Daikin EWAP/EWYP 060-260 Owner's manual

Packaged air-cooled water chillers
EWAP/EWYP 060-260
Installation-Operation-Maintenance 2
Installation Fonctionnement Entretien 32
Instalación Funcionamiento Mantenimiento 62
Installazione Funzionamento Manutenzione 92
Installation Betrieb Wartung 122
Telepítés - Üzemeltetés - Karbantartás 152
Instalace Provoz Údržba 182
Εγκατάσταση Λειτυργία Συντήρηση 212
Installatie Werking Onderhoud 242
Instalacja Eksploatacja Konserwacja 272
Instalação Funcionamento Manutenção 302
Установка – Эксплуатация – Техническое обслуживание 332
Installation Drift Underhåll 362

Safety recommendations
To avoid death, injury, equipment or
property damage, the following
recommendations should be
observed during maintenance and
service visits:
1.The maximum allowable
pressures for system leak testing
on low and high pressure side
are given in the chapter
"Installation". Always provide a
pressure regulator.
2. Disconnect the main power
supply before any servicing on
the unit.
3. Service work on the refrigeration
system and the electrical system
should be carried out only by
qualified and experienced
personnel.
Foreword
These instructions are given as a
guide to good practice in the
installation, start-up, operation, and
maintenance by the user, of Daikin
EWAP/EWYP chillers.They do not
contain full service procedures
necessary for the continued
successful operation of this
equipment.The services of a
qualified technician should be
employed through the medium of a
maintenance contract with a
reputable service company. Read
this manual thoroughly before unit
start-up.
Units are assembled, pressure
tested, dehydrated, charged and run
tested before shipment.
Warnings and cautions
Warnings and Cautions appear at
appropriate sections throughout
this manual.Your personal safety
and the proper operation of this
machine require that you follow
them carefully.The constructor
assumes no liability for installations
or servicing performed by
unqualified personnel.
WARNING! : Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION! : Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury. It may also be
used to alert against unsafe
practices or for equipment or
property-damage-only accidents.
2CG-SVX04C-E4
General information

CG-SVX04C-E4 3
General information
Warranty
Warranty is based on the general
terms and conditions of the
manufacturer.The warranty is void
if the equipment is repaired or
modified without the written
approval of the manufacturer, if the
operating limits are exceeded or if
the control system or the electrical
wiring is modified. Damage due to
misuse, lack of maintenance or
failure to comply with the
manufacturer's instructions or
recommendations is not covered by
the warranty obligation. If the user
does not conform to the rules of
this manual, it may entail
cancellation of warranty and
liabilities by the manufacturer.
Refrigerant
The refrigerant provided by the
manufacturer meets all the
requirements of our units. When
using recycled or reprocessed
refrigerant, it is advisable to ensure
its quality is equivalent to that of a
new refrigerant. For this, it is
necessary to have a precise analysis
made by a specialized laboratory. If
this condition is not respected, the
manufacturer warranty could be
cancelled.
Reception
On arrival, inspect the unit before
signing the delivery note.
Reception in France only:
In case of visible damage:The
consignee (or the site
representative) must specify any
damage on the delivery note, legibly
sign and date the delivery note, and
the truck driver must countersign it.
The consignee (or the site
representative) must notify Daikin
and send a copy of the delivery
note.The customer (or the site
representative) should send a
registered letter to the last carrier
within 3 days of delivery.
Note: for deliveries in France, even
concealed damage must be looked
for at delivery and immediately
treated as visible damage.
Reception in all countries except
France:
In case of concealed damage:The
consignee (or the site
representative) must send a
registered letter to the last carrier
within 7 days of delivery, claiming
for the described damage. A copy of
this letter must be sent to Daikin.

4CG-SVX04C-E4
General information
Training
To assist you in obtaining the best
use of it and maintaining it in
perfect operating condition over a
long period of time, the
manufacturer has at your disposal a
refrigeration and air conditioning
service school. The principal aim of
this is to give operators and
technicians a better knowledge of
the equipment they are using, or
that is under their charge. Emphasis
is particularly given to the
importance of periodic checks on
the unit operating parameters as
well as on preventive maintenance,
which reduces the cost of owning
the unit by avoiding serious and
costly breakdown.
Maintenance contract
It is strongly recommended that
you sign a maintenance contract
with your local Service Agency. This
contract provides regular
maintenance of your installation by
a specialist in our equipment.
Regular maintenance ensures that
any malfunction is detected and
corrected in good time and
minimizes the possibility that
serious damage will occur. Finally,
regular maintenance ensures the
maximum operating life of your
equipment. We would remind you
that failure to respect these
installation and maintenance
instructions may result in
immediate cancellation of the
warranty.

CG-SVX04C-E4 5
Contents
General information 2
Installation
General data 6
General unit characteristics 15
Unit nameplate 15
Installation instructions 15
Handling 15
Minimal installation water content 18
Water treatment 20
Antifreeze protection 20
Electrical connections 20
General start-up
Preparation 22
Start-up 22
Operation
Control and unit operation 27
Weekly start up and week-end shutdown 27
Start-up and seasonal shutdown 27
Maintenance
Maintenance instructions 28
Installation checklist 29
Troubleshooting guide 30

