Dacor Epicure ER30GSCH/NG User manual

Epicure ®30-Inch Gas
For use with models ER30G and ER3OGI
Installation
Range
Instructions
THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST EDITION
OF ANSI Z21.1 STANDARD FOR HOUSEHOLD GAS COOKING APPLIANCES.
PartNo. 106174 Rev. H
All manuals and user guides at all-guides.com
all-guides.com

Important Safety Instructions ..................................................... 1
Important Information About Safety Instructions ......................... 2
General Safety Precautions ........................................................ 2
Installation Specifications ........................................................... 3
Product Dimensions .................................................................... 3
Electrical Power Supply Requirements ...................................... 4
Gas Supply Requirements .......................................................... 4
Cabinet Layout ............................................................................ 5
Gas and Electrical Locations ...................................................... 6
Installation Instructions ............................................................... 6
Verifying the Package Contents ................................................. 6
Parts List ..................................................................................... 6
Backguard Kit Installation ........................................................... 7
Self-Rimming Trim Installation .................................................... 7
Adjust the Range Height ............................................................. 8
Install the Anti-Tip Bracket .......................................................... 9
Door Removal ............................................................................. 9
Gas Connection ........................................................................ 10
Moving the Range to Final Location ......................................... 11
Re-Installing the Door ............................................................... 11
Cooktop Assembly .................................................................... 12
Verifying Proper Operation ....................................................... 13
Installation Checklist ................................................................. 13
Wiring Diagram ........................................................................... 14
Notes ............................................................................................ 15
IMPORTANT:
• Installer: In the interest of safety and to minimize problems, read these installation instructions completely and
carefully before you begin the installation process. Leave these installation instructions with the customer.
• Customer: Keep these installation instructions for future reference and the local building inspector's use.
If the unit requires service or you have questions or problems with
installation of this product, contact your Dacor ®dealer or the Dacor
Customer Service Team.
Dacor Customer Service
[phone] (U.S.A. and Canada)
Monday -- Friday 6:00 A.M.to 5:00 P.M.Pacific Time
Web site: www.Dacor.com
Be sure to have the model and serial number available when you
call. The model and serial number are on the model/serial number
label. It can be seen by opening the oven door and looking through
the slot near the left hinge between the door and bottom of the oven
chamber.
Model Identification
View model/serial
number label
through slot near
left hinge
Side Panel Standard Operating
Model Number Gas Type
Type* Backguard* Altitude**
Below
ER30GSCH/NG Full NG 6 Inch 4000 Ft.
Below
ER30GSCH/LP Full LP 6 Inch 4000 Ft.
4000 Ft.
ER30GSCH/NG/H Full NG 6 Inch and over
4000 Ft.
ER30GSCH/LP/H Full LP 6 Inch and over
Below
ER30GISCH/NG Partial NG 1 3/4 Inch 4000 Ft.
Below
ER30GISCH/LP Partial LP 1 3/4 Inch 4000 Ft.
4000 Ft.
ER30GISCH/NG/H Partial NG 1 3/4 Inch and over
4000 Ft.
ER30GISCH/LP/H Partial LP 1 3/4" Inch and over
See page 3 for more information. ** 4000 Ft. = 1219 M
Optional Accessories
For Use With
Part Number Description Model(s)
Low Profile
AER30GLBG (1 314" Inch) ER30G***,
ER30GI
Backguard Kit
ER30G,
AERB30G03 3" Backguard Kit ER30GI ....
AERB30G06 6" Backguard Kit ER30G,
ER30GI ....
ER30G,
AERB30G09 9" Backguard Kit ER30GI ....
*** Not compatible with ER30G units with a serial
number starting with the letters "KA."
.... Use only the factory installed (1 3/4")
backguard with self-rimming installations.
All specifications subject to change without notice. Dacor assumes no liability for changes to specifications.
© 2008 Dacor, all rights reserved.
All manuals and user guides at all-guides.com

