Data-Tronix DT-QAM-ENCMOD-8 User manual

Manual
DT-QAM-ENCMOD-8
User Manual

DT-QAM-ENCMOD-8 Manual
2
Table of Contents
Introduction ................................................................................................................... 3
Features ................................................................................................................... 3
 Specications ................................................................................................................ 3
Safety Instructions ........................................................................................................ 4
Unpacking and Handling............................................................................................... 5
Installation ................................................................................................................... 5
Front Panel ................................................................................................................... 6
Rear Panel ................................................................................................................... 6
Web Management .......................................................................................................... 7
Quick IP Ethernet Connection Guide......................................................................... 16
Common Troubleshooting .......................................................................................... 18
Warranty ................................................................................................................. 19

DT-QAM-ENCMOD-8 Manual
3
Introduction
The DT-QAM-ENCMOD-8 is designed with 8 HDMI input connectors. After encoding and
multiplexing, the device will modulate the signals into DVB-T/ T2, DVB-C, ATSC, ISDB and
DTMB standards. Thanks to its IP input port in the front panel, it can take
in the IP signal and output in RF signal as well.
Features
1. Video encoding in H.264 and audio encoding in MPEG and AAC.
2. Supports all major resolutions from 480i through 1080P
3. Supports CA PID ltering, remapping and PSI/SI editing
4. Easy conguration with built-in Web UI
Output
Standard DVB-C DVB-T ATSC J.83B DTMB
Bandwidth 6M 6, 7 or 8 M 6M 6 M 8 M
Constellation 64 QAM,
256 QAM
QPSK, 16QAM,
64QAM 8VSB 64 QAM, 256 QAM
QPSK, 16QAM,
32QAM, 64QAM
QAM_4NR
Other
Settings
Symbol Rate Code Rate
_ _
Code Rate
_
Guard Interval Interleave
2K, 4K, 8K Sync Frame
_ PN Phase
Input
Input Connector RJ45 - 1 GbE and HDMI - 8
Transport Protocol UDP, RTP
Max Input IP
Address 256
Input Transport
Stream MPTS and SPTS
General
Power
Consumption 60 W
Weight 8.2 lbs (3.71 kg)
Dimensions 12.52 x 10.24 x 1.73”
(318 x 260 x 44 mm)
Language English
Warranty 1-Year Limited Warranty
RF
Output Level ≥ 45dBmV
Frequency Range 50-999.999 MHzl
Out-band Rejection ≥60 dB
MER Typ. 38 dB
Specications

DT-QAM-ENCMOD-8 Manual
4
Safety Instructions
TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER FROM THIS UNIT. NO
USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN


1. Read all safety and operating instructions before you operate the modulator
2. Retain all safety and operating instructions for future reference
3. Heed all warnings on the modulator and in the safety and operating instructions
4. Follow all installation, operating and use instructions.
5. Unplug the modulator from the AC power outlet before cleaning. Use only a damp cloth for
cleaning the exterior of the modulator
6. Do not use accessories or attachments not recommended by us, as they may cause
hazards, and will void the warranty
7. Do not operate the modulator in high-humidity areas, or expose it to water or moisture.
8. Do not place the modulator on an unstable cart, bracket or table. The modulator may fall,
causing serious personal injury and damage to the modulator. Install the modulator only in a
mounting rack designed for 19” rack-mounted equipment.
9. Do not block or cover slots and openings in the modulator. These are provided for ventilation and
protection from overheating. Never place the modulator near or over a radiator or heat register.
10. We strongly recommend using an outlet that contains surge suppression or ground fault protec-
tion. For added protection during a lightning storm, or when the modulator is left unattended for
long periods of time, unplug it form the wall outlet or PDU and disconnect the lines between the
modulator and its source. This will prevent damage caused by lightning or power line surges.
11. Do not overload wall outlets or extension cords, as this can result in a risk of re or electrical
shock.
12. Never insert objects of any kind into the modulator through openings as the objects may touch
dangerous voltage and will void the warranty. Refer all servicing to authorized service personnel.
13. Unplug the modulator from the wall outlet or PDU and refer servicing to authorized service per-
sonnel whenever the following occurs:
• The power supply cord or plug is damaged
• Liquid has been spilled into or objects have fallen into modulator
• The modulator has been exposed to rain or water
• The modulator has been dropped or the chassis has been damaged
• The modulator exhibits a distinct change in performance
When replacement parts are required, ensure that the service technician uses replacement parts
specied by us.

