Daewoo electricals HEA1187 User manual

Before plugging your unit into the mains, visually check that the unit is
intact and has not suffered any transit damage.

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always
be followed. These instructions should be saved for future reference:
Read and familiarise yourself with all operating instructions before using this
Mini Convector Heater.
Before plugging your unit into the mains, visually check that the unit is intact
and has not suffered any transit damage.
WARNING: In order to avoid overheating, do not cover the heater.
Do not install the appliance directly below an electrical socket.
Do not use this heater with a programmer, timer, separate remote-control
system or any other device that switches the heater on automatically, since a
fire risk exists if the heater is covered or positioned incorrectly.
Do not use this heater with an extension cable.
Check that the voltage indicated on the data plate corresponds with that of the
local network before connecting the appliance to the mains power supply.
Close supervision is required when using this appliance near children.
Never leave this appliance within reach of children.
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
Children of less than 3 years should be kept away unless continuously
supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the
appliance provided that it has been placed or installed in its intended normal
operating position and they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8 years shall not plug in,
regulate and clean the appliance or perform user maintenance.
CAUTION —some parts of this product can become very hot and
cause burns. Particular attention has to be given where children and
vulnerable people are present.
This product shall also not be installed in a bath, shower or a swimming pool
Do not immerse the appliance or its cord in water or any other liquids.
Do not leave the appliance unattended during use.
Do not leave the appliance unattended whilst connected to the mains supply.
Always use this appliance on a solid, level, non-flammable surface.
Do not use this appliance outdoors.
It is imperative to unplug the power cord after the appliance has been used,

before it is cleaned and whilst being repaired.
Repairs to electrical appliances should only be performed by a qualified
electrician. Improper repairs may place user at serious risk.
Do not operate this appliance with a damaged plug or cord, after a malfunction
or after being dropped or damaged in any way.
Regular, periodic checks should be carried out on the mains cable to ensure
no damage is evident. Should there be any signs of damage the appliance
should not be used.
If the power cable is damaged, it should only be replaced by the manufacturer
or a suitable qualified after-sales-service in order to avoid a hazard
Do not allow the mains cable to hang over sharp edges or come in contact with
hot surfaces.
Do not run the mains cable under carpets, rugs, etc.
Allow the unit to cool before storage.
Before cleaning, disconnect the appliance from the mains supply and allow to
cool.
Never place the appliance near to flammable material or high pressure
containers. (e.g., Paper, wood, petrol, solvents, spray canisters etc.)
This appliance is intended for household use only and should not be used for
industrial purposes.
Do not use any accessories or attachments with this appliance other than those
supplied or recommended by supplier.
Do not use this appliance for anything other than its intended use.
Do not push objects into any openings as damage to the appliance and/or
electric shock may occur.
Ensure appliance is situated in an open area, do not allow it to come in contact
with Cupboards, Curtains, wall coverings, clothing or other flammable
materials.
The appliance should not be installed in areas which have a fire-risk, such as
garages, stables or wooden sheds; this is applicable also for rooms in which
highly inflammable gasses or dust can develop. Danger of fire!!
Even at the lowest setting level the unit is in use. In order to switch off the frost
protector pull out the power plug.
Unplug after each use. Grasp the plug, not the cord.
NBDuring the first few minutes of initial use, you may notice a slight
odour and a little smoke. This is normal and will quickly disappear, It is
the coating applied to the heating elements to prevent any corrosion
during transit.

Heat Outlet
Description of parts
Assembling your Mini Convector Heater
Fitting the Feet
Before using this heater, the feet must be fitted to the unit. These are
attached to the base of the heater using the four self-tapping screws
provided, take care to ensure that they are located correctly in the holes at
either end of the base of the appliance:
Rear Mounting Bracket
Heat Indicator Lamp
Adjustable Thermostat
On/Off Switch
Air Inlet
Feet

Wall Mounting Your Mini Convector
Before wall mounting your Mini Convector, please be aware of the minimum
distances from the walls, ceiling and floor as shown below:
Once the desired mounting position has been chosen, fasten the mounting
bracket to the wall as follows.
WARNING Before drilling the wall, ensure that there are no hidden mains
cables or water pipes in the area to be drilled - do not install the appliance
directly below an electrical socket.
Important: this heater must either be wall mounted or have the feet fitted
as described in this manual –under no circumstances should heater be
operated standing directly on the floor or other surface.
1.Remove the bracket from the heater.
2.Draw a horizontal line on the wall in the desired mounting position. Mark two
points 150mm apart along the line where the centre of the screw holes will
be.
3.Use the wall plugs and fixing screws supplied to fix the bracket to the wall.
4.Use a spirit level to ensure that the mounting bracket is fixed horizontally,
adjust the bracket if necessary.
Ceiling
Heater
Wall
Floor
Wall
150mm
Horizontal Line
Screw hole centres

5.Re-attach the heater to the wall bracket.
NB This Mini Convector Heater must not be permanently wired to the mains.
Operating Your Mini Convector Heater
1.Insert the mains plug into the nearest mains socket.
2.Press the On/Off switch at the bottom right hand side to the on position
by pressing ‘I’, the switch will illuminate to show the unit is powered up.
3.Rotate the Thermostat clockwise to increase the room temperature,
rotate anticlockwise to decrease the temperature.
4.The heat indicator lamp will go on and off during use to show that the set
temperature is being maintained –this is quite normal.
Frost Protection
This heater is fitted with an Anti-Frost device, this operates the heater
automatically when the room temperature drops below 10˚C.
Note: The Anti-frost function operates when the thermostat is set to the
lowest level.
Hint on setting the correct temperature
1.Set the heater to the desired heat setting as above.
2.Rotate the Thermostat to the maximum position and allow the room to
warm up. Once the desired room temperature has been reached turn
the Thermostat anticlockwise until the heater just clicks off then turn it
back up clockwise very slightly. The Thermostat will now maintain the
room temperature, if necessary, further increasing or decreasing the
thermostat control may be required to ‘fine tune’ the ideal room
temperature.
Care and Use of your Mini Convector Heater
Always disconnect the heater from the mains power supply before cleaning.
Clean outside of the heater with a clean damp cloth. Never clean with harsh
or abrasive cleaners.
Do not submerge any part of heater in water or any other liquids.
Technical Data
Voltage : 220-240V AC 50Hz
Rated power : 450 W
Model Number : HEA1187

Electrical Connections
This appliance is fitted with a fused three-pin plug to BS 1363. If the plug has
to be removed, it should be cut off and carefully disposed of immediately. To
avoid a possible shock hazard, do not insert the discarded plug into a mains
socket.
Fitting a new plug
The mains lead must be connected as shown below. The wires are coloured
with the following code - Brown wire = Live (L), Blue wire = Neutral (N),
Green & Yellow = Earth (E).
The Blue wire must be connected to the terminal marked N or coloured Black.
The Brown wire must be connected to the terminal marked L or coloured Red.
The Green and Yellow wire must be connected to the terminal marked E or
coloured Green.
Check that there are no cut or stray strands of wire inside the plug.
Use a 13 Amp BS 1362 fuse, only use BSI or ASTA approved fuses.
If you are in any way unsure which plug or fuse to use, always refer to a
qualified electrician.
After replacing or changing a fuse on a moulded plug, the cover must be refitted
to the plug; the appliance must not be used without a fuse cover.
Connect
Brown to
Live (L)
Connect
Green &
Yellow to
Earth (E)
Connect
Blue to
Neutral (N)
Ensure the outer sheath of the mains
lead is securely held by the cable clamp
WARNING: Do not wrap the cord around the heater for storage.