Important Information About Safety
Instructions
The Important Safety Instructions and warnings in this
Manual are not meant to cover all possible problems and
conditions that can occur. Use common sense and caution
when installing, maintaining or operating this appliance.
Always contact the Dacor Customer Service Team about
problems or conditions you do not understand.
Safety Symbols and Labels
READ AND SAVE THESE
INSTRUCTIONS
_acar 1
All manuals and user guides at all-guides.com

General Safety Precautions
To reduce the risk of fire, explosion, electric shock, serJous Jnjury or death when JnstallJng or usJng thJs
applJance, follow basJc safety precautJons, JncludJng the followJng:
•Read the accompanying use and care manual completely before operating this appliance.
• Keep packaging materials away from children. Plastic sheets and bags can cause suffocation
• If you receive a damaged product, immediately contact your dealer or builder. Do not install or use a damaged
appliance
• This range must be properly installed by a qualified installer according to these installation instructions prior to use.
The installer should show the customer the location of the gas shut off valve and the fuse or junction box so that
they know where and how to turn off the gas supply and electric power to the range.
• Do not operate the range without the backguard in place. A fire may result.
• Do not install, repair or replace any part of the range unless specifically recommended in the literature
accompanying it. A qualified service technician should perform all other service.
• Do not connect this range to the gas supply without the supplied gas pressure regulator installed.
• Before performing any type of service or installation, make sure that the gas supply to the range is turned off and
the power cord is disconnected
• NEVER block or cover any slots, holes or passages anywhere inside the oven or on the outside of the range or
cover an oven rack with materials such as aluminum foil. Doing so blocks airflow through the oven and cooktop and
may cause carbon monoxide poisoning or fire.
• Do not cover the IR broil burner in the top of the oven with cookie sheets, aluminum foil, pots, pans, etc. Covering it
could cause it to overheat resulting in a risk of fire and damage to the oven.
• Only use the range for cooking tasks expected of a home appliance as outlined in the literature accompanying it.
This range is not intended for commercial use. This range is certified for indoor installation only.
• DO NOT TOUCH THE SURFACES OF THE OVEN OR COOKTOP DURING OR IMMEDIATELY AFTER USE.
•Do not climb on any part of the appliance.
• Never leave this appliance unattended when in use.
• Do not leave children alone or unattended in the area around the range. Do not allow children to play with the
controls, pull on the handle, or touch other parts of the range.
• Do not store items of interest to children on top of or above the range. Children could be burned or injured while
climbing on the appliance.
• Do not attempt to use this appliance in the event of a power failure.
• Do not tamper with the controls. Do not adjust or alter any part of the range unless specifically instructed to do so in
these instructions .....
• To prevent the unit from tipping forward and to provide a stable installation, this range must be secured in place with
the anti-tip device as specified in these instructions.
• Clean the cooktop thoroughly before operating it for the first time.
• Keep flammable items, such as paper, cardboard, plastic and cloth away from the burners and other hot surfaces.
Do not place such items in the oven. Do not allow pot holders to touch hot surfaces or gas burners.
• Do not wea r loose or hanging apparel while using the range. Do not allow clothing to come into contact with the
interior of the oven or the cooktop and surrounding areas during and immediately after use.
• To avoid a fire hazard, do not hang flammable or heat sensitive objects over the range.
• If the range is near a window, do not use long curtains as window treatment. The curtains could blow over the
cooktop and create a fire hazard.
• Do not use the oven for storage.
• Make sure that all the cooktop parts are dry before lighting a burner.
• Turn the knobs to the OFF position prior to removing them from the valve stems.
2_acar
All manuals and user guides at all-guides.com

