Danfoss VLT AutomationDrive FC 360 User manual

MAKING MODERN LIVING POSSIBLE
Quick Guide
VLT®AutomationDrive FC 360
vlt-drives.danfoss.com

Contents
1 Introduction 3
1.1 Purpose of the Manual 3
1.2 Additional Resources 3
1.3 Document and Software Version 3
1.4 Approvals and Certications 3
1.5 Disposal 3
1.6 Product Overview 3
2 Safety 7
2.1 Safety Symbols 7
2.2 Qualied Personnel 7
2.3 Safety Precautions 7
3 Quick Start 9
3.1 Identication and Variants 9
3.2 Hand On/Auto On Mode 10
3.3 Application Selections 10
3.4 Jumper Terminal 12 and 27 14
3.5 Automatic Motor Adaptation (AMA) 14
4 Installation 15
4.1 Mechanical Installation 15
4.2 Electrical Installation 16
4.3 Serial Communication 22
5 Local Control Panel and Programming 23
5.1 Local Control Panel (LCP) Operations 23
5.2 Main Menu 25
5.3 Quick Menu 27
5.4 PM Motor Set-up 29
5.5 PROFIBUS 31
5.6 PROFINET 32
5.7 Parameter List 33
6 Application Examples 39
7 Diagnostics and Troubleshooting 43
7.1 Warning and Alarm Types 43
7.2 Warning and Alarm Displays 43
7.3 Warning and Alarm Code List 44
7.4 Error Code List 46
Contents Quick Guide
MG06A602 Danfoss A/S © 04/2015 All rights reserved. 1

7.5 Troubleshooting 46
8 Specications 48
8.1 Mains Supply 3x380–480 V AC 48
8.2 General Technical Data 51
8.3 Fuses 55
8.4 Connection Tightening Torques 56
Index 57
Contents VLT®AutomationDrive FC 360
2 Danfoss A/S © 04/2015 All rights reserved. MG06A602

1 Introduction
1.1 Purpose of the Manual
The quick guide provides information for safe installation
and commissioning of the frequency converter.
The quick guide is intended for use by qualied personnel.
Read and follow the quick guide to use the frequency
converter safely and professionally, and pay particular
attention to the safety instructions and general warnings.
Always keep this quick guide available with the frequency
converter.
VLT®is a registered trademark.
1.2 Additional Resources
Other resources are available to understand advanced
frequency converter functions and programming.
•The programming guide provides greater detail on
working with parameters.
•The design guide provides detailed capabilities
and functionality to design motor control
systems.
•Optional equipment is available that may change
some of the procedures described. Be sure to see
the instructions supplied with those options for
specic requirements.
Contact the local Danfoss supplier for technical documen-
tations.
1.3 Document and Software Version
The quick guide is regularly reviewed and updated. All
suggestions for improvement are welcome.
Edition Remarks Software version
MG06A6xx Replaces MG06A5xx 1.5x
1.4 Approvals and Certications
Illustration 1.1 Approval
1.5 Disposal
Do not dispose of equipment containing
electrical components together with
domestic waste.
Collect it separately in accordance with
local and currently valid legislation.
1.6 Product Overview
A frequency converter is an electronic motor controller
that converts AC mains input into a variable AC waveform
output. The frequency and voltage of the output are
regulated to control the motor speed or torque. The
frequency converter can vary the speed of the motor in
response to system feedback, such as changing
temperature or pressure for controlling fan, compressor, or
pump motors. The frequency converter can also regulate
the motor by responding to remote commands from
external controllers.
In addition, the frequency converter monitors the system
and motor status, issues warnings or alarms for fault
conditions, starts and stops the motor, optimises energy
eciency, and oers many more control, monitoring, and
eciency functions. Operation and monitoring functions
are available as status indications to an outside control
system or serial communication network.
Introduction Quick Guide
MG06A602 Danfoss A/S © 04/2015 All rights reserved. 3
11

1.6.1 Enclosure Types and Power Ratings
Enclosure size
380–480 V J1 J2 J3 J4 J5 J6 J7
Power size
[kW]
0.37–2.2 3.0–5.5 7.5 11–15 18.5–22 30–45 55–75
Dimensions
[mm]
A
a
D
C
B
b
130BC449.10
Height A 210 272.5 272.5 317.5 410 515 550
Width B 75 90 115 133 150 233 308
Depth C
(with option B) 168 (173) 168 (173) 168 (173) 245 (250) 245 (250) 241 323
Mounting holes
a 198 260 260 297.5 390 495 521
b 60 70 90 105 120 200 270
Mounting screw M4 M5 M5 M6 M6 M8 M8
Table 1.1 Enclosure Sizes, Power Ratings, and Dimensions
Introduction VLT®AutomationDrive FC 360
4 Danfoss A/S © 04/2015 All rights reserved. MG06A602
1
1

