danalock V3 SCANDI Product information sheet

Tools needed Parts involved on
your existing lock
tailpiece
tailpiece plate
Danalock V3 SCANDI Easy install page 1/2
3. Normal tailpiece length
Most doors have tailpieces that
extends 10 mm from the doorplate.
They will fit the Danalock without
need for any adjustments to their
lenght!
If the tailpiece is less than 10 mm
long from the door surface, an
extra tailpiece can be found
in the Danalock box.
(See the next illustration no 4).
The Danalock V3 works with
a tailpiece length up to 35 mm
at maximum.
If the tailpiece length
exceeds 35 mm you
will have to shorten it.
(See the illustration no 5).
If the tailpiece is less than
10 mm long you have to
remove the plate that
holds the tailpiece and
replace it with the
tailpiece from the
Danalock box.
You then need to
shorten the new
tailpiece after you
have mounted the
back plate.
(See next illustration).
Place the back plate
where the thumb turn
used to be on your door.
The round hole in the
middle is for the tailpiece.
Use the 2 screws from
the thumb turn to attach
the back plate.
4. Tailpiece too short - insert a new
5. Mounting the
backplate on the door
Thumb turn
2. Remove the current door lock
First you have to remove
the existing thumb turn
on the inside of the door.
1. Secure the front lock
On some doors it can be
helpful to put a piece of
tape across the lock on
the front of the door to
prevent it from falling
when the screws are
removed.
10 - 35 mm
6. Give the tailpiece
the right length
To avoid damaging the
danalock you will have to
shorten the new cylinder
tailpiece to max. 35 mm
from the door surface.
Use two pliers or a wire
cutter to shorten the
tailpiece.
max.
35 mm
Click!
7. Attach the tailpiece adaptor
Choose the green tailpiece
adaptor from the Danalock
box and insert the tailpiece
adaptor in the center tube
on the backside of the
Danalock.
Press on the adaptor
until a click ensures
it is fixed firmly to
the Danalock.
Fit the Danalock over
the back plate.
Make sure the
tailpiece hits the
slide in the middle
of the adaptor.
8. Fit the tailpiece to the middle of the housing base

Go to Google Play or App Store
and download the Danalock App.
When the app is installed you
create a user profile by pressing the
blue ring. You will use this profile
each time you sign into the app.
Next you need to press ”Menu”
in the top right corner, and the
press ”Add lock”.
A guide will now lead you through
the installation and configuration
of your Danalock.
13. Download the Danalock App
Your Danalock is now attached to
the door. Download and open the
Danalock app to finish setting it up.
Leave the door open, so the lock
isn’t influenced when calibrated.
Next you need to press ”Menu”
in the top right corner, and the
press ”Add lock”.
A guide will now lead you through
the installation and configuration
of your Danalock.
14. Add the lock in the app
Pull out the plastic tab
to activate the batteries.
A light will flash to
confirm the Danalock
is ready.
11. Activate batteries 12. Before downloading the app
Note: If the batteries are
disconnected, you will have to
re-calibrate the Danalock.
If at any time you need to dismount
the Danalock from your door, insert
a pen tip into the hole at the top
inner edge of the lock and press
while turning the lock
counter-clockwise until the lock
releases.
This will not reset the lock or
disconnect it from your account, but
the lock may need to be re-calibra-
ted if fastened to your door again.
15. Dismount instructions
page 2/2
Find the small marking on
the edge of the backplate
and align the mark on the
back of the Danalock
baseplate with it.
Now you are sure to hit
the notches on the
backplate with the
Danalock.
9. Align the platemarks
Turn the Danalock
clockwise until it clicks
to fasten it to the back
plate.
NOTE: If you need to
unfasten and retry, see
“Uninstall instructions”
at the end of the
manual.
10. Fasten the Danalock
Click!
Danalock V3 SCANDI Easy install