DT-QAM-ENCMOD-8 Manual
55
Unpacking and Handling
A full DT-QAM-ENCMOD-8 is shipped with all equipment assembled, wired, factory tested, and then
packaged in an appropriate shipping container.
• DT-QAM-ENCMOD-8 digital modulator (QTY=1)
• Power Cord and 3-pin plug (QTY=1)
Mechanical Inspection
Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is clean,
and no wire, cable, or connectors are broken, damaged or loose.
Precautions
• Avoid heat buildup
• Ensure easy access to rack wiring
• Facilitate servicing and maintenance
• Avoid direct heating or air conditioning
• Make sure rack supports are su󰀩ciently rigid to support racks
• Beware of dripping water onto equipment form leaky roofs, waveguide roof entries and cold
water pipe condensations
Damage in Shipment
Should any damage be discovered after unpacking the unit, immediately contact
DataTronix at 800-688-9282.
The DT-QAM-ENCMOD-8 is designed to be installed in a rack shelf or a standard rack. Please fol-
low the instructions below to install the DT-QAM-ENCMOD-8 digital modulator:
1. Connect the power plug to the jack
2. Connect the video source to the DT-QAM-ENCMOD-8 modulator
3. Connect the DT-QAM-ENCMOD-8 to your laptop or computer
4. Power up the modulator
Installation

DT-QAM-ENCMOD-8 Manual
6
1. PWR Indicate power on.
2. RUN The light will keep ashing when system is on.
3. CH1-CH8
4. DEFAULT - Press for 10 seconds to restore the encoder to the factory setting
(Like the network setting and PID settings).
5. NMS - Net management system port
[IP:192.168.1.30; USER NAME: user ; PASSWORD: user]
Front Panel View
1. HD INPUT PORTS: Feed the HDMI signals into the modulator. The HD port
2. RF OUT: 40dBmV maximum output is provided at this port
3. TEST: Output level read at this point will be down 20dB from the actual output
4. POWER CORD: 12V 5A power source
5. ON/OFF SWITCH: Turns the unit on or o󰀨
6. GDN: For modulator grounding
WARNING:
For the protection of your equipment and its proper working, it is necessary to connect
the DT-QAM-ENCMOD-8 to a ground connection.
1
2
3 4
5
2 3
4
5
1
6
Rear Panel View

DT-QAM-ENCMOD-8 Manual
7
Web Management
Login:
The DT-QAM-ENCMOD-8 has a user friendly interface for programming and monitoring the
device. The user can access to the built-in web UI by logging into Google Chrome, Firefox or
Microsoft Edge accounts. (The best browsers)
The default user name and the default password are the following:
Username: user
Password: user
NOTE:
Please make sure your computers IP address is in the same subnet as the modulator.
Reminders:
1. Please change the user name and password if needed.
2. Username/password are case-sensitive and may contain letters or numbers.
3. Username/password must be a minimum of 1 byte and a maximum of 32 bytes in length.
System Page:
This page is a read-only one which displays the general health of the unit, such as temperature,
Input and output ports and Serial number. The information is provided as a quick way to monitor
the system or assist with troubleshooting issue.

DT-QAM-ENCMOD-8 Manual
8
Serial Number: The unique ID for this modulator.
Modulation: Indicates the RF output modulation.
Software Version: If there’s something wrong with this device, please send this information to us.
Temperature: Indicates the CPU working temperature in real-time.
Rear Panel: Indicates the input connector status. The green color means the HDMI cable is well
connected while the gray means disconnected.
Cooling Fans: There are four cooling fans installed in the left side of the case.
InputRo uter Output
InputRo uter Output
The fan is working. The fan is down. Please replace it.
Front Panel: The running status of the CPU
Setting Flow:
InputRo uter Output
Input Settings:
InputRo uter Output
In the input setting page, there might be di󰀨erent labels with di󰀨erent input cards. The rst one
here is the IP input signal and the second label is HDMI input signal.

