Danby Designer DAC6003D User manual

USEANDCARE
MANUAL
MANUEL
D'UTILISATiON
Model,Mod_le
DAC6003D
DAC8003D
DAC9003D
DAC6300D
DAC8503D
DACt0003D
DAC12304D
ReadandFollowAllSafetyRules
andOperatinglrlstruct[ons Before
FirstUseofThisProduct.
Veuiliezlifeattentlvamant
leaconslgn_sdes_curit_ellos
Inslructlonsd'utiIiaaUonavant
I'_nsatlonTnttl_tede
re produil.
® @-
® _ ..'-)
Room Air Conditioner
Table of contents ....................... 1
Danby_
Climatiseur de piece
Table of contents ....................... 15
DanbyProductsUmlted,Guelph,OntarioCanadaN1H6Z9
DanbyProductslnc,,Rndtay,OhioUSA,15840
11 C'2

Page
Introduction................................................................ 2
Unit Speclficalions .......................................................... 2
Electrical Specifications ....................................................... 3
Energy-Saving Tips ........................................................... 4
Window _nstallation........................................................... 4
Operating Instructions ....................................................... 11
Care and Maintenance ...................................................... 12
Trouble Shooting Guide ......................................................... 13
Warranty .................................................................. 14
,Exler_or
Air lnIet
Air Inlet Jr_lerior
Air Oullel
Air Fille
-Fresh Air Ventilation Switch
Elee_rentc Conlrols
_,__.Power Cord

Thank you for choosing a Danby Room Air Conditioner to coot your home. This Use and Care Manual
provides information necessary for the proper care and mafntenance of ydur new Room Air Conditioner if
properly maintained, your air conditioner wilt give you many years of trouble free operation. To avoid
installation diffFculttes, read these instructions completely before installing/operating your unit
NOTE: 'This unit Is NOT designed for through-the-wall installation,
For easy reference, you may want to attach a copy of your sales receipt to this page,, Note tel{owing
information provided (on the manufacturer's nameplate located on the right side of the unit above the power
cord), This information wi[ibe needed when you contact a Customer Service Representative,
Model Number:
Serial Number:
Date of Purchase:
Dealer=s Name and Address:
Refer to the trouble shooting section of this Use and Care Manual if the unit is not operating correcUy.
If these suggestions do not solve Ihe problem, contact an authorized service representative or
call Danby TOLL FREE: 1-8OO-26- I_)alllll:_ty"
Keep these instructionsfor future reference,
This symbol denotes a caution or warning
Do not leave a room air conditioner unattended in
a space where people or animals who cannot
reac! to a failed unlt are located. A fai_ed unit can
cause extreme overheating or death in such an
enclosed, una[tended space,
ModelNo.
UnitSpecificatlcat!ons..............
Ve!ls_e
Coo!{ngC_paclty(B[_)
,!q£utWattage
EnemyEfficiencyRating(EER)
FaNOoollngSpeeds
CoolingArea Coverage(Sq,fL)
NoiseLevel (dB)
DAC6003D DACB003D DACg003D
I15W60Hz '115Vt6OHz I15V/60Hz
6,000 8,ooo 9,000
600 810 910
to 9.8 9.8
3/3 3/3 3/3
2O0 325 350
47 49 53
UnitDimensions Width t7.75_
Depth ........... 22.5"
Height .l&5"
t7,75' 22_
2,?-5" 24,25"
13.5" 14.75"
W;ndow Kit Dimensions
Shipping Weight
Maximum Width 37'
MJnlrnumWidth 24o5=
Mtr_mum Height 15o5"
97 Ib
37" 40"
24.5" 28"
1&5" 17,8°
97 Ib !08 lb
NOTE: Specifications are subject to change w_lheutnoticefor further improvement.
2

