Datasensor S62 B Series User manual

S62…B
Polarised retroreflex
INSTRUCTION MANUAL
CONTROLS
OUTPUT LED (yellow)
The yellow LED ON indicates the following output
status: N.O. closed and N.C. open.
STABILITY LED (green)
The green LED permantely ON indicates a stable
operating condition, where the signal received has a
safety margin higher than 30% respect to the output
switching value. The sensor is ready to function
correctly.
SENSITIVITY TRIMMER (ADJ.)
A mono-turn trimmer adjusts the sensitivity and the
sensor operating distance.
See the “SETTING” paragraph for the functioning
mode.
NOTE: the maximum trimmer mechanical rotating
range is equal to 240°. Do not force over the maximum
e minimum positions.
INSTALLATION
The sensor can be
positioned by means of
the three housing’s
holes using two screws
(M4x25 or longer, 1.5
Nm maximum tightening
torque) with washers.
Various orientable fixing
brackets to ease the sensor positioning are available
(please refer to the accessories listed in the
catalogue).
The operating distance is measured from the front
surface of the sensor optics.
The M12 connector can be oriented at two different
positions using the specific fastening spring and
rotating the block of 180°.
TECHNICAL DATA
Power supply: 10 … 30 Vdc (limit values)
Ripple: 2 Vpp max.
Current consumption
(output current excluded): < 30 mA
Outputs: PNP or NPN N.O. / N.C.; 30 Vdc max. (short-circuit protection)
Output current: 100 mA max (overload and overvoltage protection)
Output saturation voltage: ≤2 V
Response time: 500 µs max.
Switching frequency: 1 kHz
Indicators: OUTPUT LED (YELLOW) / STABILITY LED (GREEN)
Setting: mono-turn sensitivity adjustment trimmer
Operating temperature: -10 … 55 °C
Storage temperature: -20 … 70 °C
Dielectric strength: 500 Vac / 1 min. between electronic parts and housing
Insulation resistance: >20 MΩ/ 500 Vdc, between electronic parts and housing
Operating distance (typical values): 0.1…8 m su R2 (EG = 2)
Emission type: RED (640 nm)
Ambient light rejection: according to EN 60947-5-2
Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for each axis (EN60068-2-6)
Shock resistance: 11 ms (30 G) 6 shocks for each axis (EN60068-2-27)
Housing material: ABS
Lens material: window in PMMA, lenses in polycarbonate
Mechanical protection: IP67
Connections: 2 m ∅4 mm cable / M12 4-pole connector
Weight: 90 g. max. (cable version) / 40 g. max. (connector version)
CONNECTIONS
SETTING
Alignement:
- Align sensor and reflector on opposite sides at the necessary
distance.
- Rotate in the clockwise direction the sensitivity adjustment
trimmer (ADJ.) to maximum level.
- Moving the sensor vertically and horizontally, establish the
powering and turning off of the yellow LED (OUT) and fix the
sensor at in the middle. The best alignment is obtained in the
following condition: yellow LED permanently OFF and green
LED permanently ON.
Control:
- Place the target between the
sensor and the reflector. Control
that the yellow LED turns ON.
- Remove the target and control
that the yellow LED turns OFF again.
DIMENSIONS
42
50
0.75
2
42
50 1.1
18x45°
14
11 6
18
4.7
16
M12
Ø15
6.18
10.7
OUTPUT LED
STABILITY LED
CABLE VERSION
Ø4
SENSITIVITY TRIMMER
mm
25
EX-II-3D T6
Temperature class:
T6 (<85°C)
Max. Power consumpti 540 mW at 30 Vdc
Max. Internal capacita
n
100 nF
Internal inductance: negligible
DECLARATION OF CONFORMITY
We DATASENSOR S.p.A. declare under our sole responsibility that
these products are conform to the 2004/108 CEE, 73/23 CEE Directives
and successive amendments.
WARRANTY
DATASENSOR S.p.A. warrants its products to be free from defects.
DATASENSOR S.p.A. will repair or replace, free of charge, any product
found to be defective during the warranty period of 36 months from the
manufacturing date.
This warranty does not cover damage or liability deriving from the
improper application of DATASENSOR products.
DATASENSOR S.p.A. Via Lavino 265
40050 Monte S. Pietro - Bologna - Italy
Tel: [phone] Fax: [phone]
http://www.datasensor.com e-mail: [e-mail]
DATASENSOR S.p.A. cares for the environment: 100% recycled
paper.
DATASENSOR S.p.A. reserves the right to make modifications
and improvements without prior notification.
826003020 Rev.00

S62…M
Background suppression
INSTRUCTION MANUAL
CONTROLS
OUTPUT LED (yellow)
The yellow LED ON indicates that the N.O. output is closed and the N.C.
output is open.
