danalock V3 BT HK SCANDI User manual

Simple Guidelines
Please follow these guidelines when conguring, using or
recycling the Danalock V3. Violating these guidelines may be
dangerous, illegal or otherwise detrimental. Further detailed
information is provided in this manual.
Terms of use
The Danalock Danalock V3 is designed for indoor use only. Use
only Danalock approved accessories for the Danalock V3. Do
not connect incompatible products, and do not operate the
Danalock V3 where wireless radio communication is prohibited.
Like hospitals, buildings near blasting sites etc.
Do Not Operate Where Prohibited
Do not allow the Danalock V3 unit to operate wherever wireless
radio communication use is prohibited or when doing so may
cause interference or danger as the Danalock V3 cannot be
turned o after installation.
Device Operation and human exposure to
electromagnetic elds
The Danalock V3 unit is a low power radio transmitter and
receiver. Periodically the Danalock V3 wakes up either due to
activity or by a timer. When it is ON, it receives and sends out
radio frequency (RF) signals for a short period of time.
Specic Human Absorption Ratio (SAR)
The Danalock V3 unit is not intended for handheld use or to be
worn on the body. A minimum separation of eight (8”) inches
(20 cm) is to be maintained between the Danalock V3 and any
persons’ body.
Pacemakers and other Medical Devices
If any other personal medical devices are used in the vicinity of
a Danalock V3 unit, consult the manufacturers of the medical
devices to determine if they are adequately shielded from
external RF energy. Physicians may be able to assist in obtaining
this information.
Interference
Like all wireless devices, the Danalock V3 may encounter
electrical interference that may aect its performance. The
Danalock V3 is tested and certied according to international
and European standards. The performance hereof ensures
correct operation in the presence of electromagnetic
interference and/or electrostatic discharge.
Category of use
The Danalock V3 is an electronic doorknob with wireless
interface for mounting on access doors.
Security for electrical functions
The Danalock V3 has an indoor led indications for operational
status but no sound alarms in case of a connected lock
malfunction.
Security for electrical manipulation
The Danalock V3 is tested compliance to the EMC requirement
laid out in the 2014/53/EU directive. The performance hereof
ensures correct operation in the presence of electromagnetic
interference and/or electrostatic discharge.
Children
The Danalock V3 series and its accessories are not used to solicit
data from or market to children
Fire doors
The Danalock is not approved for use with re doors.
Water-Resistance
The Danalock is not water-resistant. The lock must therefore
be installed on the inside of the door where it is dry and not
subjected to either water streams or submersion. EN 14846
corrosion resistance classication grade=0.
Accessories and Batteries
The Danalock uses 4 x Panasonic CR123A or Duracell DL123A
lithium batteries (Intl. model: CR17345). Use only approved
accessories or batteries. Do not connect incompatible products.
There is risk of explosion or re if an incorrect type replacement
battery contacts are shorted. Do not exceed the temperature
ranges or other environmental conditions specied by the
battery manufacturer. Dispose of used batteries according to
the instructions provided with the batteries.
Potentially Explosive Atmospheres
The Danalock cannot be turned o after installation, so any
building installed with Danalock etc. must not be located in an
area with a potentially explosive atmosphere and obey all signs
and instructions not to use Danalock in such areas. Sparks in

