Daikin FTNE15MV14 Installation and operating instructions

DAIKIN ROOM AIR CONDITIONER
PENDINGIN UDARA RUANGAN DAIKIN
OPERATION MANUAL AND
INSTALLATION MANUAL
PANDUAN OPERASI DAN
PANDUAN PEMASANGAN
English
Indonesia
MODELS
FTNE15MV14
FTNE20MV14
FTNE25MV14
FTNE35MV14
FTNE50MV14
FTNE60MV14

1
POWERFUL or POWER CHILL Operation
2
5
9
12
14
15
16
18
21
24
25
26
28
31
37
41

2

3

4

5
(FTNE50/60)
1 2 3
4
5
78
9
11 12 13 14
10
(FTNE15/20/25/35)
1 2 3 10
4
5
79
8
6
14
11
13
12
6

6
(page 14.)
(page 12.)
(page 16.)
Yellow (FTNE15/20/25/35)
Orange (FTNE50/60)
(page 14.)

7
(RNE15/20/25) (RNE35)
(RNE50/60)
(RNE20/25/35/50/60)
*

8
(FTNE15/20/25/35) (FTNE50/60)
1
3
4
6
7
< ARC433A73 >
2
8
10
9
13
5
11
14
12
13. POWERFUL or POWER CHILL button :
• POWERFUL or POWER CHILL
Operation (page 15.)
14. RESET button :
• Restart the unit if it freezes.
• Use a thin object to push.
• Adjusting the Air Flow Direction.
(page 14.)
(page 17.)
(page 16.)
(page 11.)
(page 12.)
        
1
4
2
11
7
6
3
8
13
5
9
<ARC470A13>

9
(FTNE15/20/25/35) (FTNE50/60)
2
3
1
(FTNE15/20/25/35) or front cover (FTNE50/60)
(FTNE15/20/25/35) or front cover (FTNE50/60)

10
(FTNE15/20/25/35)
Remote controller
holder
Set.
To remove, pull it upwards.
Receiver
(FTNE50/60)
(FTNE50/60)

11
1, 3
2
(FTNE50/60)

12
2, 3
1
4
5
(FTNE50/60)(FTNE15/20/25/35)
(FTNE50/60)(FTNE15/20/25/35)
(FTNE50/60)
or
or
(FTNE15/20/25/35)
        
2,3
4
1
5

13
Three levels of airflow rate setting from
“ ” to “ ” plus “ ” are available.
FTNE15/20/25/35
FTNE50/60
Five levels of airflow rate setting from
“ ” to “ ” plus “ ” are available.

14
(FTNE15/20/25/35) (FTNE50/60)
(FTNE15/20/25/35) (FTNE50/60)
“ ” is displayed on the LCD
and the flaps will begin to swing.
“ ” disappears from the LCD.
(FTNE15/20/25/35) (FTNE50/60)
ARC470A13
1,2

15
(FTNE50/60)
POWERFUL or POWER CHILL Operation
To start POWERFUL or
POWER CHILL operation
1. Press “POWERFUL or POWER CHILL
button”.
POWERFUL or POWER CHILL operation
ends in 20 minutes.
Then the system automatically operates
again with the settings which were used
before POWERFUL
or POWER CHILL
operation.
When using POWERFUL or POWER
CHILL
operation, there are some functions
which are not available.
To cancel POWERFUL
or POWER CHILL operation
2. Press “POWERFUL or POWER CHILL button”
again.
“ ” disappears from the LCD.
1,2
“ ” is displayed on the LCD.
NOTE
Notes on POWERFUL or POWER CHILL operation
POWERFUL or POWER CHILL Operation can only be set when the unit is running.
Pressing the operation stop button
In COOL mode
The air flow rate is fixed to the maximum setting.
The temperature and air flow settings are not variable.
In DRY mode
The temperature setting is lowered by 2.0 ~ 2.5°C and the air flow rate is slightly increased.
In FAN mode
The air flow rate is fixed to the maximum setting.
causes the settings to be canceled, and “ ” disappears
from the LCD.
The temperature is set to 18°C. (FTNE15/20/25/35)
(FTNE50/60)
(FTNE15/20/25/35)
ARC470A13
1,2
POWERFUL or POWER CHILL Operation quickly
maximizes the cooling effect in any operation mode.
You can get the maximum capacity.

16
4
2
1, 3
(FTNE50/60)
(FTNE15/20/25/35) (FTNE50/60)
(FTNE15/20/25/35)
(FTNE50/60)
The display disappear from the LCD.
FTNE15/20/25/35
is displayed.
FTNE50/60
TIMER Setting
FTNE50/60
Each pressing of OFF TIMER button
advance the time setting by 1 hour. The
time can be set between 1 to 9 hours.
Press “TIMER Setting button”
until the time setting reaches
the point you like.
ARC470A13
1,2,3
4

17
Displ ay
The display disappear from the LCD.
(FTNE50/60)
2
1, 3
4
(FTNE15/20/25/35)
(FTNE50/60)
Press “TIMER Setting button”
until the time setting reaches
the point you like.
(FTNE15/20/25/35) (FTNE50/60)
is displayed.
FTNE15/20/25/35
FTNE50/60
Each pressing of ON TIMER button
advance the time setting by 1 hour.
The time can be set between 1 to
12 hours.
FTNE50/60
ARC470A13
1,2,3
4

18
(FTNE15/20/25/35) (FTNE50/60)
(FTNE15/20/25/35)
(FTNE50/60)
Open the front panel further while sliding it
to either the left or right and pulling it toward you.
This will disconnect the rotation dowel on one side.
Then disconnect the rotation dowel on the other
side in the same manner.