1.6.2 Exploded Views
130BC439.10
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
03
02
01
05
04
1 NLCP (accessory) 10 2-pole relay 2 (0.37–7.5 kW), pluggable
3-pole relay 2 (11–22 kW), pluggable
2 Control cassette 11 Mains terminals
3 RFI switch (screw M3x12 only) 12 Cable strain relief (accessory for 0.37–2.2 kW units)
4 Removable fan assembly 13 Pluggable RS485 terminal
5 Grounding clamp (accessory) 14 Fixed I/O terminals
6 Screened cable grounding clamp and strain relief (accessory) 15 Fixed I/O terminals
7 Motor terminals (U, V, W), and brake and load sharing terminals 16 Terminal cover
8 PE ground 17 B options (MCB 102/MCB 103 accessories)
9 3-pole relay 1
Illustration 1.2 Exploded View, J1–J5 (0.37–22 kW), IP20
Introduction Quick Guide
MG06A602 Danfoss A/S © 04/2015 All rights reserved. 5
11

3
2
1
18
17
16 15 14
13 12
11
10
9
8
7
6
5
4
130BD647.10
1 J7 frequency converter 10 I/O cable clamps
2 Removable fan assembly 11 Terminal cover
3 M5 screw X4 (for fan assembly) 12 Motor terminals
4 NLCP (accessory) 13 Load sharing terminals
5 B options (MCB 102/MCB 103 accessories) 14 Removable plugger (for load sharing terminal)
6 I/O terminals 15 Screened cable grounding clamps
7 I/O terminals 16 Mains terminals
8 Pluggable RS485 terminals 17 Decoupling plate (accessory)
9 Relay terminal 1&2, xed 18 M4 screw X3 (for decoupling plate)
Illustration 1.3 Exploded View, J7 (55 kW, 75 kW), IP20
Introduction VLT®AutomationDrive FC 360
6 Danfoss A/S © 04/2015 All rights reserved. MG06A602
1
1

2 Safety
2.1 Safety Symbols
The following symbols are used in this document:
WARNING
Indicates a potentially hazardous situation that could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation that could
result in minor or moderate injury. It can also be used to
alert against unsafe practices.
NOTICE
Indicates important information, including situations that
can result in damage to equipment or property.
2.2 Qualied Personnel
Correct and reliable transport, storage, installation,
operation, and maintenance are required for the trouble-
free and safe operation of the frequency converter. Only
qualied personnel are allowed to install or operate this
equipment.
Qualied personnel are dened as trained sta, who are
authorised to install, commission, and maintain equipment,
systems, and circuits in accordance with pertinent laws and
regulations. Additionally, the personnel must be familiar
with the instructions and safety measures described in this
manual.
2.3 Safety Precautions
WARNING
HIGH VOLTAGE
Frequency converters contain high voltage when
connected to AC mains input, DC supply, or load sharing.
Failure to perform installation, start-up, and maintenance
by qualied personnel can result in death or serious
injury.
•Only qualied personnel must perform instal-
lation, start-up, and maintenance.
WARNING
UNINTENDED START
When the frequency converter is connected to AC mains,
DC supply, or load sharing, the motor may start at any
time. Unintended start during programming, service, or
repair work can result in death, serious injury, or
property damage. Start the motor with an external
switch, a eldbus command, an input reference signal
from the local control panel (LCP), via remote operation
using MCT 10 software, or after a cleared fault condition.
To prevent unintended motor start:
•Disconnect the frequency converter from the
mains.
•Press [O/Reset] on the LCP before
programming parameters.
•Ensure that the frequency converter is fully
wired and assembled when it is connected to
AC mains, DC supply, or load sharing.
WARNING
DISCHARGE TIME
The frequency converter contains DC-link capacitors,
which can remain charged even when the frequency
converter is not powered. Failure to wait the specied
time after power has been removed before performing
service or repair work, could result in death or serious
injury.
1. Stop the motor.
2. Disconnect AC mains, permanent magnet type
motors, and remote DC-link power supplies,
including battery back-ups, UPS, and DC-link
connections to other frequency converters.
3. Wait for the capacitors to discharge fully, before
performing any service or repair work. The
duration of waiting time is specied in Table 2.1.
Voltage [V] Minimum waiting time (minutes)
4 15
380–480 0.37–7.5 kW 11–75 kW
High voltage may be present even when the warning LEDs are
o.
Table 2.1 Discharge Time
Safety Quick Guide
MG06A602 Danfoss A/S © 04/2015 All rights reserved. 7
22