Model No.
Unit Specificafications
voltage......
Inputwattage
EnergyEfllcien.cy.Ra!'in9lEER)
FantCooi!n_Speeds
Cooling]AreaCoverage{Sq.!l:.)...
NoiseLevel(riB)
DAC6360D DAC8503D DACI0O030 DAC12304D
115VIeOHz 1I 5V/e0Hz 115VI6OHz 115V/60Hz
6,300 B,50C, 10_000 12,000
640 860 1000 1220
9.8 9.8 10 g.8
313 3/3 3/3 3/3
2t5 350 450 500
47 55 53 56
Unl! Dtrnan_ton,_ ,_W/dth 17,75-
Depth 22.5"
,, He!911_..... 13,5"
22::: 22" 22"
2_,25_ 24,25" 24,25"
14,75" 14.75" t4.75"
Window Kif Oimenslons Maximum__j_tb 37" ,.......
Minimum Width 24,5':,
Minimum He!_h! 15.5 _
Shipping Weight 97 Ib
40" 4(, 40"
17.8" 17,8" 17.S"
108 lb 108 Ib 10B Ib
jl IIIIIIRIIIi i ii i , ,
m .11_I,tif111,_;II!."]_-,'_l,lt_[lf';_!i tel_[..t
1. All wiring must comply with local and national
electrical codes end must be installed by a
qualified electrician, if you have any questions
regarding the following instructions,contact a
quaUlied electrician,,
2, Check available power supply and reseive any
wiring problems BEFORE installingand
operating this unit,
3. This 115V air conditioneruses 12,0 or less
nameplate amps and may be used in any
properly wired, general purpose household
receptacle. SeeTable 1 for specifications for
individual branch circuit
For your safety and protection, this unit is
grounded through the power cord plug when
plugged into a matching wall eerier. If you are
not sure whether your wall outlet ts properly
grounded, please consult a qualified
electrician.
5_ The wail outlet (3-pin) must match the plug (3-
pin) on the serv[ce cord supplied with {he unit.
DO NOT use piug adapters. See Table 2 for
receptacle end fuse infoTmation.If it is necessary
touse an extension cord to connect your air
conditioner, use an approved "air conditioner"
extension cord only_(available at most local
hardware stores)
6 The rating plate on the unit contains electrical
and other technical data The rating plate
is located on the right side of Ihe unit, above the
power cord
Tab]e 1: Suggested Individual Branch CircuI_
NameplateAmps AWG Wire S_ze"
5.0 to 12 14
AWG- AmericanWire Gage
* Based on copperwireat 60°C temperature rating.
'Table 2: Receptacle and FuseTypes
Ra_edVeils 125
Amps 15
WallOutlet _
FuseSize 15
Time DelayFuse PlugType
(orcircuitbreaker)

_ _f I_l[=t'i_.'/-\,tl#l_iliii_-'-,-.--.-,l_
Your Room Air Conditioner unit is designed lo
be highly efficient in energy savings. Follow
these recommendations for greater efficiency°
1.. Select thermostat setting that sUlISyour
comtort needs and leave thermostat at that
chosen setting°
2_ The air filter is very efficfenl in removing airborne
dust particles. Always keep the air filter clean.
3. Use drapes, curtains, or shades to keep
direct sunllghl from heating room, but DO NOT
obstructthe air conditioner.. Allow air to circula|e
around the untt without obstruction.
4_ Start your air conditioner before outdoor air
becomes hot and uncomfortable.,This avoids an
initi_l period of discomfort while tJnlt is cooling
off the room.
When outdoor lemperatures are cool enough,
use HIGN, MED, or LOW FAN only {depending
on your model), This clmulales indoor air,
providingsome cooling comfort, and utilizes
lesselectricity than Whenoperating on a
cooling setting..
J_YtlIi ilIWiilf,,'i Id I l;liCilt
IITo avoid the possibility ofpersonal l
I injury, disconnect power to the unit t
i beforetnslalllng orservicing, j
Tools Needed for Window Installation
Screw Drivers: Both Phillips and flat head
Power Drill: 1/8 inch diameter drill bit
Penctl
Measuring Tape
Scissors
Carpenters Level
Adjustable Wrench
{ T__perat_on difficulties,
read thes te nstru_ns thoroughly.
YourRoom Air Cond{tioner Is designed for easy
inslallation in a single or doubEe-hung window.NOTE:
This unit is NOT designed forverlical (slider type)
windows and/or through-the-w_} appiicationslNOTE:
Save the shipping carton and packing materials for
_uture storage or transporl of the unit.. Remove from
carton, the plastic bag containing the installation
hardware kit necessary for the installation ofyour air
condltlone_. Please check the contents of hardware
kit agaist the corresponding model check list. prior to
Installation of the uniL
-See F!g. t