such areas could cause an explosion or re resulting in bodily
injury or even death.
Areas with a potentially explosive atmosphere are often, but not
always marked clearly. Potential areas may include: fueling areas
(such as gasoline stations); below deck on boats; fuel or chemical
transfer or storage facilities; areas using liqueed petroleum
gas (such as propane or butane); areas where the air contains
chemicals or particles (such as grain, dust, or metal powders);
and any other area where it would normally be advisable not to
install the Danalock.
Battery Safety Information
Adhere to the following guidelines to avoid the risk of re or
explosion:
1 Dispose of the used battery according to the instructions
provided with the battery.
2 Do not drop, puncture, disassemble, mutilate, or incinerate
the battery.
3 Touching both terminals of a battery with a metal object will
short circuit the battery. Do not carry batteries loosely if the
contacts may touch coins, keys, and other metal objects
(such as in pockets or bags).
4 Do not stack batteries taken out of the carry case.
5 Do not heat the batteries to try to rejuvenate their charge.
6 Do not exceed the temperature ranges or other
environmental conditions specied by the battery
manufacturer.
7 Never use the Danalock without the battery cover installed.
8 Do not mix batteries from dierent vendors.
9 Do not mix new and used batteries in the lock.
Disclaimer
It is very important to replace all 4 batteries at the same
time. Please use only standard CR123 lithium batteries. Not
replacing all batteries at the same time can aect the batteries
to heat and potentially cause them to explode. Danalock has
no responsibility in any way if the replacement of batteries is
done inaccurately.
Disposal of Waste Batteries
(Applicable in the European Union only)
The symbol (crossed out wheeled-bin) on your battery
indicates that the battery shall not be disposed with other
unsorted waste, but shall be collected separately and handed
over to your local community waste collection point or other
available collection points for the recycling, at the end of its use.
If a chemical symbol is printed under the symbol it indicates that
chemical substances (Hg = mercury, Cd = cadmium or Pb = lead)
are contained in the battery.
Inappropriate waste handling could possibly have a negative
eect on the environment and human health due to potential
hazardous substances. With your cooperation in the correct
disposal of this battery, you contribute to reuse, recycle and
recover the batteries and our environment will be protected.
For more information, please contact the Government Waste-
Disposal department in your country or the shop where the
battery was purchased.
Disposal of Waste Electrical & Electronic
Equipment of products for Household use
(Applicable in the European Union only)
The symbol (crossed out wheeled-bin) on your product
indicates that the product shall not be mixed or disposed with
your household waste, at the end of its use. This product shall
be handed over to your local community waste collection point
for the recycling of the product.
For more information, please contact the Government Waste-
Disposal department in your country.
Inappropriate waste handling could possibly have a negative
eect on the environment and human health due to potential
hazardous substances. With your cooperation in the correct
disposal of this product, you contribute to reuse, recycle and
recover the product and our environment will be protected.

Disposal of Waste Electrical & Electronic
Equipment of products for Household use
(Applicable in the European Union only)
For further information regarding the disposal of products for
business purposes, please contact your dealer or distributor in
your country. This product shall not be mixed or disposed with
commercial waste.
Warrant y
Danalock International ApS products are covered by a limited
manufacturer warranty. The Danalock International ApS
warranty is limited to the warranty rules and legislation present
in each country. The warranty only covers manufacturing
faults. The warranty does not cover misuse, wrong installation
or damage due to a faulty installation or wrong maintenance.
The invoice act as the proof of warranty, so please keep it as
reference for any warranty complaints.
Qualied Service
Except for batteries, the Danalock V3 contains no user
serviceable or replaceable parts. Non-functioning units must
be returned to an authorized service center for repair or
replacement.
Technical Assistance
If you have a problem and cannot nd the information you
need in the product
documentation, please contact Danalock International
ApS at [email protected] . Please have the following
information ready:
1 Serial number (preferred), MAC address or alias of the lock
2 Username used when registering / installing the lock
3 Username used when getting the error (if dierent
username)
4 Time of incident
CE mark
The Danalock V3 complies with the essential requirements
of the RED directive 2014/53/EU directive with respect to the
radio spectrum, EMC, Health and safety. EU Certicate and
Declaration of conformity (DOC) statements can be downloaded
from the homepage:
https://danalock.com/legal/certicates/
The Danalock V3 is assessed for electromechanically operated
locks and striking plate’s classication matrix compliance (N/A is
equal to “ Not applicable”).
Listed from left to right:
• Category of use,
• Durability,
• Door mass and closing force,
• Suitability for use on re/smoke doors,
• Safety,
• Corrosion Resistance,
• Security for physical attacks,
• Security – Electrical function,
• Security – Electrical manipulation. Detailed Safety
Information
2
(3) (A-C/F-H/L/W
R/S/W/X/Y) (1-9) (0/A-F) (-) (0/A-N/P) (0-7) (0/1) (0-3)
0 - 0 0 3
N/A N/A N/A

