Dakota 6723F Manual

Commissioning
Fitting/replacing bulbs
Instruction leaflet
Dakota LED Outdoor Brick
6723F
For your safety, always switch off the supply before cleaning and maintaining.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
Do not use solvents or abrasive cleaners as these could damage the finish.
Do not clean the units with a pressure washer.
The shade must be replaced immediately should the shade become cracked or damaged. This
fitting must not be used without the shade in place.
• Gently push the product into the wall, taking care not to trap any wiring.
• Replace fuse or circuit breaker and switch on. Your light is now ready for use.
• The LED's in this product are non-replaceable.
Care and cleaning
Light
Check that...
• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection block.
26/05/2017

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This product is Double Insulated and does not require connection to an Earth circuit.
Please read these instructions carefully before commencing any work. It is recommended that this fitting is
installed by a qualified electrician.
Install in accordance with the IEE Wiring regulations and the Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons
cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified
electrician.
This light fitting should be connected to a 5 amp fused circuit.
If replacing an existing fitting, make a note of the connections.
This product is not suitable for dimming.
This product contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
This product is rated at IP65
This product is not suitable for location in or near a marine environment.
Specification
Voltage: 240V 50Hz a.c.
Lamp: 3W LED Module - Blue/30lm
IP rating: 65
Layout
Installation
• Remove the terminal box cover and set aside for refitting later. Having identified the wiring from your existing
fitting, connect to the terminals as shown below:
• Fit the cover in place and refit the screws. Adjust the cable to suit and tighten the gland to maintain the IP rating
of the product.
Wiring
• Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the
junction box and the light fitting.
• Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction
boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
• We recommend that you use H05RN-F specification cable (not supplied) which is an outdoor grade, rubber
heathed cable. The mains supply cable must have a minimum cross sectional area of 1.0mm².
• Cables must be protected using suitable conduit or plastic trunking.
Existing fittings must be completely removed before installation of a new product. Before removing the existing
fitting, carefully note the position of each set of wires.
• The product comes with a housing unit that must be fitted into the hole prior to any wiring taking place.
• Cut the mounting hole for the unit taking care not to damage any pipes or mains cables beneath the
mounting surface.
Cutout Void Depth
184mm x 62mm 60mm
• Fit the housing into position and secure. This surround may be cemented in position. Wait until the cement
has set before continuing with the installation.
Switch off the power supply
at the consumer unit.
Insert and secure the Brick
Light outer casing.
Fix in place the clear lens and
metal outer frame using the
screws provided.
Switch on the power supply at
the main fuse box and test
fitting.
NEUTRAL
LIVE
BLUE (N)
BROWN (L)
SUPPLY LIGHT FITTING