Because the compressor Is located on the controls
side of the unit (right side), this side will be heavier
and more awkward to manipulate° Inadequate
support on control side of the unit can result in
personal injuryand damage toyour unit and
property.Therefore, itis recommended to have
someone assist you during the insial/ation of this
unit..
Your unitIs designed to evaporate condensation
under normal conditions. However, under
extreme humidity conditions, excess condensation
may cause basepan to overflow to the outside_
The Unit should be installed where condensation
run-off cannot drip on pedestrians or ne}ghboring
properties
Adrain tube connection (exctuding hose) is provided
to redirect condensation ovedlow See Fig,.25
1, Select the Best Location
Ao This room air conditioner ts destgned lo fit easily
into a single or double hung window. However,
since window designs vary, it may be necessary
to make some modifications for sate, proper
Installation.
Bo Make sure window and frame is structurally
sound and free from dry and rotted wood,
C. For maximum efficiency, install the air condilioner
on a side of ahouse or building which favors
more shade than sunlight_ If the unit is tn direct
sunlight, it is advisable to provide an awning over
the unit,.
CoProvidesufficient clearancearound the cabinetto
a!lowfor ample atrcirculationthroughthe unit,
See Fig,2, The rear ofthe unitshould be
outdoorsand not in a garagenorinside a
building. Keepunit asfaraway as possiblefrom
ob_tacleslobstructionsand at least30" abovethe
floororground, Curtainsand otherobjectswtth]n
aroomshouldbe preventedfrombrookingthe air
flow.
E. Be certain the proper electrical outlet is within
reach of the Inslallationo Use only a single
outlet circuit rated at 15 ampso All wiring should
be in accordance with loca! and national
electrical codes.
F. DO NOT USE "REGULAR" EXTENSION CORDS
WITH THIS UNIT, If it is necessary to use an
extension cord to connect your air conditioner,
use an approved "air conditioner" extension cord
only (available at most local hardware stores)
G. DO NOT insta|l unit where leakage of combustible
gas is suspected. Your air conditioner may fail to
operate In air containing oils (including machine
oils), sulfide gas, near hot springs, etc...
30"
Slde Min
obstrucllon
Ground ,,_>
FIg_2

1. Preparation to Remove the Air Conditioner
Slide-Out Chassis (All Models)
*Posftion the air conditioner in the normar
(upright) position°
• Remove the air filter by grasping the lJltarhandle
(on front gd]t) and s_[ding It to the rlghL Fig 2
*Remove the phillips screw (behlnd filter)
seoudng the grill front to the chassis. (Fig. 4)
, Remove the phillips screws located on 1he(lower
left.fright) edge of front grill (Fig.3)
• To remove the front grill, grasp the lower front
corner of the grill, puiting(gen!ly) outward and
upward. (Fig.5)
Repeat this step on the 3remain|rig comers..
,Before the front grill can be completely removed
from the cabJnel, it wilt be necassary to
disconnect the (maleliemale) eleclrlcal wire
harness located directly behind the front gr_l..
{Fig 5a)
• _emov_ the two phfllfps screws (lower left/right
side of cabinet) securing the slide-ouFchassb Io
the cabinet. Fig.7
NOTE: These screws must be reinstalled
upon completion of the window installation.
(to secure slide-out-chassls)
NOTE: Some models may be inclusive of an
additional (slide-out chassis) retaining bracket and
screw located at the front of the chassis. This
bracket and screw must also be removed before
attempting to remove the sF_e-out chassis Fig_ 6
NOTE:This bracket and screw does not have to
be reinstalled upon compbtlon of the window
installation.
Grasp the pull handle at the front of the slide-out-
chassis and carefully slide the air conditioner out
of the cabinet. (Fig.6)
Please seek assistance for this procedure.
Fig.1 Ftg.2
FRONT PANEL
;/
Fig. 3Fiff_4
FIg, 5a Flg_s
Fig. 6.
tg_ out
._ltJw
Fig 7

2. Assembly of 1he Upper & Lower Channels,
to CabineL (All Models)
•"L" ShapedTopChannel:Install the"L" shaped
channeltothetop oFthecabinetas showninFig,
8 usingfour (4) 1/4"screws.
• "U;' ShapedBottomChannel:Installthe "U"
shapedchannelto thebottomof thecabinelas
shownthFig.8 usingfour(4) 1/4"screws_
NOTE.Somemodelsmay alreadyhavethe
bottom channelfactory Installed,
3. Assembly of the Side Curtains to Cabinet.
(All Models)
,Slidetheshutters intothetopand boltom
channelsas shown inFig,9.The shultersare
idsnlified (on frame)as left & right Attach the
shuttersto thecabinetusingfour 1/4"screws on
eachside.
4. Installation of Mounting Brackets and First
Sealing Strip (All Models)
SPECIAL NOTE; Windows come in avariety of
different designs and styles_ Therefore, it may be
necessary to modify or Improvise on your
particular installation.
A. Attach the bracket assembly to the 90° angle
support brackets (Fig., 16) using four 1-H2" x
114" bolts. (two bolts perbracket)
Secure with the four 114" lock washers and four
1t4" nuts. DO NOT immediately tighten these
bolts as it may be necessary to adjust the depth
of the bracket assembly, depending on the
depth of your window sill SeeFig's.18& I9o
Tea! the bracket assembly Inthe window before
Installing, if satisfied, tighten all bolts. Install the
two levelling screws tnto the 90° support
brackets.See Fig. 16 If the levetling screwsare
distanced too far away from the wall to provide
adequate stability, it may be necessary to shim
this area with a solid piece of wood. See Fig 19,
B° Measure the length o1the inside sill and lind the
center as shown in Fig. t"7.
ModeIs:DAC6OO3D, DACeOO3D & DAC6300D:
Measure 8.071" (205ram) on each side ofcenter
and mark these points.
Models:DAC9003D,DAC8503D,DAC |0003D &
DAC12304D:Measure 10.315" (262mm) on each
side of center and mark these poinlSo
Align the V-slot on the brackel with each
cbrrespending mark and mount the brackets to
the silt uping two 314"screws & two flat washers
per oracKet
Brackets should be pe_'pendicular to the inside
window sill, wiIh step (U) bracket tight against the
sill. See Fig. 18.
C. For proper condansatlon rumolf It will be
necessary toadjust the angle/pitch of the window
brackets. This is accomplished by adjus!ing the
distance of the leveling screw on the outer wall.
The maximum angle/pitch should not exceed
more than 3116". See Fig. 18
I/4"Screw
"L" Shaped
Channel
Channels
"Lr' Shaped
Channel
Fig. S
Shutters
Fig,9
V-alol"_--_ o o o =o o o o ]
tavailing Screws _ _ Support Btackels
Fig.16

