard.
Any openings in the wall behind the appliance or in the floor■
underneath it must be sealed.
REQUIRED CABINET DIMENSIONS
Cabinet tolerances: -1/16”, (+1.6mm) -0
Document # PG05 - 006 Revised 1/26/10 Page 2/2