Datalogic Controller SC6000 User manual

SC6000 Controller
QUICK REFERENCE GUIDE

CONTENTS
SC6000-1200 STANDARD MODEL ........................................................................................................................1
SC6000-1211 PROFIBUS MODEL ..........................................................................................................................4
SC6000-1215 DEVICENET MODEL ........................................................................................................................5
SC6000-1230 DUAL ETHERNET MODEL ..............................................................................................................6
COMMON FEATURES ............................................................................................................................................7
NOTE
For further details on product installation, see the complete Reference Manual available on the
configuration CD-ROM included with this product.

SC6000 STANDARD MODEL
1
SC6000-1200 STANDARD MODEL
Figure A
Connector Panel
1
Figure B
Power ON and Communication LEDs
1
Status LEDs
3
LCD Display
2
Programming Keypad
4
Connector Panel Legend
5
3
4
2
1
5
1
234
65
1
Figure C
Modem Connector
1
Power/Net Connector
2
Main Interface Connector
3
Ethernet Connector
4
A
uxiliary Interface Connector
5
Extended I/O Connector
6

SC6000 STANDARD MODEL
Electrical Connections
The SC6000 is designed to easily connect to the PWO power supply through two standard accessory cables. All
system cabling is concentrated at the PWO except for some Host connections and the Auxiliary interface for
SC6000 configuration using a laptop PC.
The following connector pinouts are given for reference.
MAIN INTERFACE
Pin RS232 RS485 Full Duplex
2 TX TX485 +
3 RX RX485 +
5 GND_ISO GND_ISO
7 CTS RX485 -
8 RTS TX485 -
51
96
9-pin D-sub Female Connector
CAUTION
Do not connect GND and GND_ISO to different (external) ground references. GND and
GND_ISO are internally connected through filtering circuitry which can be permanently
damaged if subjected to voltage drops over 0.8 Vdc.
AUXILIARY INTERFACE
Pin Name Function
2 TX Transmit
3 RX Receive
5 GND Ground
51
96
9-pin D-sub Female Connector
MODEM CONNECTOR
Pin Name Function
1 CD Carrier detect
2 RX Receive
3 TX Transmit
4 DTR Data terminal ready
5 GND Ground
6 DSR Data set ready
7 RTS Request to send
8 CTS Clear to send
9 RI Ring indicator
15
69
9-pin D-sub Male Connector
ETHERNET CONNECTOR
Pin Name Function
1 TX + Transmitted data (+)
2 TX - Transmitted data (-)
3 RX + Received data (+)
6 RX - Received data (-)
4, 5, 7, 8 N.C. Not connected
1 8
RJ45 Modular Connector
2

SC6000 STANDARD MODEL
Typical Layouts
Ethernet Connection
Main Connection
Modem Connection
3

SC6000 PROFIBUS MODEL
4
SC6000-1211 PROFIBUS MODEL
234
76
1
5
SC6000 Profibus Connector Panel
Modem Connector
1
Power/Net Connector
2
Main Interface Connector
3
Profibus Connector
5
A
uxiliary Interface Connector
6
Extended I/O Connector
7
Ethernet Connector
4
PROFIBUS CONNECTOR
Pin Name Function
1 Shield* Shield, protective ground resp.
2 N.C. Not connected
3 B-LINE (RxD/TxD-P) Received/Transmitted data-P
4 CNTR-P** Repeater control signal
5 DGND Data ground (M5V)
6 +5 V Voltage plus (P5V)
7 N.C. Not connected
8 A-LINE (RxD/TxD-N) Received/Transmitted data
9 CNTR-N** Repeater control signal
51
96
9-pin D-sub Female Connector
* signal is optional
** signal is optional; RS485 level
Fieldbus Network

SC6000 DEVICENET MODEL
5
SC6000-1215 DEVICENET MODEL
234
76
1
5
SC6000 DeviceNet Connector Panel
Modem Connector
1
Power/Net Connector
2
Main Interface Connector
3
DeviceNet Connector
5
A
uxiliary Interface Connector
6
Extended I/O Connector
7
Ethernet Connector
4
DEVICENET CONNECTOR
Pin Name Function
2 V+ Supply voltage – positive pin
5 CAN_L CAN bus data line – L
1 SHIELD Shield
4 CAN_H CAN bus data line – H
3 V- Supply voltage – negative pin
1
3
2
4
5
5-pin male DeviceNet Connector
Fieldbus Network

SC6000 DUAL ETHERNET MODEL
6
SC6000-1230 DUAL ETHERNET MODEL
SC6000 Dual Ethernet Connector Panel
234
76
1
5
Modem Connector
1
Power/Net Connector
2
Main Interface Connector
3
Second Ethernet Connector
5
A
uxiliary Interface Connector
6
Extended I/O Connector
7
Ethernet Connector
4
ETHERNET CONNECTOR
Pin Name Function
1 TX + Transmitted data (+)
2 TX - Transmitted data (-)
3 RX + Received data (+)
6 RX - Received data (-)
4, 5, 7, 8 N.C. Not connected
1 8
RJ45 Modular Connector
Dual Ethernet Connection

COMMON FEATURES
COMMON FEATURES
Overall Dimensions
319.5
[12.58]
248.7
[9.79]
80.2
[3.16]
99.7
[3.93]
124.4
[4.90]
39.7
[1.56]
MØ8
39.7
[1.56]
124.4
[4.90]
298
[11.73]
mm
inch
SC6000 Overall Dimensions
180
[7.09]
309
[12.17]
5
[0.20]
N°2R15
[R0.59]
15
[0.59]
50
[1.97]
48
[1.89]
N°6 8
[0.32]
80
[3.15]
95
[3.74]
40
[1.57]
85
[3.35]
50
[1.97]
85
[3.35]
48
[1.89]
300
[11.80]
40
[1.57]
40
[1.57]
8
[0.33]
N°2R10
[R0.39]
N°2Ø56
[Ø2.22]
M8
16
[0.63]
16
[0.63]
30
[1.18]
15
[0.59]
N°2Ø8
[Ø0.33]
20
[0.79]
mm
inch
ST-222 Bracket Overall Dimensions
7

COMMON FEATURES
8
Mechanical Installation
To mount the SC6000 Controller on the reading station frame proceed as follows:
1 Mount the bracket on the reading station frame: the slots on the bracket will help obtain the best positioning.
When working in environments characterized by strong vibrations, set the screws as close as possible to the
bracket edges, see the figure below.
2 Tighten the ST-222 bracket to the reading station frame using the screws and washers.
Mounting the bracket on the conveyor
3 Position the SC6000 Controller at the top of the bracket: make sure the two large round openings coincide to
the ones located at the edges of the SC6000 Controller.
4 While supporting the SC6000 Controller, rotate the whole device until it is aligned for the best viewing
position, then insert the set pin screw with locking washer until it inserts into one of the small positioning
holes located on the terminal bracket.
SC6000 Controller Side View with Punched Steel Ring and Relative Set Pin Screw
Set pin screw
The specially punched steel ring has been designed to obtain the most precise rotation possible in terms of
angle calibration, steadiness and consequent absence of torque between both sides of device.