?0 _, o o o 0o o oo r_'__':=:=
OuterWaltCoas_rucUon
FIg_18
5. Installation of the Cabinet
(All Models)
A, Place the air conditioner cabinet inlo the w_ndow
with the "U °shaped mounting channel (on top)
positionedin front of the upper wlndow sash. The
"U" shaped channel on the botlom of the cabinet
should be positioned in the "recessed" portion el
the track located at the front of the window
brackets. Pull the window down until it rests just
behind the Iront flange of the (top) "U' shaped
mounting channel. See Fig, 14.
Be Align one hole in the bottom of the cabinet wllh
one hole in the bracket assembly_ Secure the
cabinet !o the bracket using a 1/4" screw
provided. Repeat the same procedure on the
opposite side of the cabinet Fig. 15
C, Checkto makesure the"pitch" (angle)ofthe
cabinetlsslanted slightly downwardonthe
outside, If necessary,re-adjustthe levelling
screwsIn the mountingbracket,Fig..18
D, Cut the flrs_tfoam sealing strip to fit the
underside (bottom) of the lower wlndow sash.
Remove the peel-off, backing on lhe foam and
attach the foam stdp to the sash. See Fig. 13.
WindowSash
"L"Shaped Foam Sllip
Moun_n_
Channel
Fig. 14

6. Installing the Slide-Out Chassis into Cabinet:
(please seek assistance forthis procedure)
•Carefu]|y slide the air conditionerback into
the cabinet. (in window)
Note: Ground wire must be re-installed
before completing next step,
•Reinsta!l (slide-out-chassis) security screws
removed earlier from the (lower left/rlght) side of
the cabinet. Fig 7
•Expand the shutter frames (fuIly) on each side
and secure the top el the shutter frame to the
window sash using one 3/4" screw & flat washer
on each side_F'ig,23
•Install a shutter clamp on each side of the
(lower) shuiler frame and secure to window sill
usrng one 3/4" screw & fiat washer on each aide.
Figo23
7. Reinstalling Front Grill (All Models) :
Before re-Installing the front grill back on the
cabinet, you must re-connect the (male/female)
electrical wire harness between the front gdlt
controlpanel and the main (cabinet) unit
(Ftg,Sa) Make sure the elecldcai connection is
t_rmiyand securely attached,
• Position the front panel on the cabinet slarfing at
the top. The front panel lock tabs must be
inserted Into the retainingslols in the cabinet.
• Repeat this procedure on all sides, making sure
the fresh air ventilation lever arm and power cord
are properly installed back to their original
position on the front griilo
°Secure the front grilt Io the cabinet using the
phillips screws removed earlier. Fig's, 3& 4
• Re-install the air filler.
_, Cut the second foam seal to fit the opening
between thelop inside and outsidewindow.
See Fig_24,
-Some installations may requireadditional sealing
around the _ndow and air conditioner,Check for
any air teaks and seat where necessary.
• Under very humidconditions, water removalmay
be excessiveenough to ovedlow from the rear of
the unit or increase noise Ievels of the air
conditioner.If thisoccurs, you may want to attach a
section of (garden) drain hose (not included) to
the drain plug located at lhe rear of the unit, thts
wtll permit condensation torun off more
conveniently. See Fig.25
Fig 7
Shutter
r-_Clamp
Fig, 23
-- 2ridFoam
Seal
Fig,, 24
j =1 H -
r
t'_'_,_ Dta}nHose
(nolintruded)
Fig, 25