WARNING
LEAKAGE CURRENT HAZARD
Leakage currents exceed 3.5 mA. Failure to ground the
frequency converter properly can result in death or
serious injury.
•Ensure the correct grounding of the equipment
by a certied electrical installer.
WARNING
EQUIPMENT HAZARD
Contact with rotating shafts and electrical equipment
can result in death or serious injury.
•Ensure that only trained and qualied personnel
perform installation, start-up, and maintenance.
•Ensure that electrical work conforms to national
and local electrical codes.
•Follow the procedures in this manual.
NOTICE
HIGH ALTITUDES
For installation at altitudes above 2000 m, contact
Danfoss regarding PELV.
CAUTION
INTERNAL FAILURE HAZARD
An internal failure in the frequency converter can result
in serious injury, when the frequency converter is not
properly closed.
•Ensure that all safety covers are in place and
securely fastened before applying power.
NOTICE
Use on Isolated Mains
For details about the use of the frequency converter on
isolated mains, refer to section RFI Switch in the design
guide.
Follow the recommendations regarding the installation
on IT-mains. Use relevant monitoring devices for IT-mains
to avoid damage.
Safety VLT®AutomationDrive FC 360
8 Danfoss A/S © 04/2015 All rights reserved. MG06A602
2
2

3 Quick Start
WARNING
Improper use could result in death, serious injury,
equipment, or property damage. Before installing or
using the equipment, carefully read chapter 2 Safety and
chapter 4 Installation.
3.1 Identication and Variants
Conrm that the equipment matches the requirements and
ordering information by checking power size, voltage data,
and overload data on the nameplate of the frequency
converter.
130BC435.11
CHASSIS/IP20
VLT
MADE BY DANFOSS
IN CHINA
AutomationDrive
www.danfoss.com
R
T/C: FC-360HK37T4E20H2BXCDXXSXXXXAXBX
P/N: 134F2970 S/N: 691950A240
0.37 kW 0.5HP High Overload
IN: 3x380-480V 50/60Hz 1.24/0.99A
OUT: 3x0-Vin 0-500Hz 1.2/1.1A(Tamb. 45 C)
o
1
2
3
CAUTION:
SEE MANUAL
WARNING:
AND LAODSHARING BEFORE SERVICE
STORED CHARGE DO NOT TOUCH UNTIL 4 MIN. AFTER
DISCONNECTION
RISK OF ELECTRIC SHOCK-DUAL SUPPLY DISCONNECT MAINS
1 Type code
2 Ordering number
3Specications
Illustration 3.1 Nameplate 1 and 2
1–6: Product Name
7: Overload H: Heavy duty
Q: Normal duty1)
8–10: Power size
0.37–75 kW. For example:
K37: 0.37 kW2)
1K1: 1.1 kW
11K: 11 kW
11–12: Voltage class T4: 380–480 V 3-phases
13–15: IP class E20: IP20
16–17: RFI H2: C3 Class
18: Brake chopper X: No
B: Built-in3)
19: LCP X: No
20: PCB coating C: 3C3
21: Mains terminals D: Load sharing
29–30: Embedded
eldbus
AX: No
A0: PROFIBUS
AL: PROFINET
Table 3.1 Type Code: Selection of Dierent Features and Options
For options and accessories, refer to the section Options and
Accessories in the FC 360 Design Guide.
1) Only 11–75 kW for normal duty variants. PROFIBUS and PROFINET
unavailable for normal duty.
2) For all power sizes, see chapter 8.1.1 Mains Supply 3x380–480 V
AC.
3) 0.37–22 kW with built-in brake chopper. 30–75 kW with external
brake chopper only.
130BC437.10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
F C - 3 6 0 H T 4 E 2 0 H 2 X X C D X X S X X X X A X B X
Q B 0
L
A
A
Illustration 3.2 Type Code String
Quick Start Quick Guide
MG06A602 Danfoss A/S © 04/2015 All rights reserved. 9
33