Danalock V3 BT
Product specications
Supply Voltage Via USB 4x3V DC (12V DC)
Standby time on
battery
450 Days
Temperature
range
Active operating mode -10ºC to +40ºC
Storage 5ºC to +50ºC
Mechanical
specications
Dimensions (D x H) 59 mm x 59 mm
Weight 130 g(excl bat)
195g (incl bat)
Material Plastic HB
Radio interfaces Bluetooth LE Max 4.7 dBm
E.I.R.P
US and Canada certication marks
This device contains radio transmitters that comply with CFR
47 part 2.1091, Part 15.247 of the FCC rules and with RSS-GEN,
RSS-102 and RSS-247 of Industry Canada requirements
Notice statements according to CFR 47 Part 15.19 /
RSS-GEN:
The device complies with Part 15 of the FCC rules and with
Industry Canada license
exempt standard(s). Operation is subject to the following two
conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including
interference that may cause undesired operation.
Déclarations selon le CFR 47 section 15.19 / RSS-GEN:
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
1 l’appareil ne doit pas produire de brouillage, et
2 l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
NOTICE statements according to CFR 47 Part 15.21:
Changes or modications made to this equipment not expressly
approved by Danalock International Aps may void the FCC
authorization to operate this equipment.
Statements according to CFR 47 Part 2.1091 and
RSS-102:
With respect to radiofrequency radiation exposure Information
it is declared that this equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum
distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Déclarations selon le CFR 47 Sections 2.1091 et RSS-102:
Respectant les informations relatives à l’exposition aux radiations de
fréquences radio, on déclare que cet équipement respecte les limites
d’exposition aux radiations de la FCC aux conditions prévues pour
un environnement non contrôlé.
Cet équipement doit être installé et fonctionner à une distance
minimale de 20 cm entre l’appareil irradiant et votre corps.
Cet émetteur ne doit pas être installé ou utilisé en conjonction avec
d’autres antennes ou d’autres émetteurs.
Japan
The product is approved in Japan with the certicate ID n°:
[R] 202-SMF017
This device is granted pursuant to the Japanese Radio Law (
電波法)
=当該機器には電波法に基づく、技術基準適合証明等を受けた特
定無線設備を装着
している
This device should not be modied (otherwise the granted
designation number will
become invalid)
本製品の改造は禁止されています。（適合証明番号などが無効
となります 。)

Regulatory labeling
The Danalock V3 BT product are regulatory compliant to the
following regulation (Europe, USA/Canada, Japan, Australia/NZ):
REACH
COMPLIANT
RoHS
2011/65/EU
Amendment
2015/863/EU
FCC ID: 2ADSH-V3BT
IC:12588A-V3BT 202-SMF017