•For your safety, do not use the oven to cook without the convection filter installed. When the filter is not installed,
the spinning fan blades at the back of the oven are exposed.
•The cooktop should never be operated without the knobs and trim rings in place.
Non-stick coatings, when heated, can be harmful to birds. Remove birds to a separate, well-ventilated room during
cooking.
• Always ensure that the light fixture lens cover is in place when using the oven. The lens cover protects the light bulb
from breakage caused by high oven temperatures or mechanical shock.
IMPORTANT - This appliance is equipped with a three-prong grounding plug
for your protection against possible electric shock hazards. Plug it only into a
dedicated, grounded three-prong electrical outlet. It is the responsibility of the
customer to make sure the proper type of outlet is installed. Do not under any
•Use an adapter plug.
• Use an extension cord.
• Use a power cord that is frayed or damaged.
• Connect to an electrical outlet with a ground fault interrupter (GFI).
Product Dimensions All tolerances: +1/16" (+1.6mm), unless otherwise stated
r_
-r,,-I
Ij Product width:
29 7/8" (759mm)
45 9/16" (1157mm) m,
28 9/16" (725mm)
-_ 27 1/16" (687mm) ._
•_ 26 1/8" (664mm)
•_ 24" (610mm) m,
2" (51mm)
_4- ER30GI:
Partial stainless
steel side panel
•4- 3" (76mm)
#
ER30G:
_- Full stainless
steel side panels
i
Front of open door
Front of handle
Front edge of bullnose
Front panel
Rear of front panel
Backguard thickness
NOTE: Neither model is
compatible with a raised vent.
i 6"(152mm)
! 3" (76mm) Backguard*
Backguard*** i
1 3/4" (44ram) Backguard**
| * Standard on model ER30G
| Optional on model ER30GI, NOT
35"
(889mm)
to
37 1/8"
(943mm)
compatible with self-rimming installations
** Standard on model ER30GI
Optional on model ER30G
*** Optional on both models, NOT
compatible with self-rimming installations
ER30G is designed for freestanding install-
ations. ER30GI is designed for installation
in a recessed cabinet or island. ER30G is
NOT equipped for self-rimming installation.
Overall Dimensions
_acar 3
All manuals and user guides at all-guides.com

Electrical Power Supply Requirements
•The range is supplied with a factory installed, 6 foot
long, power cord with a three-prong grounding plug.
It is connected to the chassis at the rear of the range.
It must be connected to a dedicated, grounded three-
prong electrical outlet installed by a licensed electrician.
The electrical installation, including minimum supply
wire size and grounding, must be done in accordance
with National Electric Code ANSI/NFPA 70* and local
codes and ordinances. A copy of this standard may be
obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
The correct voltage, frequency and amperage must be
supplied to the electrical outlet according to the product
data label located on the top of the kick plate under the
door. Remove the door to view the data label (see
page 9). See the Electrical Supply Requirements
table below for reference.
Electrical Circuit Total Connected Load
Required
120Vac 60Hz, 0.5 kW
15 Amp. (4.0 Amp.)
Electrical Supply Requirements
IMPORTANT: The above information is for reference only.
If the information above differs from the information on the
product data label on the appliance, use the information on
the label.
Gas Supply Requirements
• Be certain that the range being installed is correct for
the gas service being provided (natural gas or LP gas).
Check your local building codes for the proper method
of installation. In the absence of local codes, this
appliance should be installed in accordance with the
National Fuel Gas Code ANSI Z223.1/NFPA 54.
An external manual shut-off valve must be installed
between the gas inlet and the range for the purpose of
turning on or shutting off gas to the appliance.
The cooktop comes from the factory with the regulator
installed, Use only the installed regulator, The inlet
accommodates a 3/4" gas line, The range ships with a
1/2" to 3/4" adapter connected to the regulator,
Manifold
Gas Pressure* Min. Gas Supply Max. Input
Type (WC) Pressure (WC) Pressure
Natural 5" 6" 1/2 p.s.i.
LP 10" 11" 1/2 p.s.i.
Gas Supply Requirements
* The gas supply pressure for testing the regulator setting
shall be at least 1 inch water column (249Pa) above the
specified manifold pressure.
IMPORTANT: The information above is for reference only.
If the above data does not agree with the product data
label, use the data on the product data label on top of the
kick plate below the door (remove the door according to the
instructions on page 9 to view it).
The gas connection is located on the back of the unit as
shown below.
|
Gas
-- -, connection
12 1/2" _ I I
(318 mm) , I I
to ± ._ i
(371 mm)l I' II' --
J - I - _+_I_'/2 5/8"
_,__.-_ (67 mm)
Power cord
4_acar
All manuals and user guides at all-guides.com
all-guides.com