3.2 Hand On/Auto On Mode
After installation (see chapter 4 Installation), there are 2
simple ways to start up the frequency converter: Hand On
and Auto On mode. At the rst power-up, it is in Auto On
mode.
130BD062.10
DHand
On Reset
Auto
On
OK
On
Warn
Alarm
Illustration 3.3 Location of Hand On, O/Reset and Auto On
Keys on the NLCP
•Press [Hand On] to provide a local start command
to the frequency converter. Press [▲] and [▼] to
increase and decrease speed.
•Press [O/Reset] to stop the frequency converter.
•Press [Auto On] to control the frequency
converter either via control terminals or serial
communication.
CAUTION
Since the frequency converter is in Auto On mode at rst
power-up, the frequency converter may start the motor
directly.
NOTICE
Parameter 5-12 Terminal 27 Digital Input has coast inverse
as default setting. Connect terminals 12 and 27 to test
Hand On/Auto On running.
For LCP operation, see chapter 5 Local Control Panel and
Programming.
3.3 Application Selections
Use the selections for quick application set-up of the most
common applications by setting parameter 0-16 Application
Selection. When necessary, the selections can be modied
for individual needs. All selections are for Auto On mode.
NOTICE
When an application is selected, relevant parameters are
automatically set. Customer-specic conguration of all
parameters based on specic requirements is still
possible.
NOTICE
If any of the applications are selected, relay 1 is set to
[Running] and relay 2 is set to [Alarm]
Application
Pumps, fans, compressors
Description
For applications where a value (for example, pressure,
temperature) must be kept at a desired level by sensor feedback
130BC430.10
+24V 12
DI1 18
DI2 19
DI3 27
DI4 29
DI5 32
DI6 33
DI7 31
COM 20
+10V 50
AI1 53
-+
AI2 54
COM 55
AO1 45
AO2 42
1
2
3
4
5
6
R1
R2
FC 360
Start
Coast inverse
Jog
4-20
mA
Parameter settings
Parameter Option/value
Parameter 1-00 Conguration Mode [3] Process Closed
Loop
Parameter 1-03 Torque Characteristics [1] Variable Torque
Parameter 3-00 Reference Range [0] Min- Max
Parameter 3-15 Reference 1 Source [0] No Function
Parameter 4-12 Motor Speed Low Limit [Hz] 30.0 Hz
Parameter 4-14 Motor Speed High Limit
[Hz]
50.0 Hz
Parameter 5-10 Terminal 18 Digital Input [8] Start
Parameter 5-12 Terminal 27 Digital Input [2] Coast Inverse
Parameter 5-14 Terminal 32 Digital Input [14] Jog
Parameter 5-40 Function Relay
(Relay 1 Selection)
[5] Running
Parameter 5-40 Function Relay
(Relay 2 Selection)
[9] Alarm
Parameter 6-22 Terminal 54 Low Current 4.0 mA
Parameter 6-23 Terminal 54 High Current 20.0 mA
Parameter 6-29 Terminal 54 mode [0] Current Mode
Parameter 6-70 Terminal 45 Mode [0] 0–20 mA
Quick Start VLT®AutomationDrive FC 360
10 Danfoss A/S © 04/2015 All rights reserved. MG06A602
33

Parameter 6-71 Terminal 45 Analog Output [100] Output
frequency
Parameter 6-90 Terminal 42 Mode [0] 0–20 mA
Parameter 6-91 Terminal 42 Analog Output [103] Motor Current
Parameter 7-20 Process CL Feedback 1
Resource
[2] Analog input 54
Table 3.2 Process Closed Loop
Application
Local/remote
Description
For applications where the speed reference can be switched
between local potentiometer and remote current signal
130BC431.10
+24V 12
DI1 18
DI2 19
DI3 27
DI4 29
DI5 32
DI6 33
DI7 31
COM 20
+10V 50
AI1 53
-
+
AI2 54
COM 55
AO1 45
AO2 42
1
2
3
4
5
6
R1
R2
FC 360
Start
Coast inverse
Setup select
4-20
mA
Parameter settings Set-up 1 Set-up 2
Parameter 0-10 Active Set-
up
[9] Multi Set-up [9] Multi Set-up
Parameter 0-12 Link Setups [20] Linked [20] Linked
Parameter 1-00 Congu-
ration Mode
[0] Speed Open Loop [0] Speed Open
Loop
Parameter 3-00 Reference
Range
[0] Min–Max [0] Min–Max
Parameter 3-15 Reference 1
Source
[1] AI 53 [2] AI 54
Parameter 3-16 Reference 2
Source
Parameter 4-12 Motor
Speed Low Limit [Hz]
25.0 Hz 25.0 Hz
Parameter 4-14 Motor
Speed High Limit [Hz]
50.0 Hz 50.0 Hz
Parameter 5-10 Terminal 18
Digital Input
[8] Start [8] Start
Parameter 5-12 Terminal 27
Digital Input
[2] Coast Inverse [2] Coast
Inverse
Parameter 5-14 Terminal 32
Digital Input
[23] Set-up select [23] Set-up
select
Parameter 5-40 Function
Relay (Relay 1 Selection)
[5] Running [5] Running
Parameter 5-40 Function
Relay (Relay 2 Selection)
[9] Alarm [9] Alarm
Parameter 6-10 Terminal 53
Low Voltage
0.07 V
Parameter 6-11 Terminal 53
High Voltage
10 V
Parameter 6-19 Terminal 53
mode
[1] Voltage Mode
Parameter 6-22 Terminal 54
Low Current
4.0 mA
Parameter 6-23 Terminal 54
High Current
20.0 mA
Parameter 6-29 Terminal 54
mode
[0] Current
Mode
Parameter 6-70 Terminal 45
Mode
[0] 0–20 mA [0] 0–20 mA
Parameter 6-71 Terminal 45
Analog Output
[100] Output
frequency
[100] Output
frequency
Parameter 6-90 Terminal 42
Mode
[0] 0–20 mA [0] 0–20 mA
Parameter 6-91 Terminal 42
Analog Output
[103] Motor Current [103] Motor
Current
Table 3.3 Local/Remote
Quick Start Quick Guide
MG06A602 Danfoss A/S © 04/2015 All rights reserved. 11
33