6CG-SVX04C-E4
General Data
Table 1 - EWAP Cooling only - Standard version - R407C
EWAP EWAP EWAP EWAP EWAP
060 080 100 120 125
Eurovent Performances (1)
Net Cooling Capacity (kW) 62.5 76.2 102.8 121.8 132.3
Total Power input in cooling (kW) 24.4 28.8 38.7 43.6 50.5
Water pressure drop (kPa) 33 38 46 43 44
Pressure available (5) (kPa) 180 173 139 195 181
Main Power supply 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50
Units Amps
Nominal (4) (A) 57 69 89 102 111
Start-up Amps (A) 203 215 236 327 336
Short circuit unit capacity (kA) 10 10 10 10 10
Max supply cable size (mm²) 35 35 95 95 95
Min supply cable size (mm²) 16 16 50 50 50
Compressor
Number 22322
Type Scroll Scroll Scroll Scroll Scroll
Model (10T+15T) (15T+15T) (15T+15T+10T) (20T+25T) (25T+25T)
Rated Amps (4) (A) 19+28.5 28.5+28.5 28.5+28.5+19 38+47 47+47
Locked rotor Amps (2) (A) 175 175 175 272 272
Motor RPM (rpm) 2900 2900 2900 2900 2900
Power factor 0.85 0.85 0.85 0.87 0.87
Sump Heater (2) (W) 160 160 160 150 150
Evaporator
Number 11111
Type Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate
Water volume (total) (l) 6.8 8.2 10.5 11.3 12.6
Antifreeze Heater (W) 115 115 115 115 115
Unit Water Connections Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7
Water Connections Diameter 2" 2 1/2" 2 1/2" 2 1/2" 2 1/2"
Coil
Type Slit Fin Slit Fin Slit Fin Slit Fin Slit Fin
Length (mm) 2489 2896 2896 2896 2896
Height (mm) 1422 1422 1626 1626 1626
Face Area (3) (m²) 3.54 4.12 4.71 4.71 4.71
Rows 33344
Fins per foot (fpf) 180 180 180 168 168
Fan
Type Propeller Propeller Propeller Propeller Propeller
Number 23333
Diameter (mm) 710 710 800 800 800
Drive type Direct drive Direct drive Direct drive Direct drive Direct drive
Air flow (m3/h) 19100 26300 37300 37100 37100
Numberofmotors 23333
Motor HP (2) (kW) 0.57 0.57 1.05 1.05 1.05
Rated Amps (2) (A) 1.5 1.5 2.4 2.4 2.4
Motor RPM (rpm) 700 700 680 680 680
Dimensions
Height (6) (mm) 1897 1897 2074 2074 2074
Length (mm) 2800 3200 3200 3200 3200
Wi dt h (m m) 110 0 110 0 110 0 110 0 110 0
Operating Weight (kg) 842 968 1143 1267 1292
Shipping Weight (kg) 834 954 1124 1260 1284
System Data
Numberofrefrigerantcircuits 11111
Capacity steps 22222
Minimum capacity (%) 40/60 50 37/63 37/63 37/63
Refrigerant Charge (3)
CircuitA (kg)1821242828
CircuitB (kg)-----
(1) at Eurovent Conditions (Evap 12°C/7°C - Air. 35°C)
(2) per motor
(3) per circuit
(4) Max rated conditions.
(5) Dual Pump Option
(6) For units with HESP option, contact your local sales office

CG-SVX04C-E4 7
Table 1 - cont
EWAP EWAP EWAP EWAP EWAP EWAP
130 160 180 210 240 260
Eurovent Performances (1)
Net Cooling Capacity (kW) 128.9 157.1 182.8 214.2 241.3 267.0
Total Power input in cooling (kW) 49.1 57.9 68.4 77.9 88.3 102.4
Water pressure drop (kPa) 30 36 30 35 35 41
Pressure available (5) (kPa) 206 185 196 174 137 124
Main Power supply 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50
Units Amps
Nominal (4) (A) 113 136 153 188 208 225
Start-up Amps (A) 259 282 300 334 354 450
Short circuit unit capacity (kA) 10 10 10 10 10 10
Max supply cable size (mm²) 95 95 150 150 150 150
Min supply cable size (mm²) 50 50 95 95 95 95
Compressor
Number 4 4 6 6 6 4
Type Scroll Scroll Scroll Scroll Scroll Scroll
Model (10T+15T) (15T+15T) (10T+10T+15T) (15T+15T+10T) (15T+15T+15T) (25T+25T)
Rated Amps (4) (A) 2x(19+28.5) 2x(28.5+28.5) 2x(19+19+28.5) 2x(28.5+28.5+19) 2x(28.5+28.5+28.5) 2x(47+47)
Locked rotor Amps (2) (A) 175 175 175 175 175 272
Motor RPM (rpm) 2900 2900 2900 2900 2900 2900
Power factor 0.85 0.85 0.85 0.85 0.85 0.87
Sump Heater (2) (W) 160 160 160 160 160 150
Evaporator
Number 1 1 1 1 1 1
Type Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate
Water volume (total) (l) 17.2 19.8 25.6 29.0 35.7 35.7
Antifreeze Heater (W) 180 180 180 180 180 180
Unit Water Connections Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7
Water Connections Diameter 2 1/2" 2 1/2" 3" 3" 3" 3"
Coil
Type Slit Fin Slit Fin Slit Fin Slit Fin Slit Fin Slit Fin
Length (mm) 2489 2896 2896 2896 2896 2896
Height (mm) 1422 1422 1626 1626 1626 1626
Face Area (3) (m²) 3.54 4.12 4.71 4.71 4.71 4.71
Rows 333 3 44
Fins per foot (fpf) 180 180 180 180 180 168
Fan
Type Propeller Propeller Propeller Propeller Propeller Propeller
Number 4 6 6 6 6 6
Diameter (mm) 710 710 710 800 800 800
Drive type Direct drive Direct drive Direct drive Direct drive Direct drive Direct drive
Air flow (m3/h) 38300 52700 55400 86300 83000 79300
Number of motors 4 6 6 6 6 6
Motor HP (2) (kW) 0.57 0.57 0.57 1.4 1.4 1.4
Rated Amps (2) (A) 1.5 1.5 1.5 4 4 4
Motor RPM (rpm) 700 700 700 680 680 680
Dimensions
Height (6) (mm) 1897 1897 2100 2100 2100 2100
Length (mm) 3400 3400 3400 3400 3400 3400
Width (mm) 2300 2300 2300 2300 2300 2300
Operating Weight (kg) 1623 1818 2087 2245 2423 2456
Shipping Weight (kg) 1588 1778 2030 2181 2344 2377
System Data
Number of refrigerant circuits 2 2 2 2 2 2
Capacity steps 4 4 4 4 4 4
Minimum capacity (%) 20/30 25 22/29 19/32 17/33 17/33
Refrigerant Charge (3)
Circuit A (kg) 19 22 27 27 34 31
Circuit B (kg) 19 22 27 27 34 31
(1) at Eurovent Conditions (Evap 12°C/7°C - Air. 35°C)
(2) per motor
(3) per circuit
(4) Max rated conditions.
(5) Dual Pump Option
(6) For units with HESP option, contact your local sales office
General Data