Danalock V3 BTZBE / Danalock V3 BTZB
Product specications
Supply Voltage Via USB 4x3V DC (12V DC)
Standby time on
battery
450 Days
Temperature
range
Active operating mode -10ºC to +40ºC
Storage 5ºC to +50ºC
Mechanical
specications
Dimensions (D x H) 59 mm x 59 mm
Weight 130 g(excl bat)
195g (incl bat)
Material Plastic HB
Radio interfaces Bluetooth LE Max 4.7 dBm
E.I.R.P
Zigbee Max 10 dBm E.I.R.P
US and Canada certication marks
This device contains radio transmitters that comply with CFR
47 part 2.1091, Part 15.247 of the FCC rules and with RSS-GEN,
RSS-102 and RSS-247 of Industry Canada requirements
Notice statements according to CFR 47 Part 15.19 /
RSS-GEN:
The device complies with Part 15 of the FCC rules and with
Industry Canada license
exempt standard(s). Operation is subject to the following two
conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including
interference that may cause undesired operation.
Déclarations selon le CFR 47 section 15.19 / RSS-GEN:
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
1 l’appareil ne doit pas produire de brouillage, et
2 l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
NOTICE statements according to CFR 47 Part 15.21:
Changes or modications made to this equipment not expressly
approved by Danalock International Aps may void the FCC
authorization to operate this equipment.
Statements according to CFR 47 Part 2.1091 and
RSS-102:
With respect to radiofrequency radiation exposure Information
it is declared that this equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum
distance of 20 cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
Déclarations selon le CFR 47 Sections 2.1091 et RSS-102:
Respectant les informations relatives à l’exposition aux radiations de
fréquences radio, on déclare que cet équipement respecte les limites
d’exposition aux radiations de la FCC aux conditions prévues pour
un environnement non contrôlé.
Cet équipement doit être installé et fonctionner à une distance
minimale de 20 cm entre l’appareil irradiant et votre corps.
Cet émetteur ne doit pas être installé ou utilisé en conjonction avec
d’autres antennes ou d’autres émetteurs.
Japan
The product is approved in Japan with the certicate ID n°:
V3-BTZBE: [R] 204-920100, V3-BTZB: [R] 202-SMF018
This device is granted pursuant to the Japanese Radio Law (
電波法)
=当該機器には電波法に基づく、技術基準適合証明等を受けた特
定無線設備を装着
している
This device should not be modied (otherwise the granted
designation number will become invalid)
本製品の改造は禁止されています。（適合証明番号などが無効
と な り ま す 。)

Regulatory labeling:
The V3-BTZBE product are regulatory compliant to the following
regulation (Europe, USA/Canada, Japan, Australia/NZ):
For the Danalock V3 BTZB version the following label dierences
are applicable:
REACH
COMPLIANT
RoHS
2011/65/EU
Amendment
2015/863/EU
FCC ID: 2ADSH-V3BTZBE
IC:12588A-V3BTZBE 204-920100
202-SMF018
FCC ID: 2ADSH-V3BTZB
IC:12588A-V3BTZB

Danalock V3 BTZE
Product specications
Supply Voltage Via USB 4x3V DC (12V DC)
Standby time on
battery
450 Days
Temperature
range
Active operating mode -10ºC to +40ºC
Storage 5ºC to +50ºC
Mechanical
specications
Dimensions (D x H) 59 mm x 59 mm
Weight 130 g(excl bat)
195g (incl bat)
Material Plastic HB
Radio interfaces Bluetooth LE Max 4.7 dBm
E.I.R.P
Z-wave Max -10 dBm
E.I.R.P
United Arab Emirates (UAE) certication.
The product has been approved by UAE TRA with registration
number ER75325/19 and the dealer number: DA83047/1
Regulatory labeling:
The Danalock V3-BTZE product are regulatory compliant to the
following regulation (Europe, UAE(Dubai)):
REACH
COMPLIANT
RoHS
2011/65/EU
Amendment
2015/863/EU