Application
Conveyors, extruders
Description
For running at a stable speed by a voltage reference signal.
130BC432.10
+24V 12
DI1 18
DI2 19
DI3 27
DI4 29
DI5 32
DI6 33
DI7 31
COM 20
+10V 50
AI1 53
AI2 54
COM 55
AO1 45
AO2 42
1
2
3
4
5
6
R1
R2
FC 360
Start
Coast inverse
Parameter settings
Parameter Option/value
Parameter 1-00 Conguration Mode [0] Speed Open Loop
Parameter 3-00 Reference Range [0] Min–Max
Parameter 3-15 Reference 1 Source [1] AI 53
Parameter 4-12 Motor Speed Low Limit
[Hz]
25.0 Hz
Parameter 4-14 Motor Speed High Limit
[Hz]
50.0 Hz
Parameter 5-10 Terminal 18 Digital Input [8] Start
Parameter 5-12 Terminal 27 Digital Input [2] Coast Inverse
Parameter 5-40 Function Relay (Relay 1
Selection)
[5] Running
Parameter 5-40 Function Relay (Relay 2
Selection)
[9] Alarm
Parameter 6-10 Terminal 53 Low Voltage 0.07 V
Parameter 6-11 Terminal 53 High Voltage 10 V
Parameter 6-19 Terminal 53 mode [1] Voltage Mode
Parameter 6-70 Terminal 45 Mode [0] 0–20 mA
Parameter 6-71 Terminal 45 Analog
Output
[100] Output frequency
Parameter 6-90 Terminal 42 Mode [0] 0–20 mA
Parameter 6-91 Terminal 42 Analog
Output
[103] Motor Current
Table 3.4 Speed Open Loop
Application
Machine tools, texturizers
Description
For precise speed applications with 24 V encoder feedback
130BC433.12
+24 V 12
DI1 18
DI2 19
DI3 27
DI4 29
DI5 32
DI6 33
DI7 31
COM 20
50
AI1 53
AI2 54
COM 55
AO1 45
AO2 42
1
2
3
4
5
6
R1
R2
FC 360
Start
Coast inverse
+10 V
B
A
Parameter settings
Parameter Option/value
Parameter 1-00 Conguration Mode [1] Speed Close Loop
Parameter 3-00 Reference Range [0] Min–Max
Parameter 3-15 Reference 1 Source [1] AI 53
Parameter 3-16 Reference 2 Source [11] Local Bus Ref
Parameter 4-12 Motor Speed Low Limit
[Hz]
20.0 Hz
Parameter 4-14 Motor Speed High Limit
[Hz]
50.0 Hz
Parameter 5-10 Terminal 18 Digital Input [8] Start
Parameter 5-12 Terminal 27 Digital Input [2] Coast Inverse
Parameter 5-14 Terminal 32 Digital Input [82] Encoder input B
Parameter 5-15 Terminal 33 Digital Input [81] Encoder input A
Parameter 5-40 Function Relay (Relay 1
Selection)
[5] Running
Parameter 5-40 Function Relay (Relay 2
Selection)
[9] Alarm
Parameter 6-10 Terminal 53 Low Voltage 0.07 V
Parameter 6-11 Terminal 53 High Voltage 10 V
Parameter 6-19 Terminal 53 mode [1] Voltage Mode
Parameter 6-70 Terminal 45 Mode [0] 0–20 mA
Parameter 6-71 Terminal 45 Analog
Output
[100] Output frequency
Parameter 6-90 Terminal 42 Mode [0] 0–20 mA
Parameter 6-91 Terminal 42 Analog
Output
[103] Motor Current
Quick Start VLT®AutomationDrive FC 360
12 Danfoss A/S © 04/2015 All rights reserved. MG06A602
33