8CG-SVX04C-E4
General Data
Table 2 - EWAP cooling only - Super Quiet version - R407C
EWAP EWAP EWAP EWAP EWAP
060 080 100 120 125
Eurovent Performances (1)
Net Cooling Capacity (kW) 62.2 75.7 101.9 121.8 132.3
Total Power input in cooling (kW) 24.2 28.4 36.4 43.6 50.5
Water pressure drop (kPa) 32 37 45 43 44
Pressure available (5) (kPa) 180 174 141 195 181
Main Power supply 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50
Units Amps
Nominal (4) (A) 55 66 90 102 111
Start-up Amps (A) 202 213 236 327 336
Short circuit unit capacity (kA) 10 10 10 10 10
Max supply cable size (mm²) 35 35 95 95 95
Min supply cable size (mm²) 16 16 50 50 50
Compressor
Number 22322
Type Scroll Scroll Scroll Scroll Scroll
Model (10T+15T) (15T+15T) (15T+15T+10T) (20T+25T) (25T+25T)
Rated Amps (2)(4) (A) 19+28.5 28.5+28.5 28.5+28.5+19 38+47 47+47
Locked rotor Amps (2) (A) 175 175 175 272 272
Motor RPM (rpm) 2900 2900 2900 2900 2900
Power factor 0.85 0.85 0.85 0.87 0.87
Sump Heater (2) (W) 160 160 160 150 150
Evaporator
Number 11111
Type Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate
Water volume (total) (l) 6.8 8.2 10.5 11.3 12.6
Antifreeze Heater (W) 115 115 115 115 115
Unit Water Connections Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7
Water Connections Diameter 2" 2 1/2" 2 1/2" 2 1/2" 2 1/2"
Coil
Type Slit Fin Slit Fin Slit Fin Slit Fin Slit Fin
Length (mm) 2489 2896 2896 2896 2896
Height (mm) 1422 1422 1626 1626 1626
Face Area (3) (m²) 3.54 4.12 4.71 4.71 4.71
Rows 33344
Fins per foot (fpf) 180 180 180 168 168
Fan
Type Propeller Propeller Propeller Propeller Propeller
Number 23333
Diameter (mm) 710 710 800 800 800
Drive type Direct drive Direct drive Direct drive Direct drive Direct drive
Air flow (m3/h) 19100 26300 37300 37100 37100
MotorsNumber 23333
Motor HP (2) (kW) 0.57 0.57 1.05 1.05 1.05
Rated Amps (2) (A) 1.5 1.5 2.4 2.4 2.4
Motor RPM (rpm) 700 700 680 680 680
Dimensions
Height (6) (mm) 1897 1897 2048 2048 2048
Length (mm) 2800 3200 3200 3200 3200
Wi dt h (m m) 110 0 110 0 110 0 110 0 110 0
Operating Weight (kg) 872 1010 1155 1279 1304
Shipping Weight (kg) 864 996 1136 1272 1296
System Data
Refrigerantcircuit 11111
Capacity steps 22222
Minimum capacity (%) 40/60 50 37/63 37/63 37/63
Refrigerant Charge (3)
CircuitA (kg)1821242828
CircuitB (kg)-----
(1) at Eurovent Conditions (Evap 12°C/7°C - Air. 35°C)
(2) per motor
(3) per circuit
(4) Max rated conditions.
(5) Dual Pump Option
(6) For units with HESP option, contact your local sales office

CG-SVX04C-E4 9
General Data
Table 2 cont
EWAP EWAP EWAP EWAP EWAP EWAP
130 160 180 210 240 260
Eurovent Performances (1)
Net Cooling Capacity (kW) 128.1 156.1 181.5 212.1 238.0 264.9
Total Power input in cooling (kW) 48.8 57.2 68.0 73.4 85.0 102.1
Water pressure drop (kPa) 29 36 29 34 34 40
Pressure available (5) (kPa) 207 186 197 176 139 126
Main Power supply 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50
Units Amps
Nominal (4) (A) 110 131 150 178 200 216
Start-up Amps (A) 256 278 295 324 344 441
Short circuit unit capacity (kA) 10 10 10 10 10 10
Max supply cable size (mm²) 95 95 150 150 150 150
Min supply cable size (mm²) 50 50 95 95 95 95
Compressor
Number 4 4 6 6 6 4
Type Scroll Scroll Scroll Scroll Scroll Scroll
Model (10T+15T) (15T+15T) (10T+10T+15T) (15T+15T+10T) (15T+15T+15T) (25T+25T)
Rated Amps (2)(4) (A) 2x(19+28.5) 2x(28.5+28.5) 2x(19+19+28.5) 2x(28.5+28.5+19) 2x(28.5+28.5+28.5) 2x(47+47)
Locked rotor Amps (2) (A) 175 175 175 175 175 272
Motor RPM (rpm) 2900 2900 2900 2900 2900 2900
Power factor 0.85 0.85 0.85 0.85 0.85 0.87
Sump Heater (2) (W) 160 160 160 160 160 150
Evaporator
Number 1 1 1 1 1 1
Type Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate
Water volume (total) (l) 17.2 19.8 25.6 29.0 35.7 35.7
Antifreeze Heater (W) 180 180 180 180 180 180
Unit Water Connections Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7
Water Connections Diameter 2 1/2" 2 1/2" 3" 3" 3" 3"
Coil
Type Slit Fin Slit Fin Slit Fin Slit Fin Slit Fin Slit Fin
Length (mm) 2489 2896 2896 2896 2896 2896
Height (mm) 1422 1422 1626 1626 1626 1626
Face Area (3) (m²) 3.54 4.12 4.71 4.71 4.71 4.71
Rows 3333 44
Fins per foot (fpf) 180 180 180 180 180 168
Fan
Type Propeller Propeller Propeller Propeller Propeller Propeller
Number 466666
Diameter (mm) 710 710 710 800 800 800
Drive type Direct drive Direct drive Direct drive Direct drive Direct drive Direct drive
Air flow (m3/h) 38300 52700 55400 74700 71400 74300
MotorsNumber 466666
Motor HP (2) (kW) 0.57 0.57 0.57 1.05 1.05 1.05
Rated Amps (2) (A) 1.5 1.5 1.5 2.4 2.4 2.4
Motor RPM (rpm) 700 700 700 680 680 680
Dimensions
Height (6) (mm) 1897 1897 2100 2074 2074 2074
Length (mm) 3400 3400 3400 3400 3400 3400
Width (mm) 2300 2300 2300 2300 2300 2300
Operating Weight (kg) 1685 1900 2171 2335 2513 2546
Shipping Weight (kg) 1650 1860 2114 2271 2434 2467
System Data
Refrigerant circuit 2 2 2 2 2 2
Capacity steps 4 4 4 4 4 4
Minimum capacity (%) 20/30 25 22/29 19/32 17/33 17/33
Refrigerant Charge (3)
Circuit A (kg) 19 22 27 27 34 31
Circuit B (kg) 19 22 27 27 34 31
(1) at Eurovent Conditions (Evap 12°C/7°C - Air. 35°C)
(2) per motor
(3) per circuit
(4) Max rated conditions.
(5) Dual Pump Option
(6) For units with HESP option, contact your local sales office