DT-QAM-ENCMOD-8 Manual
9
IP Signal
Click the +Add button to add the IP address. >>>Choose the Multicast in normal situation and
input your IP address.
>>>Click Submit and the system will analysis the programs in IP address, which will be listed
out in the Router.
For quick input, we also provide step mode. There are three modes in it --IP address, Port and
IP address with port.
Choose any of them to meet your plan.
Step: The value range is from 1 to 10.
Count: The maximum value is 256. Notice that the note for this box is the available
input number.
Remove: To delete the IP address that you don’t want.
Submit: This Submit only be used when you modify the IP address manually.
9
9
9

DT-QAM-ENCMOD-8 Manual
10
HDMI Signal
Status Green light indicates normal working conditions. Greyed out indicates either the port
is unused, or input is not detected.
Channel 1-1 means the first HDMI port in the first card
Enable Enable and disable the HDMI input port
Input Resolution Display the input resolution
Output Resolution Downscale the input resolution
Service Name Input the service name here
Video Format For this device, it only supports H.264
Audio Format Select from MPEG and AAC
Set Bitrate Set the output bit rate here. And the maximum rate is 20,000Kbps.
Real Bitrate The real output bit rate
12
3
4
The router setting is the most important in this modulator. This is where you are able to view all
input channels, and forward to output frequencies

DT-QAM-ENCMOD-8 Manual
11
Frequency Bars
The usage indicator bar will move while the user sends programs to the output frequency. It is
not recommended to exceed 80% of the total bandwidth. If the input bitrate exceeds 80%, the
barcolor will turn Red from Green as a warning signal..
List Filter
The Router List contains too much information and streams. That’s why we provide the list lter
to show the information that users require.
Router List
In this list, you can see all the input streams and send the programs to the preset frequencies
by the Forward button.

DT-QAM-ENCMOD-8 Manual
12
STOP! DO NOT set the PMT PID, VIDEO PID and AUDIO PID with the same ID.
Stream Information
This information is a summary of the router list, which is very helpful to the operators.
Output
Channel List : In the OUTPUT page, we can reschedule the program and PIDs in a much easier
way.

DT-QAM-ENCMOD-8 Manual
13
RF Setting
In this page, you can set up the output modulation with its parameters and the output frequencies.
Reminder: The output frequencies are 4 continuous ones. You only need to ll the rst one and
the system will show the other three.
Mode Modulation Our device supports all the major modulation, but it will display one in a regular
device. Please contact our sales for more OEM requirements.
Modulation Settings Dierent combination will have dierent bandwidth. We suggest you leave it as
defaulted.
RF Enable RF channel enable
Frequency Input the frequency in the first box and the system will do the rest.

DT-QAM-ENCMOD-8 Manual
14
System
Network Setting
Making changes in this area can a󰀨ect the system communication. PROCEED WITH CAUTION.
Management in IP address should only be changed when it is necessary to manage the entire
system from a di󰀨erent subnet. Otherwise, please leave what it is.
IGMP Version : If your input IP stream contains IGMP, please select the right version to match the
input ones.
Account

DT-QAM-ENCMOD-8 Manual
15
System Parameter
Upgradesystemfromle: Upgrade the modulator with the latest software.
Restore to factory settings: The restore function will recover the input and output settings and
the IP address to the factory mode.
Reboot: To reboot the modulator.
Export Settings: Back up the input and output settings to your computer.
Import Settings: Recover the settings to the modulator from your computer.
NOTICE: Additional reset option.
Press the default button on the front panel for 3 to 5 seconds. Restore is complete when the run
light begins ashing.

DT-QAM-ENCMOD-8 Manual
16
Quick IP Ethernet Connection Guide
NOTICE: Make sure you login your operation system as the administrator.
1. Go to “Window Start”
2. Go to Window Settings
3. Go to “ Network & Internet”
4. Go to “Ethernet” on the left side of the menu
5. Go to “ Change adapter options”
6. Double click on the Ethernet Source or Right Click and select “Properties”

DT-QAM-ENCMOD-8 Manual
17
7. Open Properties
8. Go to “Internet Protocol Version 4 (TCP/IPv4)
9. Go to “Properties”
10. Go to “Use the following IP address”