Parameter 7-00 Speed PID Feedback
Source
[1] 24 V encoder
Table 3.5 Speed Close Loop
Application
Industrial washing machines, conveyors
Description
For applications with 8 dierent speeds by digital input. By using
another digital input, 16 speeds are possible.
130BC434.10
+24V 12
DI1 18
DI2 19
DI3 27
DI4 29
DI5 32
DI6 33
DI7 31
COM 20
+10V 50
AI1 53
AI2 54
COM 55
AO1 45
AO2 42
1
2
3
4
5
6
R1
R2
FC 360
Start
Coast inverse
Pre set ref bit 0
Pre set ref bit 1
Pre set ref bit 2
Parameter settings
Parameter Option/value
Parameter 1-00 Conguration Mode [0] Speed Open Loop
Parameter 3-00 Reference Range [0] Min–Max
Parameter 3-15 Reference 1 Source [0] No Function
Parameter 4-14 Motor Speed High Limit
[Hz]
50.0 Hz
Parameter 5-10 Terminal 18 Digital Input [8] Start
Parameter 5-12 Terminal 27 Digital Input [2] Coast Inverse
Parameter 5-13 Terminal 29 Digital Input [16] Preset ref bit 0
Parameter 5-14 Terminal 32 Digital Input [17] Preset ref bit 1
Parameter 5-15 Terminal 33 Digital Input [18] Preset ref bit 2
Parameter 6-70 Terminal 45 Mode [0] 0–20 mA
Parameter 6-71 Terminal 45 Analog
Output
[100] Output frequency
Parameter 6-90 Terminal 42 Mode [0] 0–20 mA
Parameter 6-91 Terminal 42 Analog
Output
[103] Motor Current
Table 3.6 Multi-speed
Application
One Gear Drive (OGD)
Description
For applications that use OGD. For example, conveyors in food
and beverage industries.
+24V 12
DI1 18
DI2 19
DI3 27
DI4 29
DI5 32
DI6 33
DI7 31
COM 20
+10V 50
AI1 53 -
+
AI2 54
COM 55
AO1 45
AO2 42
1
2
3
4
5
6
R1
R2
FC 360
Start
Coast inverse
4-20
mA
130BD898.10
Parameter settings
Parameter Option/value
Parameter 1-00 Conguration Mode [0] Open Loop
Parameter 1-01 Motor Control Principle [1] VVC+
Parameter 1-08 Motor Control Bandwidth high
Parameter 1-10 Motor Construction [1] PM, non-salient SPM
Parameter 1-14 Damping Gain 120
Parameter 1-15 Low Speed Filter Time
Const.
0.175
Parameter 1-16 High Speed Filter Time
Const.
0.175
Parameter 1-17 Voltage lter time const. 0.035
Parameter 1-24 Motor Current 7.2
Parameter 1-25 Motor Nominal Speed 3000
Parameter 1-26 Motor Cont. Rated Torque 12.6
Parameter 1-29 Automatic Motor
Adaptation (AMA)
[0] O
Parameter 1-30 Stator Resistance (Rs) 0.5
Parameter 1-37 d-axis Inductance (Ld) 5
Parameter 1-39 Motor Poles 10
Parameter 1-40 Back EMF at 1000 RPM 120
Parameter 1-42 Motor Cable Length 50 m
Parameter 1-66 Min. Current at Low Speed 50
Parameter 1-73 Flying Start [2] Enable always
Parameter 2-06 Parking Current 80
Parameter 2-07 Parking Time 0.5
Quick Start Quick Guide
MG06A602 Danfoss A/S © 04/2015 All rights reserved. 13
33

