Daintree WWD2-2IW User manual

DT041
WWD2-2IW
Daintree® Wireless Controls
Wireless Wall Dimmer
Product Overview
The Daintree® Wireless Wall Dimmer is a battery-powered wall switch for use in a Daintree Networked or Daintree EZ
Connect application. The WWD2-2IW device installs into an existing junction box to replace the existing wall-mounted
switch with a wireless solution that enables dimming and on/off commands to be delivered to the luminaires in its
commissioned space. The communication with the Daintree system utilizes a secure and reliable wireless connection
which helps minimize installation costs and complexity.
RISK OF ELECTRIC SHOCK
• Disconnect power before servicing or installing product.
WARNING
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Save these instructions for future use.
IMPORTANT
To ensure the product warranty is valid, please ensure
all installation instructions and environmental conditions
for storage and operation are complied with.
Installation to be performed by factory trained or qualified
personnel.
Save These Instructions
Use only in the manner intneded by the manufacturer.
If you have any questions, contact the manufacturer.
Prepare Electrical Wiring
Electrical Requirements
• When replacing a line voltage switch, the
power must be off at the branch circuit
breaker. Bypass the line voltage switch to
provide uninterrupted power to the fixtures
and make sure the connection is properly
insulated before installing the wireless switch.

Installation of Back Housing onto Junction Box
Installation Guide
2
123
45
Disconnect power to
the junction box
Remove the junction box
cover plate
Reconnect wires (previously
connected to wall switch)
with wire nuts.
For proper installation into
a dualgang junction box, the
tabsbetween adjacent back
housings must be removed.
Carefully observe the correct
orientation (the UP arrow
should be in the upper right
corner on each backhousing).
After double checking the
product orientation, breakoff
the necessary tabsusing pliers.
Uninstall existing wall
switches from the junction
box.
Daintree® Wireless Controls
Wireless Wall Dimmer (WWD2-2IW)
DOUBLE CHECK PRODUCT ORIENTATION BEFORE BREAKING OFF TABS.
The wall dimmer will only install into the back housing in one orientation.
Break off tabs only after the correct product orientation has been confirmed.
6Install the back housing(s)
of the wall dimmer(s) into
the wall box.

Installation Guide
3
Installation of Device into Back Housing
Insert the back housing piece
into the junction box and
secure with two screws.
To reset the networkof the device,
remove the faceplate fromthe
device. Then press and hold the
reset button for 5 seconds. Install
the faceplate backonto the device.
Press either dimming up or down
button to enter the pairing mode
to join the device to a network.
Separate the battery cover
from the device. Pull the two
plastic insulation strips out
of the battery compartment.
Put the battery cover back
on the device.
Network Reset
123
Install the main body of the
device into the back housing.
Install the faceplate onto the
device. Note: Device supports
the use of other standard
faceplates on the market.
45
Use a standard screwdriver
to remove the devices from
the back housing
Daintree® Wireless Controls
Wireless Wall Dimmer (WWD2-2IW)

Battery Replacement
Installation Guide
4
Product Dimensions
123
45
The device’s LED flashing
on for 2 seconds every 30
seconds indicates that the
batteries need to be
replaced.
Remove the device from
the back housing.
Install the main body of
the device into the back
housing.
Install the faceplate onto
the device. The device
will rejoin its network
automatically.
Separate the battery cover
from the device. Replace
the batteries with AAA
batteries. All batteries need
to be replaced at the same
time.
Daintree® Wireless Controls
Wireless Wall Dimmer (WWD2-2IW)

Installation Guide
5
Product Operation
Button Functionality
LED Indicator
Daintree® Wireless Controls
Wireless Wall Dimmer (WWD2-2IW)
Up Button
Short press
Double short press
Hold
Down Button
Short press
Double short press
Hold
Lights ON at previous level
Lights ON at 100% output
Turn ON and dim up
Lights OFF
Lights ON at minimum dimming level
Turn ON and dim down or dim down if lights are already ON
Rapid flash (12 times per second)
for up to 30 seconds
Solid ON for 10 seconds
Flashes once (100ms duration)
Flashes ON 2 seconds every
30 seconds
Device is trying to join a ZigBee network
Device successfully joined a ZigBee network
Device has been activated while in the network
Batteries need to be replaced

Installation Guide
6
Technical Data
SKU DESCRIPTION ARTICLE NO
Operating Control
E486320
93141337 Daintree Wireless Controls Wall Dimmer, In Wall, 2 Button, Battery WWD2-2IW
Product Specifications
Product Certifications
Product Availablity
Daintree® Wireless Controls
Wireless Wall Dimmer (WWD2-2IW)
Dimensions
Weight
Power Supply
Battery Life
Operating Environment
Status Indicator
Mounting
Warranty
Purpose of Control
Construction of Control
Type 1 Action
Pollution Degree 2
114mm H x 70mm W x 36mm D
130g
(4) AAA 1.5V battery
5 years (normal operation)
-10°C to 40°C (Indoor Use Only)
Network join status, button triggered
Mounts into junction box
5 years
Operating Control
Independently Mounted
FCC ID: 2AS3F-WWD2IW
IC: 25008-WWD2IW
The alkaline batteries supplied with your wireless switch are prone to leak over their lifetime, particularly when the battery is mostly
depleted. In the event that your battery leaks alkaline into the battery compartment, the chemicals can damage the metal terminals.
The chances of this happening can be reduced by changing the batteries in the switch promptly when the batteries are nearing their
end of their useful life. If a battery leak should occur, however, it should be cleaned up to prevent damage to the wireless switch.
WARNING: THE CHEMICALS LEAKED FROM ALKALINE BATTERIES ARE CORROSIVE. WHEN HANDLING LEAKING BATTERIES, PROPER
PERSONAL SAFETY EQUIPMENT SHOULD BE USED, INCLUDING RUBBER GLOVES AND EYE PROTECTION.

If it is discovered that the batteries have leaked, wearing rubber gloves and using eye protection, remove all of the batteries from the
battery compartment and seal them in a plastic bag. The bag should be discarded in a manner in accordance with local laws and
regulations. Then, using a small cloth lightly moistened with vinegar or other mild acid, carefully wipe all of the leaked battery
chemicals from inside the battery compartment and allow it to dry. Once dry, the batteries may be replaced and the switch may be
reinstalled.

FCC RF Exposure Statement: Specific Absorption Rate (SAR) is a measure of the rate of RF (radiofrequency) energy
absorption by the body from the source being measured. This equipment has been found to be exempt from the RF
Exposure SAR Evaluation when the device is installed such that a person's head will, in normal conditions, be 10mm
away from the transmitter and antenna of the device.
www.gecurrent.com
© 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without
notice. All values are design or typical values when measured under laboratory conditions.
DT041-Daintree-WWD2-2IW-Wall-Dimmer-Installation-Guide
Installation Guide
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help
Supplier’s Address (USA): Cleveland, Ohio
Supplier’s Phone: [phone]
Supplier’s Name: Current Lighting Solutions, LLC
Product Name: Wireless Wall Dimmer
Model No: WWD2-2IW
Supplier’s Website: www.gecurrent.com
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
Daintree® Wireless Controls
Wireless Wall Dimmer (WWD2-2IW)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences
et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.