DAQ system USB3-FRM22 User manual

USB3-FRM22
User Manual
Version 1.0
ⓒ2005 DAQ SYSTEM Co., Ltd. All rights reserved.
Microsoft®is a registered trademark; Windows®, Windows NT®, Windows XP®, Windows 7®, Windows 8®, Windows 10®
All other trademarks or intellectual property mentioned herein belongs to their respective owners.
Information furnished by DAQ SYSTEM is believed to be accurate and reliable, However, no responsibility is assumed by DAQ SYSTEM for its use, nor
for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under
any patent or copyrights of DAQ SYSTEM.
The information in this document is subject to change without notice and no part of this document may e copied or reproduced without the prior
written consent.

USB3-FRM22 User’s Manual
1
Contents
1. Introduction
1-1. Product Specification ------------------------------------------------------------------------ 2
1-2. Product Application ------------------------------------------------------------------------ 3
2. USB3-FRM22 Description
2-1. Layout ------------------------------------------------------------------------ 4
2-2. Board Description ------------------------------------------------------------------------ 5
2-3. I/O Terminal Pin Map ------------------------------------------------------------------------ 6
(1) CN1 Connector ------------------------------------------------------------------------ 6
(2) J1 Connector ------------------------------------------------------------------------ 6
(3) J2 Connector ------------------------------------------------------------------------ 8
(4) J6 Connector ------------------------------------------------------------------------ 8
(5) J10 Connector ------------------------------------------------------------------------ 8
(6) J11 Connector ------------------------------------------------------------------------ 9
(7) J12 Connector ------------------------------------------------------------------------ 10
(8) J13 Connector ------------------------------------------------------------------------ 11
(9) J14 Connector ------------------------------------------------------------------------ 11
(10) J15 Connector ------------------------------------------------------------------------ 12
(11) SW1 Switch ------------------------------------------------------------------------- 13
(12) SW3 Switch ------------------------------------------------------------------------ 13
2-4. Board Size ------------------------------------------------------------------------ 14
3. Sample Program ------------------------------------------------------------------------ 15
3-1. Description of Image Frame Functions ------------------------------------------------------- 16
3-2. Description of Clock Functions ---------------------------------------------------------------- 20
3-3. Description of Power/Digital I/O Functions -------------------------------------------------- 21
3-4. Description of I2C Read/Write Functions ---------------------------------------------------- 22
3-5. Description of Misc. Functions --------------------------------------------------------------- 23
3-6. Description of Status Functions --------------------------------------------------------------- 24
Appendix
A-1. Repair Regulations -------------------------------------------------------------------------- 25

USB3-FRM22 User’s Manual
2
1. Introduction
1-1. Product Specification
Item
Description
Remark
Hardware
PC Interface
USB3.0
B-Type
Operation Power
+12VDC/650mA
External 12V DC Power
(A6-Type : 5.5x2.1mm)
Video Interface
MIPI CSI C-PHY 3 Lane
MIPI CSI D-PHY 4 Lane
D-PHY Virtual Mode
2.2 ~ 2.3 Gsym / 1 Lane
2.5Gbps / 1 Lane
I/O Terminal No.
Sensor GPIO 4bit
General GPIO 12bit
User GPIO 12bit
3.3V GPIO 4bit, User GPIO
8bit
On-board Memory
256MB (DDR3) x2
Communication
I2C/SPI
Simultaneously Use
Max. 4
Software
OS
Windows 2000/XP/7/8/10 (32/64bit)
API
Windows Client DLL API
Development
Windows Application by User
Custom USB Device Firmware
Custom Windows Client DLL
Support
Sample Program
VC++ (Please contact for C#)
Environmental conditions
Operating temperature range
0 ~ 50℃
Use Heat Pad
Storage temperature range
-20 ~ 80℃
Humidity range
Non-condensing
Board Size
100mm X 80mm
PCB Board Size