Parameter 2-10 Brake Function [0] O
Parameter 3-03 Maximum Reference 250 Hz
Parameter 4-14 Motor Speed High Limit
[Hz]
250 Hz
Parameter 4-16 Torque Limit Motor Mode 160
Parameter 4-18 Current Limit 160
Parameter 5-10 Terminal 18 Digital Input [8] Start
Parameter 5-11 Terminal 19 Digital Input [0] No operation
Parameter 5-12 Terminal 27 Digital Input [2] Coast inverse
Parameter 5-13 Terminal 29 Digital Input [0] No operation
Parameter 5-14 Terminal 32 Digital Input [0] No operation
Parameter 5-15 Terminal 33 Digital Input [0] No operation
Parameter 5-16 Terminal 31 Digital Input [0] No operation
Parameter 6-10 Terminal 53 Low Voltage 4.0 mA
Parameter 6-11 Terminal 53 High Voltage 20.0 mA
Parameter 6-14 Terminal 53 Low Ref./
Feedb. Value
0
Parameter 6-15 Terminal 53 High Ref./
Feedb. Value
250
Parameter 6-19 Terminal 53 mode [0] Current Mode
Parameter 14-01 Switching Frequency 10.0 kHz
Parameter 14-07 Dead Time Compen-
sation Level
65
Parameter 14-64 Dead Time Compen-
sation Zero Current Level
[0] Disabled
Parameter 14-65 Speed Derate Dead Time
Compensation
250
Parameter 14-51 DC-Link Voltage Compen-
sation
[0] O
Parameter 30-20 High Starting Torque
Time [s]
0
Parameter 30-21 High Starting Torque
Current [%]
100
Parameter 30-22 Locked Rotor Protection [0] O
Parameter 30-23 Locked Rotor Detection
Time [s]
1
Table 3.7 One Gear Drive (OGD)
For further examples, refer to chapter 6 Application
Examples.
3.4 Jumper Terminal 12 and 27
When the factory default programming values are used,
connect a jumper wire between terminal 12 and terminal
27 for the frequency converter to operate.
•Digital input terminal 27 is designed to receive a
24 V DC external interlock command. In many
applications, wire an external interlock device to
terminal 27.
•When no interlock device is used, wire a jumper
between control terminal 12 and terminal 27. This
provides internal 24 V signal on terminal 27.
•No signal present prevents the unit from
operating.
3.5 Automatic Motor Adaptation (AMA)
Automatic motor adaptation (AMA)
It is highly recommended to run AMA because it measures
the electrical characteristics of the motor to optimise
compatibility between the frequency converter and the
motor under VVC+mode.
•The frequency converter builds a mathematical
model of the motor for regulating output motor
current, thus enhancing motor performance.
•Some motors are unable to run the complete
version of the test. In that case, select Enable
reduced AMA.
•If warnings or alarms occur, see
chapter 7.3 Warning and Alarm Code List.
•Run this procedure on a cold motor for best
results.
To run AMA using the numeric LCP
1. By default parameter setting, connect terminals
12 and 27 before running AMA.
2. Enter the Main Menu.
3. Go to parameter group 1-** Load and Motor.
4. Press [OK].
5. Set motor parameters using nameplate data for
parameter group 1-2* Motor Data.
6. Set motor cable length in parameter 1-42 Motor
Cable Length
7. Go to parameter 1-29 Automatic Motor Adaptation
(AMA).
8. Press [OK].
9. Select [1] Enable complete AMA.
10. Press [OK].
11. The test runs automatically and indicates when it
is complete.
Depending on the power size, the AMA takes 3–10
minutes to complete.
NOTICE
The AMA function in FC 360 does not cause the motor to
run, and it does not harm the motor.
Quick Start VLT®AutomationDrive FC 360
14 Danfoss A/S © 04/2015 All rights reserved. MG06A602
33

4 Installation
4.1 Mechanical Installation
Select the best possible operation site by considering:
•Ambient operating temperature.
•Installation method.
•Cooling.
•Position of the frequency converter.
•Cable routing.
•Power source supplying correct voltage and
necessary current.
•Motor current rating within the maximum current
from the frequency converter.
•Correct rating of external fuses and circuit
breakers.
Cooling and Mounting:
•Provide top and bottom clearance for air cooling,
see Table 4.1 for clearance requirements.
•Consider derating for temperatures starting from
45 °C and elevation 1000 m above sea level. See
the design guide for details on derating.
Enclosure size J1–J5 J6 and J7
Clearance above and below the
unit [mm] 100 200
Table 4.1 Minimum Airow Clearance Requirements
•Mount the unit vertically.
•IP20 units allow side-by-side installation.
•Improper mounting can result in overheating and
reduced performance.
•Use the slotted mounting holes on the unit for
wall mounting, when provided.
•See chapter 8.4 Connection Tightening Torques for
proper tightening specications.
Installation Quick Guide
MG06A602 Danfoss A/S © 04/2015 All rights reserved. 15
44