10 CG-SVX04C-E4
Table 3 - EWYP reversible - Standard version - R407C
EWAP EWAP EWAP EWAP EWAP
060 080 100 120 125
Eurovent Performances (1)
Net Cooling Capacity (kW) 60.8 73.6 94.5 116.4 124.8
Total Power input in cooling (kW) 25.4 30.1 40.0 42.8 49.7
Water pressure drop in cooling (kPa) 31 35 39 40 39
Pressure available in cooling (5) (kPa) 183 177 156 201 190
Net Heating Capacity (kW) 59.6 72.7 99.2 112.3 120.3
Power input in heating (kW) 24.9 30.4 43.0 45.7 48.7
Pressure drop in heating (kPa) 30 35 43 37 36
Pressure available in heating (5) (kPa) 185 179 146 205 195
Main Power supply 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50
Units Amps
Nominal (4) (A) 57 69 89 89 89
Start-up Amps (A) 203 215 236 236 236
Short circuit unit capacity (kA) 10 10 10 10 10
Max supply cable size (mm²) 35 35 95 95 95
Min supply cable size (mm²) 16 16 50 50 50
Compressor
Number 22333
Type Scroll Scroll Scroll Scroll Scroll
Model (10T+15T) (15T+15T) (15T+15T+10T) (15T+15T+10T) (15T+15T+10T)
Rated Amps (2)(4) (A) 19+28.5 28.5+28.5 28.5+28.5+18.5 28.5+28.5+18.6 28.5+28.5+18.7
Locked rotor Amps (2) (A) 175 175 175 176 177
Motor RPM (rpm) 2900 2900 2900 2900 2900
Power factor 0.85 0.85 0.85 0.87 0.87
Sump Heater (2) (W) 160 160 50 50 50
Evaporator
Number 11111
Type Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate
Water volume (total) (l) 6.8 8.2 10.5 10.5 10.5
Antifreeze Heater (W) 115 115 115 115 115
Unit Water Connections Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7
Water Connections Diameter 2" 2 1/2" 2 1/2" 2 1/2" 2 1/2"
Coil
Type Plate Fin Plate Fin Plate Fin Slit Fin Slit Fin
Length (mm) 2489 2896 2896 2896 2896
Height (mm) 1422 1422 1626 1626 1626
Face Area (3) (m²) 3.54 4.12 4.71 4.71 4.71
Rows 33344
Fins per inch (fpf) 204 204 204 168 168
Fan
Type Propeller Propeller Propeller Propeller Propeller
Number 23333
Diameter (mm) 710 710 800 800 800
Drive type Direct drive Direct drive Direct drive Direct drive Direct drive
Air flow (m3h) 19100 26300 37300 37100 37300
MotorsNumber 23333
Motor HP (2) (kW) 0.57 0.57 1.05 1.05 1.05
Rated Amps (2) (A) 1.5 1.5 2.4 2.4 2.4
Motor RPM (rpm) 700 700 680 680 680
Dimensions
Height (6) (mm) 1897 1897 2048 2048 2048
Length (mm) 2800 3200 3200 3200 3200
Wi dt h (m m) 110 0 110 0 110 0 110 0 110 0
Operating Weight (kg) 870 996 1182 1302 1331
Shipping Weight (kg) 862 982 1163 1295 1323
System Data
Refrigerantcircuit 11111
Capacity steps 22222
Minimum capacity (%) 40/60 50 37/63 37/64 37/65
Refrigerant Charge (3)
CircuitA (kg)1821244040
CircuitB (kg)-----
(1) at Eurovent Conditions (Cooling :Water 12°C/7°C - Air. 35°C // Heating :Water 40°C/45°C - Air. DB7°C / WB6°C)
(2) per motor
(3) per circuit
(4) Max rated conditions.
(5) Dual Pump Option
(6) For units with HESP option, contact your local sales office
General Data