USB3-FRM22 User’s Manual
3
1-2. Product Application
- Frame Grabber
- Test for Variable MIPI Sensor
The USB3-FRM22 board transmits the C-PHY or D-PHY MIPI (Mobile Industry Processor
Interface) signal of the sensor board to the PC in the USB3.0 Super Speed (5Gbps) method. Two
signals of C-PHY or D-PHY can be selected and used. The received signal is processed by the
software (application) provided by the DAC system in the PC and displayed as an image.
[Figure 1-1] shows an example of using the input board.
MIPI SENSOR
C-PHY or D-PHY
[Figure 1-1. USB3-FRM22 Example Using]

USB3-FRM22 User’s Manual
4
2. USB3-FRM22 Description
2-1. Layout
USB3-FRM22 Board
USB3-FRM22
Rev. A
U12
J2
CN1
U9
D9
D10
D12
D11
REF1 REF2
123 789 123 789
A
C
E
G
J
L
N
R
A
C
E
G
J
L
N
R
U10
J9
ON
1 2
SW3
U5
U11
U13
D7
J1
U9
U14
SW1
U7
J11
J3
U4
U2
J8
J6
J7
1
13
34
47
78
8
5
56
6
2
2
SW4
J15 J12
J10
J14 J13
D14
[Figure 2-1. USB3-FRM22 Components Layout]
There are 6 important LEDs on the board, and the description of each is as follows.
D7 : Lights up when the board is configured and ready for operation.
D9 : Lights up when connected via USB3.0 (blinks).
D10 : The Vertical Synchronization signal line (Vsync) is connected.
This is a mark to visually check Vsync.
D11 : The Horizontal Synchronization signal line (Hsync) is connected.
This is a mark to visually check Hsync.
D12 : Displays Vertical Synchronization (Vsync) divided by 1/16.
This is a mark to visually check Vsync.
D14 :Lights up when 3.3V power is applied.

USB3-FRM22 User’s Manual
5
2-2. Board Description
As shown in the figure below, in the case of USB3-FRM22, the overall control is in charge of
FPGA Core Logic. Its main function is to transmit C-PHY or D-PHY MIPI Image Frame Data signals
through the External I/O connector. These functions are performed using API in PC through USB
3.0 interface.
External I/O connector uses 2x20 2.54mm Pitch Male Header connector to connect to MIPI
sensor board connector, and 2x16 2.54mm Pitch Male Header connector (J4, J5) to connect with
our MIPI-PWR02 power board. For detailed connector signal specifications, refer to Section 2.3
and Appendix A1.
[Figure 2-2. USB3-FRM22 Block Diagram]
The program of the FPGA core logic uses JTAG, and functions to save the logic program in
the FPGA Program Logic and download it when power is applied.
Note) In case of USB connection, USB2.0 interface, which is insufficient for high-speed
image transfer, is not supported. Only the USB3.0 interface is used.

USB3-FRM22 User’s Manual
6
2-3. I/O Terminal Pin Map
(1) CN1 Connector
When the PIN of the USB3.0 Standard Powered-B type connector of the board is viewed from
the front where the cable is connected, it is as shown in [Figure 2-3].
USB B type
Connector
12
3 4
10 11
56789
[Figure 2-3. CN1 Connector (USB3.0 Standard Powered-B type Front View)]
[Table 1. USB3.0 Standard Powered-B Connector]
No
Name
Description
Remark
1
VBus
+5V Power
+5V Power
2
USB D-
USB2.0 data (Negative)
USB2.0 Signals
3
USB D+
USB2.0 data (Positive)
USB2.0 Signals
4
GND
Ground for Power Return
USB Power GND
5
StdA_SSTX-
Super Speed Transmitter
(Negative)
USB3.0 Signals
6
StdA_SSTX+
Super Speed Transmitter
(Positive)
USB3.0 Signals
7
GND_DRAIN
Ground for Signal Return
USB Power GND
8
StdA_SSRX+
Super Speed Receiver
(Positive)
USB3.0 Signals
9
StdA_SSRX-
Super Speed Receiver
(Negative)
USB3.0 Signals
10
DPWR
Power Provided by Device
USB Power GND
11
DGND
Ground return for DPWR
USB Power GND