4.2 Electrical Installation
This section describes how to wire the frequency converter.
130BC438.15
3 Phase
power
input
Switch Mode
Power Supply
Motor
Analog Output
Interface
(PNP) = Source
(NPN) = Sink
ON=Terminated
OFF=Open
Brake
resistor
91 (L1)
92 (L2)
93 (L3)
PE
50 (+10 V OUT)
53 (A IN)
54 (A IN)
55 (COM A IN)
0/4-20 mA
12 (+24 V OUT)
31 (D IN)
18 (D IN)
20 (COM D IN)
10 V DC
15 mA 100 mA
+ - + -
(U) 96
(V) 97
(W) 98
(PE) 99
(A OUT) 45
(A OUT) 42
(P RS-485) 68
(N RS-485) 69
(COM RS-485) 61
0V
5V
S801
0/4-20 mA
RS-485
RS-485
03
+10 V DC
0/4-20 mA
0-10 V DC
24 V DC
02
01
05
04
240 V AC, 3 A
24 V (NPN)
0 V (PNP)
0 V (PNP)
24 V (NPN)
19 (D IN)
24 V (NPN)
0 V (PNP)
27 (D IN/OUT)
24 V
0 V
0 V (PNP)
24 V (NPN)
0 V
24 V
29 (D IN/OUT)
24 V (NPN)
0 V (PNP)
0 V (PNP)
24 V (NPN)
33 (D IN)
32 (D IN)
95
P 5-00
21
ON
(+UDC) 89
(BR) 81 5)
24 V (NPN)
0 V (PNP)
0-10 V DC
(-UDC) 88
RFI
3)
0 V
240 V AC, 3 A
Relay 1
1)
Relay 2 2)
4)
06
Illustration 4.1 Basic Wiring Schematic Drawing
A=Analog, D=Digital
1) Built-in brake chopper available from 0.37–22 kW.
2) Relay 2 is 2-pole for J1–J3 and 3-pole for J4–J7. Relay 2 of J4–J7 with terminals 4, 5, and 6 has the same NO/NC logic as relay
1. Relays are pluggable in J1–J5, and xed in J6–J7.
3) Single DC choke in 0.37–22 kW (J1–J5); Dual DC choke in 30–75 kW (J6–J7).
4) Switch S801 (bus terminal) can be used to enable termination on the RS485 port (terminals 68 and 69).
5) No BR for 30–75 kW (J6–J7).
Installation VLT®AutomationDrive FC 360
16 Danfoss A/S © 04/2015 All rights reserved. MG06A602
44

130BD391.11
1
2
3
4
5
6
78
910
Reset Auto
On
Hand
On
OK
Back
Menu
Status Quick
Menu
Main
Menu
PE
U
V
W
L1
L2
L3
PE
1 PLC 6 Minimum 200 mm (7.9 inch) between control cables, motor, and
mains
2 Frequency converter 7 Motor, 3-phase and PE
3 Output contactor (not recommended) 8 Mains, 3-phase and reinforced PE
4 Grounding rail (PE) 9 Control wiring
5 Cable shielding (stripped) 10 Equalising minimum 16 mm2(6 AWG)
Illustration 4.2 Typical Electrical Connection
Installation Quick Guide
MG06A602 Danfoss A/S © 04/2015 All rights reserved. 17
44

4.2.1 General Requirements
WARNING
EQUIPMENT HAZARD!
Rotating shafts and electrical equipment can be
hazardous. It is important to protect against electrical
hazards when applying power to the unit. All electrical
work must conform to national and local electrical codes.
Installation, start up, and maintenance must be
performed only by trained and qualied personnel.
Failure to follow these guidelines could result in death or
serious injury.
CAUTION
WIRING ISOLATION!
Run input power, motor wiring, and control wiring in 3
separate metallic conduits or use separated screened
cable for high frequency noise isolation. Failure to isolate
power, motor, and control wiring could result in less than
optimum frequency converter and associated equipment
performance.
Run motor cables from multiple frequency converters
separately. Induced voltage from output motor cables
run together can charge equipment capacitors even with
the equipment turned o and locked out.
•An electronically activated function within the
frequency converter provides overload protection
for the motor. The overload provides Class 20
motor overload protection.
Wire type and ratings
•All wiring must comply with local and national
regulations regarding cross-section and ambient
temperature requirements.
•Danfoss recommends that all power connections
be made with a minimum 75 °C rated copper
wire.
•See chapter 8 Specications for recommended
wire sizes.
4.2.2 Grounding Requirements
WARNING
GROUNDING HAZARD!
For operator safety, a certied electrical installer should
ground the frequency converter in accordance with
national and local electrical codes as well as instructions
contained within this manual. Ground currents are higher
than 3.5 mA. Failure to ground the frequency converter
properly could result in death or serious injury.
•Establish proper protective grounding for
equipment with ground currents higher than 3.5
mA must be established.
•A dedicated ground wire is required for input
power, motor power, and control wiring.
•Use the clamps provided with the equipment for
proper ground connections.
•Do not ground 1 frequency converter to another
in a daisy chain fashion (see Illustration 4.3).
•Keep the ground wire connections as short as
possible.
•Use high-strand wire to reduce electrical noise.
•Follow motor manufacturer wiring requirements.
130BC500.10
FC 1
FC 1
FC 2
FC 2
FC 3
FC 3
PE
PE
Illustration 4.3 Grounding Principle
4.2.3 Mains, Motor, and Ground
Connections
WARNING
INDUCED VOLTAGE!
Run output motor cables from multiple frequency
converters separately. Induced voltage from output
motor cables run together can charge equipment
capacitors even when the equipment is turned o and
locked out. Failure to run output motor cables separately
could result in death or serious injury.
Grounding clamps are provided for motor wiring (see
Illustration 4.4).
Installation VLT®AutomationDrive FC 360
18 Danfoss A/S © 04/2015 All rights reserved. MG06A602
44