Cabinet Layout •Any openings in the wall behind the appliance or in the
floor underneath it must be sealed.
Carefully check the location where the range is to be
installed. For best performance, the range should be
placed away from drafts that may be caused by doors,
windows and heating and air conditioning outlets.
To reduce the risk of personal injury and to reduce
accumulated smoke in the room, Dacor strongly
recommends installing a range hood. A range hood
should project horizontally a minimum of five (5) inches
beyond the face of the cabinets. If installing a range
hood, see the range hood specifications for minimum
clearances in addition to those stated below.
The range may be installed flush to the rear wall. Dacor
recommends installing a non-combustible material on
the rear wall above the range and up to the vent hood.
It is not necessary to install non-combustible materials
behind the range below the countertop height.
Regardless of the type of back wall surface
the range must not be installed
or operated without the
backguard in place. B j
Hood
13" (330mm)
Max.4
18 _'
Min. 1,4
Note 2
Non-combustible
surface along
back wall
recommended
30" (762mm)
Min.
location of
utilities 3
Top of
finished
counter
If cabinet storage space is to be provided directly
above the range, the risk of personal injury may be
reduced by installing a ventilating hood that projects
horizontally a minimum of 5 inches beyond the face of
the cabinets.
10" Min. (254mm)
to any combustibles
above counter both sides
non comubustible
rear wall recommended
I
I
I
I
I
29 114"(743mm)_
countertop opening i
•_ 30" (762mm) _ I
cabinet opening
below countertop i
Cabinet face I
S below countertop
Notch countertop_,
overhang to width of
24 _'
(610mm)
cabinets Countertop overhang
Countertop Height: Min: 34 3/4" (883mm) 2 1/8" (54mm) Max.
Max: 36 7/8" (937mm)
Countertop Thickness: Max: 1 5/8" (41 mm)
Self-Rimming Cutout Dimensions -
Cabinet Depth Exactly 24 Inches s
10" Min. (254mm) rear wall or
to any combustibles countertop edge
above counter both sides
_ 29 1/4" (743mm)_
I countertop opening
I_ 30"(762mm)
iI cabinet opening
iI below countertop
I/ql Cabinet face
I _ I below countertop
i r_ Notch counterto_
overhang to width of
cabinets
Countertop Height: Min: 34 3/4" (883mm)
Max: 36 7/8" (937mm)
Countertop Thickness: Max: 1 5/8" (41mm)
3/4" Min. (19mm)
Countertop overhang
24 1/8"
(613mm)
#
Countertop overhang
2 1/8" (54mm) Max.
Self-Rimming Cutout Dimensions -
Cabinet Depth Greater Than 24 Inches s
"_ 5 Model ER30GI only. Included self-rimming trim kitallows trim to overlap counter on sides and back.
B C
36" (914mm) 37 1/8"
30" minimum recommended
(762mm) 30" (762mm) (943mm)
maximum
minimum
See cutout dimensions above for self-rimming installations.
10" (254mm Min.
to combustible side
walls above the range
(both sides)
A6
1Vertical to combustible surface from range grate level
2Cabinet/countertop depth is at discretion of customer
but cabinet face SHALL NOT protrude further than rear
of front panel. See product dimesions.
Consult local code for exact location requirements.
4 Not applicable for cabinets more than a horizontal
distance of 10" (254mm) from the edge of the range.
Cabinet Cutout Dimensions
All tolerances: +1/16",-0 (+1.6,-0 mm)
unless otherwise stated
dacar 5
All manuals and user guides at all-guides.com