USB3-FRM22 User’s Manual
7
(2) J1 Connector
It is connected to the MIPI SENSOR board and the signals are as follows.
1
2
3
4
95
68
7
10
11
12
13
142024
2321
22
19
18
17
16
15
26
25
27
28
29
303640
3937
38
35
34
33
32
31
[Figure 2-4. J1 Connector (Top View)]
[Table 2. J1 Connector Description]
No.
Name
Description
Remark
1
SP0
SENSOR Power
2
SP1
SENSOR Power
3
SP2
SENSOR Power
4
SP3
SENSOR Power
5
GND
Ground
6
GND
Ground
7
SCL
Serial Clock
8
C_L0_RXA or D_L0_RXP
C_lane0_RX_A or D_lane0_RX_P
C : C-Phy, D : D-Phy
9
SDA
Serial Data
10
C_L0_RXB or D_L0_RXN
C_lane0_RX_B or D_lane0_RX_N
C : C-Phy, D : D-Phy
11
GND
Ground
12
GND
Ground
13
ENB
Enable
14
C_L0_RXC or D_L1_RXP
C_lane0_RX_C or D_lane1_RX_P
C : C-Phy, D : D-Phy
15
S_RESET
Reset
16
C_L1_RXD or D_L1_RXN
C_lane1_RX_D or D_lane1_RX_N
C : C-Phy, D : D-Phy
17
GND
Ground
18
GND
Ground
19
CNT0
Sensor General Purpose IO0
Using SDIO_xxx
function
20
C_L2_RXA or D_L2_RXP
C_lane2_RX_A or D_lane2_RX_P
C : C-Phy, D : D-Phy
21
CNT1
Sensor General Purpose IO1
Using SDIO_xxx
function
22
C_L2_RXB or D_L2_RXN
C_lane2_RX_B or D_lane2_RX_N
C : C-Phy, D : D-Phy
23
GND
Ground
24
GND
Ground
25
CNT2
Sensor General Purpose IO2
Using SDIO_xxx
function
26
C_L2_RXC or D_L3_RXP
C_lane2_RX_C or D_lane3_RX_P
C : C-Phy, D : D-Phy

USB3-FRM22 User’s Manual
8
27
CNT3
Sensor General Purpose IO3
Using SDIO_xxx
function
28
C_L2_RXD or D_L3_RXN
C_lane2_RX_D or D_lane3_RX_N
C : C-Phy, D : D-Phy
29
GND
Ground
30
GND
Ground
31
GND
Ground
32
C_L1_RXA or D_CLK_RXP
C_lane1_RX_A or D_CLK_RX_P
C : C-Phy, D : D-Phy
33
GND
Ground
34
C_L1_RXB or D_CLK_RXN
C_lane1_RX_B or D_CLK_RX_N
C : C-Phy, D : D-Phy
35
MCLK
Master Clock
36
C_L1_RXC
C_lane2_RX_C
C : C-Phy,
37
GND
Ground
38
GND
Ground
39
SP4
SENSOR Power
40
SP5
SENSOR Power
(3) J2 Connector
It is a connector used as SPI (Serial Peripheral Interface).
[Figure 2-5. J5 Connecter (Top View)]
[Table 3. J2 Connecter Description]
No.
Name
Description
1
F_SPI_SCK
Serial Clock
2
F_SPI_SSN
Slave Select
3
F_SPI_MISO
Master Input, Slave Output
4
F_SPI_MOSI
Master Output, Slave Input
(4) J6 Connector
External input 12V power connector.