CG-SVX04C-E4 11
General Data
Table 3 cont
EWYP EWYP EWYP EWYP EWYP EWYP
130 160 180 210 240 260
Eurovent Performances (1)
Net Cooling Capacity (kW) 125.9 153.1 167.4 195.1 220.7 251.9
Total Power input in cooling (kW) 51.1 60.7 69.8 78.2 90.1 102.0
Water pressure drop in cooling (kPa) 28 35 25 29 29 36
Pressure available in cooling (5) (kPa) 209 189 208 191 148 134
Net Heating Capacity (kW) 119.2 145.3 171.8 198.4 220.0 251.6
Power input in heating (kW) 49.5 60.4 69.6 84.5 92.6 101.1
Pressure drop in heating (kPa) 25 31 26 30 29 36
Pressure available in heating (5) (kPa) 214 197 205 188 149 134
Main Power supply 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50
Units Amps
Nominal (4) (A) 113 136 153 188 208 225
Start-up Amps (A) 259 282 300 334 354 450
Short circuit unit capacity (kA) 10 10 10 10 10 10
Max supply cable size (mm²) 95 95 150 150 150 150
Min supply cable size (mm²) 50 50 95 95 95 95
Compressor
Number 4 4 6 6 6 4
Type Scroll Scroll Scroll Scroll Scroll Scroll
Model (10T+15T) (15T+15T) (10T+10T+15T) (15T+15T+10T) (15T+15T+15T) (25T+25T)
Rated Amps (2)(4) (A) 2x(19+28.5) 2x(28.5+28.5) 2x(19+19+28.5) 2x(28.5+28.5+19) 2x(28.5+28.5+28.5) 2x(47+47)
Locked rotor Amps (2) (A) 175 175 175 175 175 272
Motor RPM (rpm) 2900 2900 2900 2900 2900 2900
Power factor 0.85 0.85 0.85 0.85 0.85 0.87
Sump Heater (2) (W) 160 160 160 160 160 150
Evaporator
Number 1 1 1 1 1 1
Type Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate
Water volume (total) (l) 17.2 19.8 25.6 29.0 35.7 35.7
Antifreeze Heater (W) 180 180 180 180 180 180
Unit Water Connections Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7
Water Connections Diameter 2 1/2" 2 1/2" 3" 3" 3" 3"
Coil
Type Plate Fin Plate Fin Plate Fin Plate Fin Plate Fin Slit Fin
Length (mm) 2489 2896 2896 2896 2896 2896
Height (mm) 1422 1422 1626 1626 1626 1626
Face Area (3) (m²) 3.54 4.12 4.71 4.71 4.71 4.71
Rows 3 3 3 3 4 4
Fins per inch (fpf) 204 204 204 204 180 168
Fan
Type Propeller Propeller Propeller Propeller Propeller Propeller
Number 4 6 6 6 6 6
Diameter (mm) 710 710 710 800 800 800
Drive type Direct drive Direct drive Direct drive Direct drive Direct drive Direct drive
Air flow (m3/h) 38300 52700 55400 86300 83000 79300
Motors Number 4 6 6 6 6 6
Motor HP (2) (kW) 0.57 0.57 0.57 1.4 1.4 1.4
Rated Amps (2) (A) 1.5 1.5 1.5 4 4 4
Motor RPM (rpm) 700 700 700 680 680 680
Dimensions
Height (6) (mm) 1897 1897 2100 2100 2100 2100
Length (mm) 3400 3400 3400 3400 3400 3400
Width (mm) 2300 2300 2300 2300 2300 2300
Operating Weight (kg) 1677 1872 2166 2324 2502 2535
Shipping Weight (kg) 1642 1832 2109 2260 2423 2456
System Data
Refrigerant circuit 2 2 2 2 2 2
Capacity steps 4 4 4 4 4 4
Minimum capacity (%) 20/30 25 22/29 19/32 17/33 17/33
Refrigerant Charge (3)
Circuit A (kg) 21 24 29 30 37 41
Circuit B (kg) 21 24 29 30 37 41
(1) at Eurovent Conditions (Cooling :Water 12°C/7°C - Air. 35°C // Heating :Water 40°C/45°C - Air. DB7°C / WB6°C)
(2) per motor
(3) per circuit
(4) Max rated conditions.
(5) Dual Pump Option
(6) For units with HESP option, contact your local sales office

12 CG-SVX04C-E4
General Data
Table 4 - EWYP reversible - Super Quiet version - R407C
EWYP EWYP EWYP EWYP EWYP
060 080 100 120 125
Eurovent Performances (1)
Net Cooling Capacity (kW) 60.4 73.1 93.6 116.4 124.8
Total Power input in cooling (kW) 25.2 29.8 37.6 42.8 49.7
Water pressure drop in cooling (kPa) 31 35 38 40 39
Pressure available in cooling (5) (kPa) 183 178 158 201 190
Net Heating Capacity (kW) 59.6 72.7 99.2 112.3 120.3
Power input in heating (kW) 24.2 29.3 39.8 45.7 48.7
Pressure drop in heating (kPa) 30 35 43 37 36
Pressure available in heating (5) (kPa) 185 179 146 205 195
Main Power supply 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50
Units Amps
Nominal (4) (A) 55 66 90 102 111
Start-up Amps (A) 202 213 236 327 336
Short circuit unit capacity (kA) 10 10 10 10 10
Max supply cable size (mm²) 35 35 95 95 95
Min supply cable size (mm²) 16 16 50 50 50
Compressor
Number 22322
Type Scroll Scroll Scroll Scroll Scroll
Model (10T+15T) (15T+15T) (15T+15T+10T) (20T+25T) (25T+25T)
Rated Amps (2)(4) (A) 19+28.5 28.5+28.5 28.5+28.5+19 38+47 47+47
Locked rotor Amps (2) (A) 175 175 175 272 272
Motor RPM (rpm) 2900 2900 2900 2900 2900
Power factor 0.85 0.85 0.85 0.87 0.87
Sump Heater (2) (W) 160 160 160 150 150
Evaporator
Number 11111
Type Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate
Water volume (total) (l) 6.8 8.2 10.5 11.3 12.6
Antifreeze Heater (W) 115 115 115 115 115
Unit Water Connections Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7
Water Connections Diameter 2" 2 1/2" 2 1/2" 2 1/2" 2 1/2"
Coil
Type Plate Fin Plate Fin Plate Fin Slit Fin Slit Fin
Length (mm) 2489 2896 2896 2896 2896
Height (mm) 1422 1422 1626 1626 1626
Face Area (3) (m²) 3.54 4.12 4.71 4.71 4.71
Rows 33344
Fins per inch (fpf) 204 204 204 168 168
Fan
Type Propeller Propeller Propeller Propeller Propeller
Number 23333
Diameter (mm) 710 710 800 800 800
Drive type Direct drive Direct drive Direct drive Direct drive Direct drive
Air flow (m3/h) 19100 26300 37300 37100 37100
MotorsNumber 23333
Motor HP (2) (kW) 0.57 0.57 1.05 1.05 1.05
Rated Amps (2) (A) 1.5 1.5 2.4 2.4 2.4
Motor RPM (rpm) 700 700 680 680 680
Dimensions
Height (6) (mm) 1897 1897 2048 2048 2048
Length (mm) 2800 3200 3200 3200 3200
Wi dt h (m m) 110 0 110 0 110 0 110 0 110 0
Operating Weight (kg) 900 1038 1194 1314 1343
Shipping Weight (kg) 892 1024 1175 1307 1335
System Data
Refrigerantcircuit 11111
Capacity steps 22222
Minimum capacity (%) 40/60 50 37/63 37/63 37/63
Refrigerant Charge (3)
CircuitA (kg)1821244040
CircuitB (kg)-----
(1) at Eurovent Conditions (Cooling: Water 12°C/7°C - Air. 35°C / Heating: Water 40°C/45°C - Air. DB7°C / WB6°C)
(2) per motor
(3) per circuit
(4) Max rated conditions.
(5) Dual Pump Option
(6) For units with HESP option, contact your local sales office