DT-QAM-ENCMOD-8 Manual
18
11. Set IP address
Set IP address: 192.168.1.10
Set Subnet mask: 255.255.255.0
Set Default gateway: 192.168.1.1
12. Save all the settings.
Symptom Recommended Action
1 Power LED is not lit. 1-1 means the rst HDMI port in the rst card
2 Can’t login to the NMS Enable and disable the HDMI input port
3The WEB UI is not in order
and can’t save the settings Display the input resolution
4 CH1 to CH8 LED are not lit Downscale the input resolution
5 Unknown shown in the NMS Input the service name here
6 Other issue For this device, it only supports H.264
Common Troubleshooting

DT-QAM-ENCMOD-8 Manual
19
DATATRONIX 1-Year Limited Warranty
DATATRONIX. (the “Company”) warrants to the Original Purchaser that the item purchased is
free from defects in workmanship or material under normal use. This warranty starts on the date
of shipment of the hardware to the Original Purchaser.
During the warranty period, the Company agrees to repair or replace, at its sole option, without
charge to Original Purchaser, any defective component. To obtain service, the Original Purchaser
must return the item to the Company properly packaged for shipping. All defective products must
be returned to the Company within thirty (30) days of failure. Products must be returned with
a description of the failure and Return Merchandise Authorization (RMA) number supplied by
the Company. To receive a RMA number and a return shipping address on where to deliver the
hardware, call 610-429-1821. The shipping, and insurance charges incurred in shipping to the
Company will be paid by Original Purchaser, and all risk for the hardware shall remain with the
Original Purchaser until such time as Company takes receipt of the hardware. Upon receipt, the
Company will promptly repair or replace the defective unit, and then return said unit to Original
Purchaser, shipping prepaid. The Company may use reconditioned or like-new parts or units, at
its sole option, when repairing any hardware. Repaired products shall carry the same amount of
outstanding warranty as from original purchase. Any claim under the warranty must include dated
proof of purchase or invoice. In any event, the Company’s liability for defective hardware is limited
to repairing or replacing the hardware.
This warranty is contingent upon proper use of the hardware by Original Purchaser and does
not cover: if damage is due to Acts of God (including re, ood, earthquake, storm, hurricane or
other natural disaster), accident, unusual physical, electrical, or electromechanical stress, mod-
ications, neglect, misuse, operation with media not approved by the Company, tampering with
or altering of the hardware, riot, war, invasion, act of foreign enemies, hostilities (regardless of
whether war is declared), civil war, rebellion, revolution, insurrection, military or usurped power or
conscation, terrorist activities, nationalization, government sanction, blockage, embargo, labor
dispute, strike, lockout or interruption or failure of electricity, air conditioning, or humidity control,
Internet, network, or telephone service.
The warranties given herein, together with any implied warranties covering the hardware, includ-
ing any warranties of merchantability or tness for a particular purpose, are limited in duration to
one year from the date of shipment to the Original Purchaser. Jurisdictions vary with regard to the
enforceability of warranty limitations, and you should check the laws of your local jurisdiction to
nd out whether the above limitation applies to you.
The Company shall not be liable to your for loss of data, loss of prots, lost savings, special, inci-
dental, consequential, indirect, or other similar damages arising from breach of warranty, breach
of contract, negligence, or other legal action even if the Company or its agent has been advised of
Warranty

DT-QAM-ENCMOD-8 Manual
20
the possibility of such damages, or for any claim brought against your by another party. Jurisdic-
tions vary with regard to the enforceability of provisions excluding or limiting liability for incidental
or consequential damages. You should check the laws of your local jurisdiction to nd out whether
the above exclusion applies to you.
This warranty allocates risks of product failure between Original Purchaser and the Company.
The Company’s hardware pricing reects this allocation of risk and the limitations of liability con-
tained in this warranty. The warranty set forth above is in lieu of all other express warranties,
whether oral or written. The agents, employees, distributors, and dealers of the Company are not
authorized to make modication to this warranty, or additional warranties binding on the Compa-
ny. Accordingly, additional statements such as dealer advertising or presentations, whether oral
or written, do not constitute warranties by the Company and should not be relied upon.
This warranty gives you specic legal rights. You may also have other rights which vary from one
jurisdiction to another.