USB3-FRM22 User’s Manual
9
(5) J10 Connector
It is connected to the MIPI power board and is a connector related to sensor power and
some communication.
1
2
3
4
95
6 8
7
10
11
12
13
14 20
19
18
17
16
15
[Figure 2-5. J10 Connector (Top View)]
[Table 4. J10 Connector Description]
No.
Name
Description
Remark
1
GND
Ground
2
GND
Ground
3
SP0
SENSOR Power
0.9 ~ 4.1V
4
SP1
SENSOR Power
0.9 ~ 4.1V
5
SP2
SENSOR Power
0.9 ~ 4.1V
6
SP3
SENSOR Power
0.9 ~ 4.1V
7
GND
Ground
8
GND
Ground
9
SCL
Serial Clock
3.3V
10
SDA
Serial Data
3.3V
11
PWR_SCL
Power Serial Clock
3.3V
12
PWR_SDA
Power Serial Data
3.3V
13
AD_SCL
AD Converter Serial Clock
3.3V
14
AD_SDA
AD Converter Serial Data
3.3V
15
GND
Ground
16
GND
Ground
17
OS_SCL
Open/Short Serial Clock
3.3V
18
OS_SDA
Open/Short Serial Data
3.3V
19
GND
Ground
20
GND
Ground

USB3-FRM22 User’s Manual
10
(6) J11 Connector
It is connected to the MIPI power board, and is a connector related to sensor power, SPI
communication, and some GPIO (General Purpose In/Out).
1
2
3
4
95
6 8
7
10
11
12
13
14 20
19
18
17
16
15
[Figure 2-6. J11 Connector (Top View)]
[Table 5. J11 Connector Description]
No.
Name
Description
Remark
1
GND
Ground
2
GND
Ground
3
SP4
User Defined Power
0.9 ~ 4.1V
4
SP5
User Defined Power
0.9 ~ 4.1V
5
GND
Ground
6
GND
Ground
7
SPI_SCK
Serial Clock
3.3V
8
SPI_MOSI
Master Output, Slave Input
3.3V
9
SPI_EN
Slave Select
3.3V
10
SPI_MISO
Master Input, Slave Output
3.3V
11
5V_IN
5V Power
12
V_IO2
IO2 Power
13
GPIO0
General Purpose IO0
Using PWR_DIO_xxx function
14
GPIO1
General Purpose IO1
Using PWR_DIO_xxx function
15
GPIO2
General Purpose IO2
Using PWR_DIO_xxx function
16
GPIO3
General Purpose IO3
Using PWR_DIO_xxx function
17
GPIO4
General Purpose IO4
Using PWR_DIO_xxx function
18
GPIO5
General Purpose IO5
Using PWR_DIO_xxx function
19
GND
Ground
20
GND
Ground

USB3-FRM22 User’s Manual
11
(7) J12 Connector
It is connected to the MIPI power board and is a connector related to GPIO (General
Purpose In/Out).
1
2
3
4
95
6 8
7
10
11
12
13
14 20
19
18
17
16
15
[Figure 2-7. J12 Connector (Top View)]
[Table 6. J12 Connector Description]
No.
Name
Description
Remark
1
GND
Ground
2
GND
Ground
3
GPIO6
General Purpose IO6
Using PWR_DIO_xxx function
4
GPIO7
General Purpose IO7
Using PWR_DIO_xxx function
5
GND
Ground
6
GND
Ground
7
U3_GPIO0
User General Purpose IO0
Using DIO33_xxx function
8
U3_GPIO1
User General Purpose IO1
Using DIO33_xxx function
9
U3_GPIO2
User General Purpose IO2
Using DIO33_xxx function
10
U3_GPIO3
User General Purpose IO3
Using DIO33_xxx function
11
U_GPIO0
User General Purpose IO0
Using DIO_xxx function
12
U_GPIO1
User General Purpose IO1
Using DIO_xxx function
13
U_GPIO2
User General Purpose IO2
Using DIO_xxx function
14
U_GPIO3
User General Purpose IO3
Using DIO_xxx function
15
U_GPIO4
User General Purpose IO4
Using DIO_xxx function
16
U_GPIO5
User General Purpose IO5
Using DIO_xxx function
17
U_GPIO6
User General Purpose IO6
Using DIO_xxx function
18
U_GPIO7
User General Purpose IO7
Using DIO_xxx function
19
GND
Ground
20
GND
Ground

