Dakota Alert SBB-4000 User manual

Dakota Alert
WIRELESS SECURITY EQUIPMENT
Solar Break Beam
Transmitter
SBB-4000
USER GUIDE

PACKAGE CONTENTS:
AB
BACK OF
BEAMS
TOOLS NEEDED:
• Philips Screwdriver
• 7mm Wrench or an Adjustable Wrench
• Break Beam Pair “A” and “B” (2 sensors)
• (8) M4x10 Pan Head Screws with
Flat Washers and Lock Washer
• (8) M4x40 Pan Head Screws
• (8) M4 Nut
• (4) Metal Pipe Mounts
• (4) Pipe Mount Rubber Adapters
• (2) “C” Mounting Brackets
• User Guide
X 8
X 2
M4x10 Pan Head Screws with
Flat Washers and Lock Washers
M4x40 Pan Head Screws
with Nuts
X 8
X 4
X 4
Metal Pipe Mounts
Pipe Mount
Rubber Adapters
“C” Mounting Brackets
NOTE: Remove the protective plastic
covering the lenses and solar panels

PAIRING THE SENSORS:
NOTE: It is recommended to charge both the “A” and “B” unit via a
USB Micro charger (not included) for about 4-6 hours
before starting the initial set-up.
1. Before mounting the sensors in a permanent location, start by placing
them on a table or other at surface about 6 to 12 inches apart with
the three IR lenses pointing towards each other.
2. Press and release the power button on the “B” sensor. The LED will
start ashing.
3. Press and release the power button on the “A” sensor and the LED will
start ashing green.
4. When the LED stops ashing on the “A” sensor, the pairing is complete
(about 30 seconds).
5. Test the pairing by completely blocking the beams. A piece of
carboard can be used or physically move the beams so they are not
aligned. The LED on the “A” sensor will ash for about two seconds.
USB
Charging Port
BACK FRONT
IR LENSES
LED Light
Power
Button
Rubber
Plug
Be sure to re-insert rubber plug
before mounting permanently

CODING THE RECEIVER:
1. The SBB-4000 can send a signal to any of the Dakota Alert
4000 series receivers.
2. Please refer to your receiver manual for coding instructions of
your particular receiver.
3. To activate the SBB-4000 to send a signal to your receiver, either break the
beams while they are paired or quickly press and release the power button
on the “A” sensor. A signal will be sent to the receiver for code learning.
4. If coding more than one set of beams to a receiver, repeat steps 2 and 3 for
each additional pair of beams.
SETTING REMINDER SIGNAL FOR CONTINUOUSLY
INTERRUPTED BEAMS:
1. If the beams are continuously interrupted, the “A” sensor will send a
reminder signal to the receiver. The factory default is to send a signal
every 20 seconds if the beams are continuously interrupted.
2. To change the reminder duration to 5 minutes, press and hold the power
button of the “A” sensor for 5 seconds then release. The LED will
start ashing red.
3. To change back to the 20 second reminder duration, press and hold the
power button of the “A” sensor for 5 seconds then release. The LED will
now ash green.
4. After you are nished pairing, coding, and setting the reminder time,
insert the rubber plugs into the holes near the power button on both the
“A” and “B” side. To ensure that water does not enter the beams during
outdoor use.
Power Button of
“A” Unit
Be sure to re-insert rubber plug
before mounting permanently

MOUNTING THE SENSORS:
Before mounting, choose a suitable location:
• The recommended mounting height is about 3 feet. This will help to
avoid false alerts from small animals crossing under the beams.
• The sensors can be mounted up to 300 feet apart facing each other.
• Mount the sensor on a solid object such as a wall, post, or pipe.
Mounting to a at surface
• Use appropriate screws or fasteners (not included) to mount the back of
the “C” bracket directly to a at surface such as a wall or wood post.
Mounting to a pole or pipe
• Use the provided screws (M4x40 Pan Head Screw and Nut), pipe mount
and rubber adapter to connect the “C” bracket to the pipe.
Side View of
Pipe Mount
Sensors should be facing
each other at approximately
the same height
CORRECT ALIGNMENT INCORRECT ALIGNMENT
Top View of
Pipe Mount
M4x40
PAN HEAD
SCREW
PIPE MOUNT
RUBBER ADAPTER
METAL
PIPE MOUNT
M4 NUT
PIPE

1. Make sure both the “A” and “B” units are powered on and the rubber plugs
are inserted into the power button recess.
2. Use the provided small screws, split ring lock washers and at washers to
mount the “A” and “B” beams to the “C” brackets.
3. Align the “A” and “B” units so the lenses are pointing towards each
other.
4. The beams can be rotated inside the “C” bracket by loosening the screws on
the top and bottom of the sensor to help achieve alignment. After rotating
the sensors re-tighten the screws.
5. If the beams are paired, you will get a signal when you walk between the
beams. If you get a signal every 20 seconds (5 minutes optional), this is the
reminder signal and the beams are not aligned. Slightly reposition the
beams until the reminder stops and the beams are activated by walking
between them.
MOUNTING SENSORS TO THE “C” BRACKET:
M4x10 Screw
Lock Washer
Flat Washer
Loosen Screw To
Rotate Sensor
M4x10 Screw
Lock Washer
Flat Washer
WHEN MOUNTED, THE LEVEL BUBBLE MUST
BE TOWARDS THE TOP
2 screws
2 screws
Mount with
Bubble on Top

