Data Video RMC-90 User manual

RMC-90 REMOTE CONTROL
PANEL FOR SE-800
User’s Guide
http:// www.datavideo-tek.com

Service, Support and Warranty
It is our goal to make your product ownership a satisfying experience. Our support
staff is available to assist you in setting up and operating your system. If needed,
our convenient repair service is at your disposal. Please refer to the product support
information below, or write us at
 Datavideo Corporation (USA)
12300-U East Washington Blvd., Whittier, CA 90606 USA
Tel: [phone] E-mail: [e-mail]
 Datavideo Technologies Europe BV
Californiedreef 26 3565 BL Utrecht, The Netherlands
Tel: [phone] E-mail: [email protected]
 Datavideo Technologies Co., Ltd.
7F. No. 352, Sec. 2, Chung Shan Rd. Chung Ho City, Tai-Pei Hsien, Taiwan
Tel: [phone] E-mail: [email protected]
Product Support
For information or assistance with the setup, operation, troubleshooting, or repair of
your system, you may first wish to call the dealer from whom you purchased.
If necessary, please feel free to call the Datavideo Help Desk above:
From Monday through Friday, 9:00 am through 6:00 PM Local time
You may also contact our International web site at (http://www.datavideo-tek.com)
or our international service at (s[email protected]) any time.
2

CONTENTS
INTRODUCTION
4
WHAT’S IN THE PACKAGE
4
CONTROL PANEL
5
REAR PANEL CONNECTION
9
MORE PERIPHERALS
11
3

Introduction
RMC-90 is a Remote Control Panel specially designed to work with SE-800 control
panel simultaneously. RMC-90 provides a wired remote function of video channel
selection keys, programmable effect function keys, T-Bar control…most of the
control key functions from SE-800. It includes a Tally control for the Datavideo
TLM-404 LCD panels and three GPI triggers to control Datavideo DV Bank.
What’s in the Package
1. RMC-90 unit
2. 15-pin D-sub TLM-404 LCD TALLY control cable
3. 9-Pin D-sub RS-232 interface cable for connecting SE-800
4. GPI trigger cables for DV Bank control
5. XLR male to XLR female power cable for connecting SE-800
6. DC cable, Plug with lock, 12V output.
7. User’s Guide
4

Control Panel
Audio Select for channel A, B, C or D and A+V function key
This row of selector buttons has a internal LED to show which input channel is
active. If the A+V function key is engaged (LED on), the audio source channel
selected on the Main Source bus is automatically selected. If A+V is not
engaged, the input source is user selectable.
Please refer to the “Front Panel” section of SE-800 instruction manual for a
more detailed description.
5

Video Main-source and SUB-source Select for channel A, B, C or D and BK
(Background) function key
It is used to select which of the four video input channels or background will be
selected as Main Source and which of the four video input channels or
background will be transitioned to or used as a sub source in an effect.
For more information, please refer to the “Front Panel” section of SE-800
instruction manual.
6

F1-F10 and F11-20, F21-30
Control of the 30 users programmable preset locations for storing customized
effects and transitions.
The numbered buttons 1-10 above access 10 locations. To access F11 to F20,
you need to first press the F11-20 button until the LED is lit, then press one of
the single numbered buttons to access presets F11-F20. To access F21-F30,
please follow the same procedure.
To store or playback a transition or effect from preset function keys, please
refer to the “Front Panel” section of SE-800 instruction manual for detail.
GPI-1 to GPI-3
Enable the three terminals GPI
trigger output on rear panel for
video play-pause control of
Datavideo DV Bank
7

T-bar is for performing effect transitions manually.
It can be either all the way up, all the way down, or
anywhere in between. To enable the SE-800 T-Bar,
the T-Bar on RMC-90 must be at either end of its
travel.
PLEASE NOTE, T-Bar on RMC-90 CAN NOT
CONTROL AN AUDIO ONLY FADE EFFECT, it
controls only Video or Video with embedded audio
effect.
Each press on this button will
playback the pre-stored function
key’s effect sequentially
Press on the button to
Auto-Play the effect
Turn on LED to enable
the T-Bar effect control
for video
Press to turn on LED to
enable the GPI Trigger
input control on SE-800
Turn on LED to enable the T-Bar
Audio effect control.
Note: Push down the T-Bar to
mute Audio
8

Rear Panel connection
GPI Trigger outputs
to control DV Bank
Connect to Datavideo TLM-404
4”x4 TFT LCD or connect the
external video devices Tally
control interface, such as
Camcra
Connect to SE-800
Remote RS-232 interface
9

DC 14.4 --- 15V input from
SE-800 Power adaptor
DC 12V 0.5A output to
connect BAC-03 Audio
converter
DC 14.4 --- 15V output to
SE-800 Power input
10

More Peripherals
Datavideo TLM-404 4”x4 TFT LCD panel
Datavideo DV Bank Native DV recorder and GPI Trigger cable
Built-in 120GB HDD for 9 hours native DV recording
Datavideo BAC-03 Balanced-Unbalanced Audio converter
11

All the trademarks are the properties of their respective owners.
Datavideo Technologies Co., Ltd. All rights reserved 2003.
P/N: 082061305E1
12