USB3-FRM22 User’s Manual
12
(8) J13 Connector
This connector is connected to the MIPI power board.
1
2
3
4
95
6 8
7
10
11
12
13
14 20
19
18
17
16
15
[Figure 2-8. J13 Connector (Top View)]
[Table 7. J13 Connector Description]
No.
Name
Description
Remark
1
GND
Ground
2
GND
Ground
3
GPIO8
General Purpose IO8
Using PWR_DIO_xxx function
4
GPIO9
General Purpose IO9
Using PWR_DIO_xxx function
5
GPIO10
General Purpose IO10
Using PWR_DIO_xxx function
6
GPIO11
General Purpose IO11
Using PWR_DIO_xxx function
7
GND
Ground
8
GND
Ground
9
5V_IN
5V Power
5V
10
5V_IN
5V Power
5V
11
5V_IN
5V Power
5V
12
5V_IN
5V Power
5V
13
GND
Ground
14
GND
Ground
15
VCC12_WALL
12V Adaptor Power
12V
16
VCC12_WALL
12V Adaptor Power
12V
17
VCC12_WALL
12V Adaptor Power
12V
18
VCC12_WALL
12V Adaptor Power
12V
19
GND
Ground
20
GND
Ground

USB3-FRM22 User’s Manual
13
(9) J14 Connector
It is a connector used for Power/AD Convertor/OpenShort communication line and some
GPIOs.
1
2
3
4
95
6 8
7
10
11
12
13
14 20
19
18
17
16
15
[Figure 2-9. J14 Connector (Top View)]
[Table 8. J14 Connector Description]
No.
Name
Description
Remark
No.
Name
Description
Remark
2
GND
Ground
3
SCL
Serial Clock
3.3V
4
SDA
Serial Data
3.3V
5
PWR_SCL_FU
Power Serial Clock
3.3V
6
PWR_SDA_FU
Power Serial Data
3.3V
7
AD_SCL_FU
AD Converter Serial Clock
3.3V
8
AD_SDA_FU
AD Converter Serial Data
3.3V
9
OS_SCL_FU
Open/Short Serial Clock
3.3V
10
OS_SDA_FU
Open/Short Serial Data
3.3V
11
GND
Ground
12
GND
Ground
13
VCC12_WALL
12V Adaptor Power
12V
14
VCC12_WALL
12V Adaptor Power
12V
15
GPIO8
General Purpose IO8
1.5 ~ 3.3V
16
GPIO9
General Purpose IO9
1.5 ~ 3.3V
17
GPIO10
General Purpose IO10
1.5 ~ 3.3V
18
GPIO11
General Purpose IO11
1.5 ~ 3.3V
19
GND
Ground
20
GND
Ground

USB3-FRM22 User’s Manual
14
(10) J15 Connector
This connector is used for SPI (Serial Peripheral Interface) and some GPIOs.
1
2
3
4
95
6 8
7
10
11
12
13
14 20
19
18
17
16
15
[Figure 2-10. J15 Connector (Top View)]
[Table 9. J15 Connector Description]
No.
Name
Description
Remark
1
GND
Ground
2
GND
Ground
3
SPI_CLK_CON
Serial Clock
3.3V
4
SPI_MOSI_CON
Master Output, Slave Input
3.3V
5
SPI_EN_CON
Slave Select
3.3V
6
SPI_MISO_CON
Master Input, Slave Output
3.3V
7
GND
Ground
8
5V_IN
5V Power
5V
9
V_IO2
IO2 Power
V_IO2 Power
10
GND
Ground
11
GPIO0
General Purpose IO0
1.5 ~ 3.3V
12
GPIO1
General Purpose IO1
1.5 ~ 3.3V
13
GPIO2
General Purpose IO2
1.5 ~ 3.3V
14
GPIO3
General Purpose IO3
1.5 ~ 3.3V
15
GPIO4
General Purpose IO4
1.5 ~ 3.3V
16
GPIO5
General Purpose IO5
1.5 ~ 3.3V
17
GPIO6
General Purpose IO6
1.5 ~ 3.3V
18
GPIO7
General Purpose IO7
1.5 ~ 3.3V
19
GND
Ground
20
GND
Ground
(11) SW1 Switch
When the terminal is raised with the board power On/Off switch, the 12V power is turned
on.
12V
GND
12V DC Jack 1
2
3
[Figure 2-11. SW1 Switch]

