Danby DPA120B1WB User manual

Thank you for purchasing a Danby air conditioner. Please
read this onwer’s manual carefully before using your new
air conditioner.
Remote Control Instructions
MODEL
AIR CONDITIONER
DPA120B1WB
DPA140B1WB
30.12.13
DPA110B2WDD
DPA120B3WDB

1
2
3
4
6
7
7
7
8
8
9
12
Handling the Remote Control...................................................
Function Buttons ......................................................................
Indicators on LCD Display .......................................................
Operating the Buttons ..............................................................
Auto Operation Setting .............................................................
Swing Setting.............................................................................
Timer Setting..............................................................................
Economy Setting........................................................................
CONTENTS
Remote Control Specifications................................................
Cooling/ Fan Setting .................................................................
Dehumidifier Setting .................................................................

Use the remote control within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
Location of the Remote Control.
CAUTIONS
The air condiitioner will not respond if curtains, doors or other materials
block the signal from the remote control tothe unit.
esopxetonoD.lortnocetomerehthtiwtcatnocmorfdiuqilynatneverP
the remote control to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react tothe remote control, either move
these appliances to another location or consult your local dealer..
The remote control is powered by two dry
part and protected by a cover.
(1) Remove the cover by pressing down and sliding it off.
(2) Remove the old batteries and insert the new
batteries,placing the(+) and (-) ends correctly.
(3) Reattach the cover by sliding it back into
position.
NOTE: When the batteries are removed, the
remote control erases all programming.
After inserting new batteries, the remote
controll must be reprogrammed.
Replacing the Batteries
.
Handling the Remote Control
2
batteries(2-AAA) located in the rear

Model
Rated Voltage
Remote Control Specifications
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range: 17°C ~30°C (62°F~86°F).
4. Full Function of LCD (Liquid Crystal Display)
Environment
Signal Receiving Range
Performance Feature
CAUTION
Do not mix old and new batteries or batteries of different types.
Do not leave the batteries in the remote controller if it is not going
to be used for more than 2 months.
Dispose of the old batteries in special containers such as those
foundin the sales outlets.
3
NOTE:
All the illustrations in this manual are for explanatory purposes only.
Your air conditioner may be
NOTE :
3.0V( 2-AAA
8m
)
1. Operating Mode: AUTO, COOL, DRY,
and FAN.
RG51I46/BGCE
-5°C to 60°C (-41°F to 140°F)
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
1) Reorient or relocate the receiving antenna
2) Increase the separation between the equipment and receiver
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
4) Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not approved by the party responsible for FCC compliance could void the user’s
authority to operate the equipment.
This appliance complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired
operation.
CAN ICES-3 (B) / NMB-3 (B)
Temperature setting display: press and hold the UP and DOWN buttons at the same time for
3 seconds to alternate the temperature display between °C and °F.

1
TEMP DOWN Button
Push this button to decrease the indoor temper-
ature setting by 1°C (2°F) increments to 30°C (86°F)
2
TEMP UP Button
Push this button to increase the indoor temper-
ature setting by 1°C (2°F) increments to 17°C (62°F)
Each time the button is pressed, the operation
mode changes in the following sequence:
3
MODE Button
4
4
Used to stop or start louver movement and
move the airflow direction up/down as desired.
5
6
Button
Once the recessed RESET button is pressed,
all of the current settings will be cancelled
and the controller will return to default settings.
7
Button
Operation starts when this button is pressed
and stops when the button is pressed again.
AUTO
COOL
DRY
FAN
Used to select the fan speed in four steps:
Auto Low Med High
Button
Button
8
Press this button to activate the Auto-on time
setting. Each time it’s pressed will increase the start
time by 30 minute increments, up to 10 hours, then
by 1 hour increments up to 24 hours.To cancel the
Auto-on time setting, just press the button until
the time setting is 0.0.
9
Button
Select this function if you want the unit to maintain
a comfortable setting and save energy while you sleep.
mode only.
12
4
3
6
5
7
8
9
10
11
12
Model: RG5 ECGB/64I1
Button
This function is available on COOL, or AUTO
Press and hold the UP and DOWN buttons at the same
time for 3 seconds to alternate the temperature display
between °C and °F.
Function Buttons

Function Buttons (continued)
Button: Press the timer button to activate
the AUTO-OFF setting. Each time it’s pressed
increases the time setting by 30 minute increments
for the first 10 hours, then by 1 hour increments up
to 24 hours. To cancel the AUTO-OFF setting, press
the button until the setting displays 0.0.
Button: Press this recessed button to lock all
current settings, and the remote control will not
accept any changes except for unlocking. Use the
LOCK mode when you want to prevent settings from
changing accidentally. Press the LOCK button again
to cancel the LOCK function. A LOCK symbol will
appear on the remote control display when the
LOCK function is activated.
5
10
11
.
LED Display Button: Press this button to clear the
unit’s display, press it again to light the display.
12
NOTE: While the unit is running in sleep mode, it
MODE buttons
are pressed.
ro,,filecnaclliw

