Daikin ONE DSEN-HAQA User manual

IO-DSEN-HAQA www.daikincomfort.com 02/20
DAIKIN ONE
HOME AIR MONITOR
INSTALLATION AND
OPERATION MANUAL
MODEL
DSEN-HAQA
Only personnel that have been trained to install, adjust, service
or repair (hereinafter, “service”) the equipment specied in this
manual should service the equipment. Daikin will not be
responsible for any injury or property damage arising from
improper service or service procedures. If you service this unit,
you assume responsibility for any injury or property damage
which may result. In addition, in jurisdictions that require one or
more licenses to service the equipment specied in this manual,
only licensed personnel should service the equipment.
Improper installation, adjustment, servicing or repair of the
equipment specied in this manual, or attempting to install,
adjust, service or repair the equipment specied in this manual
without proper training may result in product damage, property
damage, personal injury or death.
WARNING
WARNING
PROP 65 WARNING
FOR CALIFORNIA CONSUMERS
Cancer and Reproductive Harm -
www.P65Warnings.ca.gov

2 www.daikincomfort.com IO-DSEN-HAQA IO-DSEN-HAQA www.daikincomfort.com 3
- Daikin One Home Air Monitor
- Mounting Plate
- Mounting gaskets
- Hole templates
- Mounting screws
❶Assemble material and tools ❷ Choose HVAC duct locaon
❸ Aach mounng plate to duct
- Daikin One Home Air Monitor
- Mounting Plate
- Mounting gaskets
- Hole templates
- Mounting screws
❶Assemble material and tools (cont.)
Descripon
The Daikin One Home Air Monitor is part of the Daikin One
Ecosystem. Used in conjunction with Daikin heating and cooling
equipment and air filters, the Home Air Monitor provides
information about air quality levels, via the Daikin One Smart
Thermostat and its companion mobile application.
The Daikin One Home Air Monitor is meant to be installed by
trusted HVAC service technicians. The following information will
outline the 6-step installation process for the Home Air Monitor.
Proprietary Noce
This document and the information disclosed herein are proprietary
data of Daikin North America LLC. Neither this document nor the
information contained herein shall be reproduced to others without
the written authorization of Daikin North America LLC, except to
the extent required for installation or maintenance of recipient’s
equipment.
Copyright Noce
Copyright 2020, Daikin North America LLC All rights reserved.

2 www.daikincomfort.com IO-DSEN-HAQA IO-DSEN-HAQA www.daikincomfort.com 3
❹ Connect sensor prober to power
❺ Insert sensor probe into mounng plate
❻ Use the Daikin Installer App to connect to WiFi
Regulatory compliance
One
One
One
®
conjunction with a Daikin One+ Smart
a whole house
Thermostat.
and gas phase sensors including an optical partical
counter, temperature, humidity, pressure and VOC
sensors. This device contains a certified third
party wireless module for WiFi and Bluetooth®
communications to transmit data to an access
point such as a consumer router.
Lorem ipsum
This device has been tested and found to comply with FCC and
ISED requirements for RF Exposure when operated with at least
20cm separation from the antenna.
Daikin is not responsible for any changes or modifications not
expressly approved by the party responsible for compliance.
Such modifications could void the user’s authority to operate
the equipment.
This device complies with Industry Canada’s license-exempt
RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must
accept any interference, including interference that may cause
undesired operation of the device.
This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
further assistance.
CLASS 1 LASER PRODUCT
WARNING
Contains FCC ID: 2ANU9HAVENA
Contains IC: 23327-HAVENA
PROP 65 WARNING
FOR CALIFORNIA CONSUMERS
WARNING
Cancer and Reproductive Harm —
www.P65Warnings.ca.gov.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc., and any use of such marks are under license.

Our connuing commitment to quality products may mean a change in specicaons without noce.
©2020 • Houston, Texas • Printed in the USA
4 IO-DSEN-HAQA
Maintenance
The Daikin One Home Air Monitor requires very little maintenance.
However, periodic inspection and cleaning of the air passageways
in the sensor probe will help to keep the detection sensors and
surfaces free of particles which, if left to build up, could cause
inaccurate reporting of the airborne particulates in the home’s air.
CAUTION:
If you are not a qualified electrician of HVAC technician, or are not
comfortable and/or familiar with electrical power supplies, contact
your HVAC dealer to service this monitor.
To clean the Daikin One Home Air Monitor, first remove power
from the sensor probe by disconnecting the 24V supply wire from
its transformer.
Carefully pull the sensor probe out of ductwork, but leave the
mounting plate in place. Once the sensor probe is free of the
ductwork, carefully inspect the two passageways in the probe for
any visible particulate buildup on the internal surfaces.
If there is nothing visible, carefully reinsert the sensor probe
into the hole in the mounting plate just until you hear a
slight “click”. Do not push the sensor probe in further than
this “click” position. Reattach the supply of 24V power to
the sensor probe. When the sensor probe’s LED light turns
solid blue (not flashing), then the device is back online
and operating.
If there is visible debris collected on the internal surfaces, take a
cotton swab that has been wet slightly with isopropyl or rubbing
alcohol and very gently wipe over the internal surfaces of the
sensor probe to remove the debris. Carefully reinsert the sensor
probe into the hole in the mounting plate just until you hear a
slight “click”. Do not push the sensor probe in further than this
“click” position. Reattach the supply of 24V power to the sensor
probe. When the sensor probe’s LED light turns solid blue (not
flashing), then the device is back online and operating.
If you have any questions or concerns about this device’s
maintenance, please call 1-855-DAIKIN1 for assistance.