Gas and Electrical Locations
The installation must allow for the following:
Access to the gas shut-off valve when the unit is
installed,
Access to the electrical outlet, when the range is in
place,
The gas supply piping, gas shut-off valve and the
electrical junction box or receptacle must be located
so they do not interfere with the range when it is
installed,
The electrical outlet and gas shut off valve must
be located so that the range can be pulled out for
service while the appliance remains connected,
Both the gas supply piping and shut-off valve and the
electrical outlet must be located so they do not interfere
with the range when it is installed,
Existing utility connections may be used for
replacement purposes, provided they meet local code
and fit within the utility clearance area at the back of
the range (see diagram, right),
12"(305mm)
U
E E
E E
Utility Clearance Behind Range
Verifying the Package Contents
Unpack the range and verify that all required parts have
been provided. If any item is missing or damaged, please
contact your dealer immediately. Do not install a damaged
or incomplete appliance. The customer must report
cosmetic issues immediately to the dealer or builder.
Parts List
• Anti-tip bracket
• 2 grates
• Use and care manual
• Stainless steel cleaner
• 1 dual burner ring
• 1 outer dual burner cap
• 1 inner dual burner cap
• 3 standard burner caps (2 large, 1 small)
• 3 standard burner rings (2 large, 1 small)
• 3 oven racks
The following parts are are included with model ER30GI
only. They are for use with self-rimming installations:
• 3 Self-rimming trim pieces (left, right, rear)
• 11 #8 x 1/4 Torx screws
• 2 Backguard support brackets
See the use and care manual for a list of other optional
accessories and parts.
6_SCD_
All manuals and user guides at all-guides.com

Backguard Kit Installation
See the inside cover for available part numbers and
compatibility.
If installing a backguard other than the standard size,
install it before pushing the range into place. Install the kit
according to the accompanying installation instructions. A
T-20 Torx driver is required.
Self-Rimming Trim Installation
The trim kit is for use with model ER30GI with a self-
rimming cutout only. Install the trim pieces before pushing
the range into place. A T-20 Torx driver is required.
1. Locate the three (3) trim pieces, the two (2) support
brackets and the eleven (11) #8 x 1/4 Torx screws
included with the range.
,Remove and discard the five (5) screws that hold the
backguard in place. Slide the backguard up to remove.
,
,
Remove and discard the screws (4 each) that hold the
existing left and right trim pieces in place.
Slide the existing left and right trim pieces up and off
the range.
,
,
,
,
Slide the provided left and right trim pieces onto the
range. The overhang on each piece goes toward the
back.
Fasten the new trim pieces in place using the provided
#8 x 1/4 Torx screws (2 each side). IMPORTANT: To
ensure proper fit of the range in the cutout, do not use
the screws removed from the range in step 4. Use only
the provided #8 x 1/4" Torx screws.
Overhang
1
Reattach the backguard using three (3) of the #8 x 1/4"
Torx screws.
dacar 7
All manuals and user guides at all-guides.com

Self-Rimming Trim Installation (cont.)
8. Remove and retain the two (2) hex head screws from
the top back corners of the sides of the chassis as
shown.
,
.)
,)
Using the hex screws removed in step 8, attach the
backguard support brackets as shown. The long end of
each bracket goes toward the front of the range. Slip
the back side of the bracket over the back side of the
backguard. Slide bracket
around back
8_SCD_
10. Using two (2) of the provided #8 x 1/4 screws, attach
the bracket to the backguard as shown. Each screw
threads into the backguard through the hole in the back
of the bracket.
/
11. Install the rear trim piece on the back side of the
backguard with the two (2) remaining #8 x 1/4 screws.
Adjust the Range Height
1. For stand alone configurations, raise the range until
the top of the trim around the cooktop is at least
the same height as the countertop. For self-rimming
configurations, raise the range until the bottom of
the trim surrounding the cooktop is even with the
countertop. To adjust the height, turn the foot on the
bottom of each leg as shown below.
,Use a level to make sure that the range does not tilt
front to back or side to side. Readjust the legs as
necessary.
"--..b
I
down
All manuals and user guides at all-guides.com