6
TIMER ON OFF
SET TEMPERATURE
Transmission Indicator
Temp./Timer Display
FAN SPEED Display
MODE display
ON/OFF Display
This transmission indicator will light up when the remote
control transmits signals to the indoor unit.
Displays the current selected mode. Including AUTO,
COOL, DRY
, and FAN.
The temperature setting, from 17°C (62°F)
30°C (86°F) or timer setting (0~24h) will be displayed.
If FAN mode is selected, there will be no display
.
This indicator will be displayed when the unit is
operating.
Displays the selected fan speed: AUTO, HIGH, MED
or LOW. Nothing is displayed when the fan speed is
on AUTO speed. When AUTO or DRY Mode are
selected, there will be no signs displayed.
MODE Display (FAN mode)
Indicators on the LCD
TIMER DISPLAY:
This display area shows the TIMER settings. That is, if
only the Auto-on function is set, it will display TIMER
ON. If only the Auto-off time function is set, it will
display TIMER OFF. If both functions are set, it will
display TIMER ON OFF which indicates you have
chosen both the Auto-on and Auto-off setting.
LOCK INDICATOR:
The LOCK icon is displayed after pushing the LOCK
button. Push the LOCK button again to clear display.

7
Ensure the unit is plugged in and has power.
How to use the buttons
4
Auto Operation
Ensure that the unit is plugged in and has power.
The OPERATION indicator will illuminate on the
display panel of the unit.
1. Press the MODE button until AUTO is selected.
2. Press the TEMP button to set the desired
temperature. The temperature can be set within a
range of 17°C (62°F) to 30°C (86°F) by 1°C (2°F)
increments.
conditioner.
NOTE
1. In the auto mode, the air conditioner can
automatically choose the mode of Cooling, Fan,
difference between
the actual room temperature
and the set
temperatrue on the remote control.
2. In the auto mode, you can’t switch the fan speed.
3. If the auto mode doesn’t suit you, the desired
mode can be controlled manually.
Cooling / Fan Operation
1. Press the MODE button to select COOL,
FAN mode.
2. Press the TEMP button to set the desired
temperature. The temperature can be set within a
range of 17°C (62°F) to 30°C (86°F) in 1°C (2°F)
increments.
3. Press the button to select one of
4 fan speeds -Auto, Low, Med, or High.
4. Press the button to start the air
conditioner.
NOTE
In the FAN mode, the temperature setting is not
displayed in the remote control and you are not
able to control the room temperature either. In this
case, only step 1, 3, and 4 may be performed.
1
3
2
Dehumidifying by sensing the
1
3
2
3. Press the button to start the air

8
Ensure the unit is plugged in and has power.
The
OPERATION
indicator on the display
panel of the unit illuminates.
Swing Setting
airflow direction.
2 seconds, the auto-swing feature of the louver
is activated. The horizontal louver will swing
up/down automatically. Press it again to stop.
NOTE: When the louver swings or moves to a
position which would affect the cooling
it will
automatically change the swing/
moving
direction.
Dehumidifying Setting
selected.
2. Press the TEMP button to set the desired
temperature. The temperature can be set within a
range of 17°C (62°F) to 30°C (86°F) by 1°C (2°F)
increments.
ing mode.
1
3
2
1
Use the button to adjust the Up/Down
ability of the air conditioner,
1. Press the MODE button until DRY mode is
3. Press the
button to start dehumidify-
1. If the button is held down for more than

9
Timer Setting
will set the auto-off time of the unit.
control will display TIMER ON, the last auto-on
time setting and the LCD display area will show
an ‘h.’ Now it’s ready to reset the auto-on time.
auto-on time. Each time you press the button,
the time increases by 30 minute increments, up
to 10 hours, then by 1 hour increments up to 24
hours.
3. After turning the TIMER ON, there will be a one-
half second delay before the remote control
transmits the signal to the air conditioner. Then,
after approximately 2 more seconds, the “h”
will disappear and the set temperature will
re-appear on the LCD display window.
To Set theAuto-On Time.
To Set theAuto-Off Time.
control will show TIMER OFF, the last auto-off
time setting, and the LCD display area will show
an “h.” Now it is ready to reset the auto-off time.
desired auto-off time. Each time you press the
button, the time increases by 30 minute
increments up to 10 hours, then by 1 hour
increments up to 24 hours.
3. After setting the TIMER OFF ,there will be a one-
half second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.
1
2
Pressing the button will set the auto-on
time of the unit. Pressing the button
1. Press the button. The remote
2. Push the button again to set the desired
1. Press the button. The remote
2. Push the button again to set the