USB3-FRM22 User’s Manual
15
(12) SW3 Switch
The USB3-FRM20 board is designed to use up to 4 USB3-FRM20 boards simultaneously in
one system (PC). Classification of each board can be set through a 2-pin DIP switch in the
board.
1
ON
SW3
2
[Figure 2-12. SW3 Switch (Top View)]
[표10. SW3 PIN-OUT Description]
1
2
Description
OFF
OFF
Board No. 0
ON
OFF
Board No. 1
OFF
ON
Board No. 2
ON
ON
Board No. 3

USB3-FRM22 User’s Manual
16
2-4. Board Size
The external dimensions of the board are as follows.
(For detailed dimensions, please ask the person in charge.)
< Top View >
10.7
1.6
3.0
15.5
< Right Side View >
110
80
11
3.0
8
53
100
70

USB3-FRM22 User’s Manual
17
3. Sample Program
A sample program is provided on the CDROM provided with the board so that the board can be
used easily. In order to test the sample program, the driver of the board must be installed first. The
sample program is provided in the form of a source so that the API provided to use the board can be
briefly tested, so the user can modify and use it.
[Figure 3-1. Sample Program Execution Screen]
To use the sample program above, an API (Application Programming Interface) is required. API is
provided in the form of "DLL", and import library and header file are required to compile.

USB3-FRM22 User’s Manual
18
All files specified above are included on the supplied CDROM. In order to run the sample
program normally, API DLL (USB-FRM22.DLL) must be in the folder of the executable file, or in the
Windows system folder or the folder designated by the Path environment variable.
The program execution sequence for viewing images is as follows.
①Device “Open” click
②Device “Init” click
③Pixel bit selection from “8, 16, 24, 32, 16bit YUV”
④Select from Address_Data Bit 8_8, 16_8, 16_16 among sensor initialization file contents
⑤Read the sensor initialization file saved as “S-Read” and click “Go”
⑥The video comes out automatically. Check resolution with Get Res.
⑦Click the “Start/Stop” toggle button to stop the video.
3.1 Description of Image Frame Functions
(1) “Device Open” button
Start the device on the selected board.
(2) “Board#” selection
In case of multiple USB3.0 boards, 4 board numbers (0 ~ 3) are assigned.
(3) “Ver” button
The board's FPGA and Firmware version are shown.
(4) “D-PHY” toggle
Check when using D-Phy.
(5) “Virtual Mode” toggle
Select when using MIPI Virtual Mode.
(6) “Device Init” button
Initialize the image frame function. When the power is first applied, it performed only
once. Select Video Data Mode from 8bit, 16bit, 24bit, 32bit, 16bit YUV.

USB3-FRM22 User’s Manual
19
(7) “S-Read” button
The sensor initialization file is read from the program. Depending on the address_data size
(8_8, 16_8, 16_16) of the above command, it is possible to send commands to the INI file at
a time or use the command line by line by I2C read/write. The structure and description of
the ini file are as follows. In the following example, the address_data size is 16_8, which is an
address 2-byte data 1-byte structure.
Ex) OV13850_4224x3136.ini file structure
[MISC] : Various types of (Miscellaneous) settings can be made.
5V_Power=1
IO_Power=1
SEN_Reset=1
SEN_Enable=1
COMBO_MODE=1 //D-Phy
DATA_BITS=3 //32bits
MCLK=24
[END]
[SENSOR_POWER] : Sensor power (0.9 ~ 4.1V) can be set.
SP0=4.0
SP1=4.0
SP2=4.0
SP3=4.0
SP4=0
SP5=0
[END]
[REGISTER] : Other sensor register settings
Slave 0x10 //change slave ID as Sensor
0x0103 01
0x0300 01
0x0301 00
0x0302 38
0x0303 00
0x030a 00
0x300f 11
0x3010 01
0x3011 76
…………….
0x5404 00