DANHAG APP-control User manual
APP - Control
Version v10.x
as of 02.2018
Operating manual
Front view
Antenna
Status LED
Release
SIM card
SMA
connection
Rear view
Release
(connector I)
PIN1
PIN8
GPS LED
Release
(connector II)
Table of content
1 Scope of delivery.............................................................................................
2 Safety instructions........................................................................................... 6
3 Intended use................................................................................................... 6
4 Obligation and liability....................................................................................7
Malfunction..................................................................................................... 8
6 Disposal........................................................................................................... 8
7 Declaration of conformity............................................................................... 8
7.1 Typengenehmigung..............................................................................8
8 Device description...........................................................................................9
8.1 Difference BASIC / W-BUS / E-BUS........................................................9
8.2 Alarm function...................................................................................11
8.3 Switching acknowledgment................................................................12
8.4 Status LED, GPS LED............................................................................12
9 SIM-card........................................................................................................ 13
9.1 Inserting the SIM card........................................................................ 13
10 Inputs and Outputs (connector I)................................................................14
11 electrical connection................................................................................... 16
11.1 connection to the heater..................................................................16
11.2 Connection of ext. button.................................................................17
12 Accessories connection...............................................................................18
12.1 External temperature sensor............................................................18
12.2 GPS-receiver..................................................................................... 18
13 Start up....................................................................................................... 20
14 Configuration.............................................................................................. 21
14.1 Table parameter ..............................................................................24
14.2 Configuration with SMS configurator................................................2
14.3 Configuration with mobile phone ....................................................2
14.4 Delete a phone number ...................................................................2
14. Reset................................................................................................ 2
14.6 SMS-commands................................................................................26
1 Trouble shooting......................................................................................... 28
16 Manufacturer.............................................................................................. 29
17 technical data.............................................................................................. 29
18 Copyright..................................................................................................... 29
19 Installation location..................................................................................... 30
APP-control v10.x
1 cope of delivery
•APP-control
•GSM-antenna (straight)
•connection line (14-pole connector)
•operating manual
optional available accessories
•vehicle-specific cable harnesses
•indoor window antenna
•Antenna adapter (FME to SMA)
•GPS-receiver
•external temperature sensor
- 32
Prior to insertion of the SIM card please deactivate the PIN
request and the mailbox and delete all telephone numbers
that may be stored.
The operation of the GSM remote control will require any
SIM card which is not included in the scope of delivery.
APP-control v10.x
2 afety instructions
Prior to the commissioning ot the device please read this operating manual
completely. Additionally you have to observe the generally valid and the local
regulations for accident prevention and environmental protection. Keep the
operating manual. Do not operate the device in a surrounding where
flammable gases, vapors, liquids or dust are existing or my exist.
3 Intended use
The APP-control allows the switching of any device per APP, SMS or call. The
APP-control is designated for private use and not for commercial purposes. The
APP-control has to be used exclusively according to the instructions of thes
operating manual. The manufacturer is not liable for damage which are caused
by inappropriate use or incorrect operation.
6 - 32
Do not use the APP-control if due to a malfunction danger
and / or damage may occur.
The installation must only be carried out by a qualified
technican.
APP-control v10.x
4 Obligation and liability
The APP-control has been developed and manufactured according to the
current technical status and the recognized safety rules. It cannot be assured,
however, that the APP-control will operate as intended under all circumstances,
at any time and under all conditions.
The DANHAG APP-control is manufactures in compliance with the EU directive
2011/6 /EG (RoHS 2). this directive determines the use of hazardous material
in devices and components.
The compliance with the prescribed EMC limit values was confirmed by an
independent EMC testing laboratory.
Our products are recorded in the register for waste electrical equipment and
meet the requirements of the relevant, applicable CE regulations. We confirm
the observation of European standards on our devices by the CE marking. WEEE
Reg. No.: DE 33181931
We only use sales packaging licensed by the disposal company
“Zentek duales System”.
7 - 32
Do not use the APP-control for the switching of life-
support systems or devices with an emanating danger due
to an uncontrolled switching on and off.
APP-control v10.x
5 Malfunction
The APP-control must taken out of service immediately when it might be
assumed that a safe operation cannot be guaranteed any more. All appropriate
measures must be taken to exclude an unintentional re-commissioning. Only a
qualified person os allowed to perform a repair.
6 Disposal
This product must be taken to an official collecting point for disposal. You can
also give back the product to the manufacturer for ecological disposal.
7 Declaration of conformity
The device is complying with the EU regulation 2004/108/EG (electromagnetic
compatibility). Applied standards: EN 0498 / 2011
7.1 Typengenehmigung
8 - 32
E1 10R - 058021
This product must kept out from the domestic waste.
Please dispose the product according to the applicable
legal provisions only.
APP-control v10.x
8 Device description
8.1 Difference BA IC / W-BU / E-BU
The versions are supporting different output signals as shown at the table.
output signal / Version output
BA IC W-BU E-BU PIN
+12V +12V +12V 2
ground ground ground 3
+12V W-BUS 3 E-BUS 3 1
W-BUS 4 E-BUS 4
W-BUS E-BUS
W-BUS 6 E-BUS 6
E-BUS 7
E-BUS 8
9 - 32
The APP-control "W-BUS" and "E-BUS" are supporting
different output signals. An overview about the signal
needed for your vehicle or heater
can be found at our website: www.danhag.de
APP-control v10.x
8.1.1 tatus
You can query the current status of the heater by sending a sms with the text
"INFO" to the APP-control.
BA IC, W-BU
The status displays the state of the APP-control.
E-BU
The E-BUS version communicates with the heater and can display the current
state of the heater.
8.1.2 tatus messages
E-BU only
Status messages are deactivated with the default settings.
When status messages are enabled, you will be notified via SMS either when:
•the heater was started successfully
•the heater could not be started
•the heater was turned off
10 - 32
Status messages are not supported from all vehicles /
heaters.
Table of contents
