danalock V3 EURO Installation instructions manual

Danalock V3 EURO
Mounting guide
www.danalock.com

Page 2

Page 3
Table of contents
Tools needed page 5
Parts involved page 5
Contents of the Danalock box page 6
1. Remove the old cylinder page 7
2. Pull out the old cylinder page 8
3. Adjust the new cylinder page 9
4. Unscrew the small screws page 10
5. Insert the spacer piece and brass tube page 11
Cylinder Size guide page 12 - 13
6. Assemble the cylinder page 14
7. Insert the adjustable cylinder page 15
8. The right rosette spacer page 16
Avoid pulling the cylinder out of place page 17
9. Break the screws to the right length page 18

Page 4
Table of contents
10. Fasten the back plate to the cylinder page 19
Check that the lock still works! page 20
11. Give the tailpiece the right length page 21
12. Attach the tailpiece adaptor page 22
13. Fit the tailpiece page 23
14. Align the plate marks page 24
15. Fasten the Danalock page 25
16. Activate batteries page 26
17. Before downloading the Danalock app page 27
18. Download the Danalock app page 28
19. Dismount instructions page 29
20. LED-Signals page 30
21. Click-commands page 31

Page 5
Tools needed:
To mount the Danalock
you need a Philips
screwdriver and two
pliers or a wire cutter.
Parts involved:
Mortise plate
Lock screw Rosette plate
Cylinder

Page 6
Contents of the Danalock box
Rosette spacers
Back plate Breakable screws Cylinder brass tubes
Tailpiece
adapter
Adjustable cylinder
Keys
4 small
screws
Danalock V3
Small screwdriver

Page 7
1. Remove the old cylinder
First you have to remove your current
cylinder. Unscrew the lock-screw in the
mortise-plate on the side of the door.

Page 8
2. Pull out the old cylinder
Insert your key and turn it so the cam lines up with the
body of the cylinder. Now pull out the cylinder.
cam

Page 9
3. Adjust the new cylinder
Measure the back part (on the outside of your door) of
the old cylinder from the middle of the screwhole and
away (see illustration). In the Danalock box you’ll find an
adjustable lock cylinder.
If the old cylinder and the adjustable cylinder matches - go
to page 11. If they don’t please proceed to the next page.
The tailpiece will always be
directed towards the inside
of the door
Measure from
center of screwhole
Back part
Outside Inside

Page 10
4. Unscrew the small screws on both sides of the
cylinder and pull it apart.

Page 11
5. Insert the same size of spacer piece and brass tube to
make the adjustable cylinder match the old cylinder.
Please look at the size guide on the next pages to find
the right length for the spacer piece and the brass tube.
+7
7

Page 12
Size guide - When you adjust the size of the Danalock
cylinder to the old cylinder you’ll have to exchange the
brass tube in the center with another that fits the spacer
piece. Here are the dierent combinations:
more size guide on next page
The adjustable
cylinder as it is
in the box =
Fits min. 35 mm
+7
=
7 space piece
7
Fits min. 40 mm
+10
=
10
10 space piece
Fits min. 45 mm

Page 13
Size guide - last part
+15
=
15
15 space piece
Fits min. 50 mm
+22
=
22
22 space piece
Fits min. 55 mm
+25
=
25
25 space piece
Fits min. 60 mm

Page 14
6. Assemble the cylinder and screw the small screws back
in on both sides of the cylinder.

Page 15
7. Insert the adjustable cylinder
Insert the new cylinder, and re-insert the lock-screw in
the mortise-plate to fix the cylinder. (b) Do not tighten
the screw to hard - make sure the cylinder is working by
locking and unlocking with your hand.
b

Page 16
8. The right rosette spacer
To avoid pulling the cylinder out of place you need to find
the right spacer or a spacer combination between the rosette
and the back plate.
�
Unscrew the two
breakable screws
that holds the
spacers together
with the adjustable
cylinder.
Choose one or more
spacers so they ush
with the rosette surface.
(See next page)

Page 17
IMPORTANT! Avoid pulling the cylinder out of place.
It is important that the spacer ushes or sticks out from
the hole in the rosette plate.
�
�

Page 18
9. Break the screws to the right length
Depending on which spacer or spacer combination you
chose, it is now important that the screws that fasten the
cylinder to the backplate have the right length. Use this
chart to find the right length:
Use a wirecutter, two pliers or bend the screws forth and
back several times in a vice to break them.
No spacers cut 30 mm
5 mm spacer cut 25 mm
10 mm spacer cut 20 mm
5+10 mm spacers cut 15 mm
10+10 mm spacers cut 10 mm
30 mm
25 mm
20 mm
15 mm
10 mm

Page 19
10. Fasten the back plate to the cylinder
Now fasten the back plate to the cylinder with the
mortise spacer in between them.

Page 20
IMPORTANT! Check that the lock still works!
Make sure that the lock still works properly by turning
the tailpiece. If you can’t lock and unlock this way please
loosen the cylinder screws. (b)
b