DAE CC2030 User manual

CC2030-v3.0 installation guide-1.2us_P1
CC2030
02:81:AO:26:11 2019 S 22000432
S/N :
H/W : F/W : H1.0.1
A01
CC2030
3.0 MAC :
Danger
To prevent the risk of electric shock, turn
off all sources of electrical power to the
device during installation or wiring.
Warnings
●Install only by a qualified and trained personnel.
●Follow these instructions accordingly,
otherwise damage may occur to the device.
●Follow electrical rules and regulations in
the selection of wire materials and gauges.
●Avoid having oil, water, metallic powder or
other foreign substances enter the device.
●Avoid using the device in environments
where it will be exposed to steam, corrosive,
or flammable substances; which can cause
short circuits, fires, or explosions.

Cloud Metering Gateway
Installation Guide
Warnings & Precautions
Installation
Description
Dimension
Power
Supply
DC12-24V
A1
F
Ethernet USB
A2
CC2030
02:81:AO:26:11
2019 S 22000432
S/N :
H/W :
F/W : H1.0.1 A01
CC2030
3.0 MAC :
CC2030
02:81:AO:26:11
2019 S 22000432
S/N :
H/W :
F/W : H1.0.1 A01
CC2030
3.0 MAC :
RX
RS485-2
+−+−
RS485-1
2 1
+−
DC12-24V
Power
TX
RX
TX
Reserved
Reserved
A1
F
Ethernet USB
A2
Reserved
Reserved
Ethernet Port
Status LEDs
Power Input
Meter Communication
Status Indicators
RS485 to meters
Front Side Unit : mm
65
351309.5
1
2
35mm
DIN Rail
TS35/7.5 or 15
1.Hook onto the DIN rail
2.Push towards the wall
1. View
3. Wiring2. Mounting
1. CC2030 : The gateway for DAE Cloud
Metering-Water,Electricty
2. DAE Server : meter.iotems.net
Power
Supply
DC12-24V
 
+−
DC12-24V
Cord end terminal
Recommended
Input Power
1.Use the wire size and type as directed by electrical
regulations
2.Make sure that the wire and terminal are making
good contact and tightly screwed.
3.Terminal may only accept wire sizes up to 12 AWG
4.Make sure that the polarity is correct.
Cord end terminal
recommended
Communication Cable
1.Shielded twisted pair UL2464 cable,
24 AWG recommended.
2.Wire ends should be terminated with either
a cord end terminal or blade terminal.
3.Make certain that the wire is screwed securely
to the terminal.
4.Check that the positive (+) and negative
(–) terminals are properly connected.
Wiring Detail：
Red (+) White (–)
V3.0

www.daeinstrument.com
CC2030-v3.0 installation guide-1.2us_P2
CC2030
02:81:AO:26:11 2019 S 22000432
S/N :
H/W : F/W : H1.0.1
A01
CC2030
3.0 MAC :
CC2030
02:81:AO:26:11 2019 S 22000432
S/N :
H/W : F/W : H1.0.1
A01
CC2030
3.0 MAC :
02:81:AO:26:11
2019 S 22000432
S/N :
H/W :
F/W : H1.0.1 A01
CC2030
3.0 MAC :
A1
F
Ethernet USB
A2
System Diagram
Connecting Online
LED Status
A1
Steady Lit
Steady Lit (but flashing when transmitting) Server connection and registration succeeded
A2
Fixed IP
Description
Ethernet cable
Red+
White-
Shielded twisted pair UL2464 cable
Make sure that the polarity is properly observed.
Router
Internet
POWER
INPUT
DC12-24V

Hardware & Firmware
A1
F
Ethernet USB
A2
Serial Number
MAC address
Blink DHCP (default)
Off Connection failed over 5 minutes
*Note : Please check back to Step1,Step2, if the A1,A2 lighting status are not shown as above.
−
+
*Note
1.The address of each meter
must be different.
2.Each CC2030 can connect up
to 20 meters
DHCP: No login or password should be needed when connecting online,
if Google can be connected to directly, then the connection is valid for use.
Ethernet cable
Any online network
port may be used
Ethernet cable
Ethernet Port
Router
Router
Step 1 : Test that the network port to be used can connect online
through DHCP (factory default)
Step 2 : Transfer the connection of the Ethernet cable from the
PC to the CC2030
Step 3 : Verify the status LEDs
Any online network
port may be used