The beams will charge automatically outdoors with the built-in solar panels. If
the beams are used in an interior location with no light, they can be manually
charged.
1. For interior locations, remove the rubber plug from the power button.
2. Locate the USB Micro charging port.
3. Connect a USB Micro charger (not included) to the port.
4. Once nished charging insert the rubber plug back into the recess.
NOTE: You can either leave the charger connected indenitely or you can fully
charge the beams periodically. When the beams are fully charged the built-in
batteries will usually hold a charge for about a month, depending on
activations.
RECHARGING THE BEAMS:
Charging Port
(Under Rubber Plug)
Be sure to re-insert rubber plug
before mounting permanently
USB
Charging Port

If you are getting false signals:
• Make sure there are no tree branches or other obstructions that may be
periodically blocking the beams.
• If the signal is occurring every 20 seconds (5 minutes), this indicates that
the beams are either misaligned or there is something continuously
blocking the beams.
• You may receive false signals during extreme rain, snow, or fog.
• If the false signals are occuring every 20 seconds (5 minutes) the battery
may be dead in the B unit. Manually charge the B unit via USB micro for
several hours, then turn on the B unit by pressing the power button.
If you are getting no signals:
• Make sure both the A and B units are powered on.
• Make sure the beams are coded to your receiver.
• Make sure the beams are charged. You may need to manually charge with
a USB Micro charger.
• Move the beams closer to your receiver.
• Keep the A sensor away from large metal objects that may interfere with
the radio signal.
Specications:
• Power source: 18650 rechargeable lithium battery, solar charger or USB
Micro (not included).
• Frequency: 433.92 MHz
• Wireless range: up to 1 mile*
• Maximum detection range: Up to 300 feet.*
• Operating temperature: -20 to 120F.
*Actual range will vary depending on local terrain and obstructions.
Tech Support:
If you have any troubles using this product after reading the manual, please
contact us. You can reach us by phone at 605-356-2772 from 8:30 Am to 5:00
PM Monday through Friday (Central Standard Time). We will be happy to
answer any questions and help in any way we can.
TROUBLE SHOOTING:
Safety information:
• Only use this product for the detection of moving objects such as people
or vehicles.
• Do not disassemble or attempt to repair the product.
• Do not install this unit with any other infrared detectors as this may cause
false signals.
• Do clean and inspect the beams regularly for proper use. If any trouble is
found, please contact Dakota Alert, Inc.

Warranty:
Dakota Alert warrants this product to be free of defects in materials and
workmanship for a period of one year from the date of purchase. This warranty
does not cover damage resulting from accident, abuse, act of God, or improper
operation. If this product does become defective, simply return it to Dakota
Alert. Please include a note describing the troubles along with your name and
return address as well as the original sales receipt. If the product is covered
under the warranty it will be repaired or replaced at no charge. If it is not
covered by the warranty, you will be notied of any charges before work is done
Legal Notices:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Cancer and Reproductive Harm. Go to
www.P65Warnings.ca.gov for more information

SBB 4000 WORKS WITH OTHER
DAKOTA ALERT 4000 SERIES PRODUCTS
DCR 4000 Receiver (no relays)
The DCR-4000 is a receiver that will work with any
Dakota Alert 4000 transmitter. This receiver has 12
different chimes/tunes available so each transmitter can
be distinguished by the sound you hear. An extra receiv-
er can be placed in an out building or on a different oor
of your home.
RE-4k+ Receiver (2 relay outputs and one 12 VDC output)
The RE-4k Plus is a receiver that will work with any
Dakota Alert 4000 Series wireless transmitter. The receiver
is simple to program and can take signals from up to 16
different transmitters. There are 16 different chimes/tunes
available so each transmitter can be distinguished by the
sound you hear. The receiver also has two form C relay
outputs as well as one 12 VDC output. The outputs can be
selected for 1, 5, 15 seconds or 5 minutes. Each sensor can
be set to independently select the output(s), time duration,
sound and ashing LED. An extra receiver can be placed in
an out building or on a different oor of your home.
PR-4000 Portable Receiver
The PR-4000 receiver is compatible with all Dakota Alert
4000 series transmitters. It can receive and store alert
signals from up to 16 different 4000 series transmitters.
When a signal is received, the zone will be displayed on the
LCD screen. The PR-4000 can be set to give an audible tone
or silent vibrate alert. It can store up to 200 event logs for
each of the zones with a time and date stamp. The portable
receiver is powered by a rechargeable Li-Ion battery which
can hold a charge for up to a week.

DCMT 4000 Transmitter
The DCMT-4000 motion detecting sensor
operates on one 9-volt battery (not included)
and detects a person or vehicle passing by out
to about 100 feet.
UT 4000 Transmitter
The UT-4000 operates on a 3-Volt lithium battery
(included) and has several different methods of
activation. The UT-4000 has a push button that can
be used as a panic button or a wireless doorbell.
There is also a magnetic door/window contact and
terminals for either a normally open (N/O) or a
normally closed (N/C) input. These inputs can be
used with any sensor contacts.
DCPT 4000 Transmitter
The DCPT-4000 transmitter operates on three
CR-123A batteries (included) and has 50 feet
of direct burial wire connecting the probe to the
exterior case. The probe is buried parallel to the
driveway. It detects vehicles passing by within
approximately 10-12 feet.
DCRH 4000 Transmitter
The DCHT 4000 transmitter operates on one
9-volt battery (not included) and has 25’ of 3/8”
diameter exterior hose that lies across the drive.
When a vehicle drives over the hose, a signal is
sent to the receiver up to about one mile* away.

Dakota Alert, Inc.
www.dakotaalert.com
Phone: [phone]
Fax: [phone]
Address: 32556 477th Ave. | P0 Box 130 | Elk Point, SD 57025