CG-SVX04C-E4 13
General Data
Table 4 cont
EWYP EWYP EWYP EWYP EWYP EWYP
130 160 180 210 240 260
Eurovent Performances (1)
Net Cooling Capacity (kW) 125.5 152.5 166.8 194.1 219.2 250.0
Total Power input in cooling (kW) 50.9 60.3 69.6 75.9 88.3 101.5
Water pressure drop in cooling (kPa) 28 34 25 29 29 36
Pressure available in cooling (5) (kPa) 209 190 209 192 149 135
Net Heating Capacity (kW) 119.2 145.3 171.8 198.4 220.0 251.6
Power input in heating (kW) 48.5 59.0 68.2 79.5 87.6 97.4
Pressure drop in heating (kPa) 25 31 26 30 29 36
Pressure available in heating (5) (kPa) 214 197 205 188 149 134
Main Power supply 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50 400/3/50
Units Amps
Nominal (4) (A) 110 131 150 178 200 216
Start-up Amps (A) 256 278 295 324 344 441
Short circuit unit capacity (kA) 10 10 10 10 10 10
Max supply cable size (mm²) 95 95 150 150 150 150
Min supply cable size (mm²) 50 50 95 95 95 95
Compressor
Number 446 6 64
Type Scroll Scroll Scroll Scroll Scroll Scroll
Model (10T+15T) (15T+15T) (10T+10T+15T) (15T+15T+10T) (15T+15T+15T) (25T+25T)
Rated Amps (2)(4) (A) 2x(19+28.5) 2x(28.5+28.5) 2x(19+19+28.5) 2x(28.5+28.5+19) 2x(28.5+28.5+28.5) 2x(47+47)
Locked rotor Amps (2) (A) 175 175 175 175 175 272
Motor RPM (rpm) 2900 2900 2900 2900 2900 2900
Power factor 0.85 0.85 0.85 0.85 0.85 0.87
Sump Heater (2) (W) 160 160 160 160 160 150
Evaporator
Number 111 1 11
Type Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate Brazed plate
Water volume (total) (l) 17.2 19.8 25.6 29.0 35.7 35.7
Antifreeze Heater (W) 180 180 180 180 180 180
Unit Water Connections Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7 Male ISO R7
Water Connections Diameter 2 1/2" 2 1/2" 3" 3" 3" 3"
Coil
Type Slit Fin Slit Fin Slit Fin Slit Fin Slit Fin Slit Fin
Length (mm) 2489 2896 2896 2896 2896 2896
Height (mm) 1422 1422 1626 1626 1626 1626
Face Area (3) (m²) 3.54 4.12 4.71 4.71 4.71 4.71
Rows 333 3 44
Fins per inch (fpf) 204 204 204 204 180 168
Fan
Type Propeller Propeller Propeller Propeller Propeller Propeller
Number 466 6 66
Diameter (mm) 710 710 710 800 800 800
Drive type Direct drive Direct drive Direct drive Direct drive Direct drive Direct drive
Air flow (m3/h) 38300 52700 55400 74700 71400 74300
Motors Number 4 6 6 6 6 6
Motor HP (2) (kW) 0.57 0.57 0.57 1.05 1.05 1.05
Rated Amps (2) (A) 1.5 1.5 1.5 2.4 2.4 2.4
Motor RPM (rpm) 700 700 700 680 680 680
Dimensions
Height (6) (mm) 1897 1897 2100 2074 2074 2074
Length (mm) 3400 3400 3400 3400 3400 3400
Width (mm) 2300 2300 2300 2300 2300 2300
Operating Weight (kg) 1739 1954 2250 2414 2592 2625
Shipping Weight (kg) 1704 1914 2193 2350 2513 2546
System Data
Refrigerant circuit 2 2 2 2 2 2
Capacity steps 4 4 4 4 4 4
Minimum capacity (%) 20/30 25 22/29 19/32 17/33 17/33
Refrigerant Charge (3)
Circuit A (kg) 21 24 29 30 37 41
Circuit B (kg) 21 24 29 30 37 41
(1) at Eurovent Conditions (Cooling: Water 12°C/7°C - Air. 35°C / Heating: Water 40°C/45°C - Air. DB7°C / WB6°C)
(2) per motor
(3) per circuit
(4) Max rated conditions.
(5) Dual Pump Option
(6) For units with HESP option, contact your local sales office

14 CG-SVX04C-E4
Table 5 - Hydraulic module and buffer tank
EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP
EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP
060 080 100 120 125 130 160 180 210 240 260
Motor (2) (kW) 2.2 2.2 2.2 4.0 2.2 4.0 4.0 4.0 4.0 5.5 5.5
Rated Amps (2) (A) 4.9 4.9 4.9 4.9 7.5 7.5 7.5 7.5 7.5 11.1 11.1
Motor RPM (rpm) 2900
Water strainer Ø 2" 2 1/2" 2
1/2" 2 1/2" 2 1/2" 2 1/2"2 1/2" 3" 3" 3" 3"
Expansion tank volume (L) 25 25 25 25 25 35 35 35 35 35 35
User volume expansion
capacity (1) (L) 1000 1000 1000 1000 1 000 1400 1400 1400 1400 1400 1400
Antifreeze heater (W) 150
Piping material Steel
Hydraulic Module Weight (kg) 103 108 108 108 108 110 110 114 114 189 189
Water tank volume
(Option) (L) 370 410 410 410 410 570 570 570 570 570 570
Water tank additionnal
shipping height (mm) 400
Water tank additionnal
shipping weight (kg) 396 437 436 436 436 644 644 644 644 644 644
(1) Hydrostatic pressure 3 bar at 45°C with -12°C mini
(2) Dual Pump Option
General Data