Danalock V3 BTZH
Product specications
Supply Voltage Via USB 4x3V DC (12V DC)
Standby time on
battery
450 Days
Temperature
range
Active operating mode -10ºC to +40ºC
Storage 5ºC to +50ºC
Mechanical
specications
Dimensions (D x H) 59 mm x 59 mm
Weight 130 g(excl bat)
195g (incl bat)
Material Plastic HB
Radio interfaces Bluetooth LE Max 4.7 dBm
E.I.R.P
Z-wave Max -10 dBm
E.I.R.P
AUS/NZ:
• The product complies with the AS/NZS 4268 requirements
for Bluetooth LE transceiver and Z-wave 1Tx/1RX (receiver
class 2/3) applications under the Radiocommunications Act
1992; Radio communications (Low Interference Potential
Devices) Class Licence 2015 compilation 2016 May 4.
• The product complies with the requirements of the
relevant standards under Section 134 (1) (g) of the New
Zealand Radiocommunications Act 1989, by the Supplier’s
Declaration of Conformity (SDOC)
Japan:
• The product complies with the requirements of the
ordinance regulating Radio Equipment (2005-08), Art2. item
19 for Bluetooth LE applications.
• The product complies with the ARIB STD-T108 for Z-wave
applications.
• The product is approved in Japan with the certicate ID n°:
[R] 202-SMF019
This product is granted pursuant to the Japanese Radio
Law (電波法)
=当該機器には電波法に基づく、技術基準適合証明等を受け
た特定無線設備を装着している
• This product should not be modied (otherwise the
granted designation number will become invalid)
本製品の改造は禁止されています。（適合証明番号などが
無 効 と な り ま す 。）
Declarations
Certicates and Suppliers Declaration of Conformity (SDOC)
statements can be downloaded from the danalock website:
https://danalock.com/legal/certicates/
Danalock International Aps
Gammel Stillingvej 427C
DK-8462 Harlev
Regulatory labeling
The V3-BTZH product is certied according to the following radio
recommendations (Japan and Australia/New Zealand):
202-SMF019

Danalock V3 BTZU
Product specications
Supply Voltage Via USB 4x3V DC (12V DC)
Standby time on
battery
450 Days
Temperature
range
Active operating mode -10ºC to +40ºC
Storage 5ºC to +50ºC
Mechanical
specications
Dimensions (D x H) 59 mm x 59 mm
Weight 130 g(excl bat)
195g (incl bat)
Material Plastic HB
Radio interfaces Bluetooth LE Max 4.7 dBm
E.I.R.P
Z-wave Max -10 dBm
E.I.R.P
FCC and IC
The V3-BTZU product contains radio transmitters that comply
with CFR 47 Part 2.1091, 15.247 and Part 15.249 of the FCC
rules and with RSS-GEN, RSS-102, RSS-210 and RSS-247 of
Industry Canada requirements.
Notice statements according to CFR 47 Part 15.19 / RSS-GEN:
The V3-BTZU product complies with Part 15 of the FCC rules and
with Industry Canada license exempt standard(s). Operation is
subject to the following two conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including
interference that may cause undesired operation.
Déclarations selon le CFR 47 section 15.19 / RSS-GEN:
Le présent V3-BTZU appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
1 l’appareil ne doit pas produire de brouillage, et
2 l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
NOTICE statements according to CFR 47 Part 15.21:
Changes or modications made to this equipment not expressly
approved by Danalock International Aps may void the FCC
authorization to operate this equipment.
Statements according to CFR 47 Part 2.1091 and OET
bulletin 65 / RSS-102:
With respect to radiofrequency radiation exposure Information
it is declared that this equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum
distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Déclarations selon le CFR 47 Sections 2.1091 et bulletin
OET 65 / RSS-102 :
Respectant les informations relatives à l’exposition aux radiations de
fréquences radio, on déclare que cet équipement respecte les limites
d’exposition aux radiations de la FCC aux conditions prévues pour
un environnement non contrôlé.
Cet équipement doit être installé et fonctionner à une distance
minimale de 20 cm entre l’appareil irradiant et votre corps.
Cet émetteur ne doit pas être installé ou utilisé en conjonction avec
d’autres antennes ou d’autres émetteurs.
Declarations
Certicates and Suppliers Declaration of Conformity (SDOC)
statements can be downloaded from the danalock website:
https://danalock.com/legal/certicates/
Danalock International Aps
Gammel Stillingvej 427C
DK-8462 Harlev
Regulatory labeling
The V3-BTZU product is certied according to the following radio
recommendations of US and Canada:
FCC ID: 2ADSH-V3BTZU
IC:12588A-V3BTZU