General unit characteristics
For minimum clearance, consult the
certified submittals, which are
available on request from your
Daikin sales office.
Unit nameplate
The unit nameplate gives the
complete model reference numbers.
The unit power rating is shown, and
power supplies should not deviate
by more than 5 % from the rated
power.
Compressor motor amperage is
shown in box I.MAX.
The customer's electrical installation
must be able to withstand this current.
Installation instructions
Foundations
No special foundations are required,
provided the supporting surface is
flat and level, and can withstand the
weight or the unit.
Isolating rubber pads
They are supplied as standard with
the machine, and should be placed
between the supporting floor and
the unit to isolate from the ground.
- 4 pads for size 060 unit without
buffer tank
- 6 pads for sizes 075-260 units
without buffer tank
- 8 pads for all sizes of units with
buffer tank
- The manufacturer does not
recommend to install spring
isolators.
Water drain hole
For units with an hydraulic module,
condensates are to be collected
below the pump and drained away.
Clearance
Respect recommended clearance
around the unit to allow maintenance
operation to take place without
obstruction and recommended
clearance around condenser.
Caution
Unit operation is function of the air
temperature. Any recycling of the air
fed out by the fans will increase the
air intake temperature over the
condenser fins and can result in high
pressure cut-out.
In this case the standard operating
conditions and performance are
modified.
Operation of the unit may be
affected by an increase in air
temperature on the condenser. When
the units are positioned in a windy
area, avoid all the risks of air-cooled
recycling. Refer to certified
drawings.
Figure 1 - Handling - units without
Buffer tank
Note:The plates welded at the end of the bases
must not be used for handling.
Figure 2 - Handling - units with
buffer tank
CG-SVX04C-E4 15
Installation

16 CG-SVX04C-E4
Table 6 - Dimensions of recommended slings and swing-bar :
EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP
EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP
060 080 100 120 125 130 160 180 210 240 260
Without buffer tank
A (mm) 1400 1400 1400 1400 1400 2400 2400 2400 2400 2400 2400
B (mm) 2300 2300 2500 2500 2500 3100 3100 3100 3100 3100 3100
With buffer tank
A (mm) 1400 1400 1400 1400 1400 2400 2400 2400 2400 2400 2400
B (mm) 2700 2800 3100 3100 3100 3400 3400 3400 3400 3400 3400
Table 7 - Shipping weights
EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP
EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP
060 080 100 120 125 130 160 180 210 240 260
Without hydraulic module
EWAP (kg) 834 954 1124 1260 1284 1588 1778 2030 2181 2344 2377
EWYP (kg) 864 996 1136 1272 1296 1650 1860 2114 2271 2434 2467
Additional weight for single pump hydraulic module
EWAP (kg) 29 34 34 64 64 66 66 70 70 84 84
EWYP (kg)
Additional weight for double pump hydraulic module
EWAP (kg) 103 108 108 108 108 110 110 114 114 189 189
EWYP (kg)
Additional weight for buffer tank
EWAP (kg) 396 437 436 436 436 644 644 644 644 644 644
EWYP (kg)
Installation

Before making any connections,
make sure the labeling for entering
and leaving water corresponds to
the submittals.
Units are available in 3 versions:
Without hydraulic module (with or
without contactors)
With hydraulic module (single or
dual pump)
With hydraulic module and buffer
tank.
Typical water circuits are given in
figures 3 to 5
Figure 3 - Unit without hydraulic
module - typical water circuit
Figure 4 - Unit with hydraulic
module - typical water circuit
1
2
3
5
7
8
1
1
0
12
2
6
4
14
1
3
9
11
1
1
1
14
9
4
13
12
1
Figure 5 - Unit with hydraulic
module and buffer tank - typical
water circuit
Legend for figures 3 to 5
1. Pressure port for water gauge
2. Shut off ball valve
3. Water strainer
4. Evaporator
5. Expansion tank
6. Relief valve
7. Pump (single or dual)
8. Removable water gauge
9. Flow control
10. Filling and drain valve
11. Balancing valve
12. Freeze protection
13. Leaving water temperature sensor
14. Return water temperature sensor
15. Buffer tank
Warning: Units with hydraulic
module and buffer tank content all
safety and operation devices and
only require the supply and return
piping to be connected using
expansion compensators.
Units without hydraulic module have
to be connected according to figure 6.
Figure 6 - Unit without hydraulic
module and buffer tank - typical
water circuit
1
2
3
5
7
8
1
9
1
0
12
2
1
5
6
4
4
14
4
4
13
3
3
11
1
1
Figure 7 - Unit with hydraulic
module and buffer tank - typical
water circuit
1 Pressure gauges: show entering
and leaving water pressure
(2 pressure ports are available
inside of the unit - see item 1 in
figure 5)
2 Balancing valve: adjusts water flow.
3 Air purge allows to remove the air
from the water circuit during fill up.
4 Stop valves: isolate chillers and
water circuiting pump during
maintenance operations.
5 Thermometers: indicate chilled
water entering and leaving
temperatures.
6 Expansion compensators: avoid
mechanical stress between chiller
and piping installation.
7 Stop valve located on the outlet
connection: used to measure the
water pressure inlet or outlet of
evaporator.
8 Strainer: avoid to get heat
exchangers dirty. All installation
must be equipped with efficient
strainer in order that only clean
water enters into exchanger. If
there is no strainer, reserve will be
formulated by the technician at the
start-up of the unit.
The strainer used must be able to
stop all particles with a diameter
greater than 0.8 mm.
9 Draining: used as the draining the
plate heat exchanger.
To protect the environment, it is
compulsory to recover and process
glycol brines.
CG-SVX04C-E4 17
Installation

18 CG-SVX04C-E4
Minimal installation water
content
The water volume is an important
parameter because it allows a stable
chilled water temperature and avoids
short cycle operation of the
compressors.
Parameters which influence the
water temperature stability
- Water loop volume.
- Load fluctuation.
- Number of capacity steps.
- Compressors rotation.
- Dead band.
- Minimum time between 2 starts of
a compressor.
Minimum water volume for a
comfort application
For comfort application we can allow
water temperature fluctuation at part
load.The parameter to take into
account is the minimum operating
time of the compressor. In order to
avoid lubrication problem on a scroll
or an hermetic reciprocating
compressor it must run at least
2 minutes (120 seconds) before it
stops.
The minimum volume can be
determined by using the following
formula
Volume = Cooling capacity x Time x
highest capacity step (%) / Specific
heat / Dead band
Minimum operating time
= 120 seconds
Specific heat = 4.18 kJ / kg
Dead band recommended = 3°C
Dead band calculation
Dead band = (Biggest compressors
step tonnage /Total tonnage)
X (Water temperature difference
entry/leaving) + allowed water loop
temperature fall
Minimum allowed temperature fall
= 1.5°C
Minimum dead band calculation
table versus the targeted water
temperature deltaT
It is preferable to have a higher dead
band than the minimum
recommended.
Installation
456 1.5 456
060 15 25 2.4 3.0 3.6 1.5 3.9 4.5 5.1
080 15 30 2.0 2.5 3.0 1.5 3.5 4.0 4.5
100 25 40 2.5 3.1 3.8 1.5 4.0 4.6 5.3
120 25 45 2.2 2.8 3.3 1.5 3.7 4.3 4.8
125 25 50 2.0 2.5 3.0 1.5 3.5 4.0 4.5
130 15 50 1.2 1.5 1.8 1.5 2.7 3.0 3.3
160 15 60 1.0 1.3 1.5 1.5 2.5 2.8 3.0
180 20 70 1.1 1.4 1.7 1.5 2.6 2.9 3.2
210 25 80 1.3 1.6 1.9 1.5 2.8 3.1 3.4
240 30 90 1.3 1.7 2.0 1.5 2.8 3.2 3.5
260 25 100 1.0 1.3 1.5 1.5 2.5 2.8 3.0
Unit
size
Bigger
Compressor
tonnage
step
Total unit
Tonnage
Compressor step
temperature fall
versus DeltaT water
loop
Minimum
recommended
water loop
temperature
fall
Dead Band
minimum versus
delta T water
loop

Table 8 - Minimum water loop volume for comfort application
EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP EWAP
EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP EWYP
060 080 100 120 125 130 160 180 210 240 260
Water volume (l) 360 360 610 640 620 370 370 500 650 760 630
At Eurovent conditions
CG-SVX04C-E4 19
Installation
Minimum water volume for a
process application or for a chiller
which has to run with low ambient
temperature option.
For Process application we have to
minimize the water temperature
fluctuation at part load. In order to
avoid problem on a scroll or a
hermetic reciprocating compressor it
must run at least 2 minutes
(120 seconds) before it stops and the
minimum time between two starts is
5 minutes (300 seconds).
The water volume has to be able to
provide the cooling capacity while
the unit is shut down.
The minimum volume can be
determined by using the following
formula
Volume = Cooling capacity x Time
x highest capacity step (%) / Specific
heat / Dead band
With these values the formula
becomes
Volume = Cooling capacity
X 9.56 x highest capacity step (%)
For the EWAP running in following
conditions: Air temperature 35°C,
water 12/7°C, this gives the following
volumes. If the total water volume of
the installation is below the above
mentioned values it is necessary to
use a buffer tank.
Minimum time = 180 seconds
(300-120)
Specific heat =4.18 kJ / kg
Dead band recommended =
Function of the process
With these values the formula
becomes:
Volume = Cooling capacity x 43
x highest capacity step (%) / Dead
band
Increasing the dead band is like
adding water volume to the loop.

20 CG-SVX04C-E4
Water treatment
Untreated or insufficiently treated
water, if used in this unit, may cause
scale, slime or algae to accumulate
or cause erosion and corrosion.
As Daikin does not know the
components used in the hydraulic
network and the quality of the water
used, we recommend the services of
a qualified water treatment
specialist.
The following materials are used in
Daikin chillers heat exchangers:
- Stainless steel plates AISI 316,
1.4401 with copper brazing.
- Water piping: steel
- Water connections: brass
Daikin will not accept any ability in
regards of damage due to the use of
untreated or improperly treated
water or from the use of saline or
brackish water.
If required, contact your local Daikin
sales office.
Winter freeze protection
During negative ambient air
temperature chilled water piping
must be fully insulated.
Ensure that all safeties are taken to
prevent frost damage during
negative ambient air temperature.
Following system can be used:
- Electrical heater mounted on all
water piping exposed to negative
temperatures.
- Start chilled water pump during
negative ambient air temperature.
- Add ethylene glycol in the chilled
water.
- Drain water-circuit, however be
aware of corrosion process when
drained.
Electrical connections
Caution:
1.The greatest care should be taken
when cutting through passages
and installing electric wiring.
Under no circumstances should
chips of metal or cuttings of
copper or isolating material fall
into the starter panel or electric
components. Relays, contactors,
terminals and control wiring
should be covered and protected
before power supplies are
connected.
2. Install power supply cabling as
shown in wiring diagram.
Adequate cable gland should be
chosen, ensuring no foreign
bodies enter the electrical housing
or components.
Caution:
1. Cabling must comply with
standards in force.The type and
location of fuses must also comply
with standards. As a safety
measure, fuses should be visibly
installed, close to the unit.
2. Only copper wiring should be
used. Using aluminium wires can
produce galvanic corrosion and
possibly lead to superheat and
failure of connection points.
% Ethylene glycol
Brine temperature (°C)
Installation
Figure 8 - Freezing point versus ethylene
glycol percentage
1. Liquid
2. Freezing without burst effect
3. Freezing with burst effect
Expansion valves settings
In order to keep the compressor in
the operating envelope, it is
mandatory to control the superheat
suction at commissioning. It shall
reduce the compressor discharge
gas temp and increase the saturated
suction temperature, increasing by
the way the unit capacity. The rule to
reduce the suction superheat is to
loosen the expansion valve
adjustment screw. One turn
counterclockwise equals to -1°C to
-2°C superheat decrease. It is
recommended to lower the
superheat by increasing the suction
pressure by making adjustments to
the expansion valve setting prior to
attempting to lower the LP setting
parameter to avoid unit tripping on
low pressure. Make sure there is
enough subcooling.This can be
convenient for units with Ethylene
Glycol and Propylene Glycol.