STABILITY LED (green)
When permanently ON, the green LED indicates a normal operating condition
where the received signal has a safety margin superior to 30% respect to the
output switching value. The sensor is ready to function correctly (stability
condition).
DISTANCE ADJUSTMENT TRIMMER (ADJ.)
A 6-turn trimmer allows the background suppression distance adjustment
through a mechanical variation of the optic triangulation angle.
The operating distance increases, rotating the screws in a clockwise direction.
Please refer to the “SETTING” paragraph for acquisition or setup procedure
indications.
POSITION INDICATOR
This indicator presents a scale numbered from 1 to 6 that allows a precise
adjustment of the suppression distance in the entire operating range.
Please refer to the “SETTING” paragraph for use indications.
TIMER ADJUSTMENT TRIMMER (only. M05/M15/M25/M35 vers.)
This control allows to vary the output delay deactivation from 0 to 1 sec.
Please refer to “TIMER FUNCTIONS” paragraph for use indications.
INSTALLATION
The sensor can be positioned by means
of the three housing’s holes using two
screws (M4x25 or longer, 1.5Nm max.
tightening torque) with washers.
Various orientable fixing brackets to
ease the sensor positioning are
available (please refer to the general
catalogue).
The operating distance is measured
from the front surface of the sensor optics.
The M12 connector can be oriented at two different positions using the
specific fastening spring and rotating the block of 180°.
CONNECTIONS
M12 connector
TECHNICAL DATA
S62-M0… S62-M1… S62-M2… S62-M3…
Power supply: 10 … 30 VDC
Ripple: 2 Vpp max.
Consumption
(output current excluded): 40 mA max.
Outputs: PNP or NPN N.O./N.C.; 30 Vdc max. (short-circuit protection)
Output current: 100 mA (overload and overvoltage protection)
Output saturation voltage: ≤2 V
Response time: 500 µs 1 ms 1,5 ms
Switching frequency: 1 kHz 500 Hz 330 Hz
Emission type: RED (660 nm) INFRARED (880 nm)
Spot dimension: 6x6 mm (at 200 mm) 15x15 mm (at 400 mm) 200x200 mm (at 2000 mm)
Operating distance (typical values): 30…300 mm 60…600 mm 60…1200 mm 200…2000 mm
(recommended target 400x400mm)
Adjustment: Multiturn distance adjustment trimmer / Timer adjustment trimmer (only M05/M15/M25/M35 vers.)
Difference (90% white / 4% black): < 8 % < 12 % < 25 % < 30 %
Hysteresis (90% white): < 5 % < 20 %
Indicators: OUTPUT LED (YELLOW) / STABILITY LED (GREEN)
Operating temperature: -10 … 55 °C
Storage temperature: -20 … 70 °C
Insulating strength: 500 Vac 1 min., between electronics and housing
Insulating resistance: >20 MΩ500 Vdc, between electronics and housing
Ambient light rejection: According to EN 60947-5-2
Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for each axis (EN60068-2-6)
Shock resistance: 11 ms (30 G) 6 shock for each axis (EN60068-2-27)
Housing material: ABS
Lens material: PMMA window; PC lens
Mechanical protection: IP67
Connections: 2 m cable ∅4 mm / M12-4 pole connector
Weight: 90 g. max. cable vers. / 40 g. max. connector vers.
SETTING
Suppression distance setting
1.Object detection
Position object to detect in front of the sensor at the distance required.
Turn distance adjustment trimmer (ADJ) to minimum: yellow LED OFF and
green LED ON.
Rotate trimmer in a clockwise direction until the yellow LED and green LED
turn ON. Object detection condition (A status of position indicator)
A
2.Background suppression
Remove object and ensure that the background is in front of the sensor:
yellow LED OFF and green LED ON.
Rotate trimmer in a clockwise direction until the yellow LED and green LED
turn ON: background detection condition (B status of position indicator).
B
The trimmer reaches maximum level with yellow LED OFF if the background
is outside the operating range.
Rotate trimmer in an anticlockwise direction until yellow LED turns OFF
and green LED ON: condition where background is outside operating
range (C status of position indicator).
C
3.Setting and control
Rotate trimmer in an anticlockwise direction until the indicator reaches
an intermediate point between position A and C.
If position A and C are close to each other, leave trimmer on position C.
The sensor is now ready to function correctly and in stable conditions:
DIAGRAMMA DI RILEVAZIONE
DIMENSIONS
Ø4
18.4
1114
POSITION INDICATOR
DISTANCE ADJUSTMENT TRIMMER
OUTPUT LED
STABILITY LED
10.7
mm
42
50
6
11
6.18
TIMER ADJUSTMENT
TRIMMER (mod.M05/M15/M25/M35)
M12
Ø15
14
CABLE VERSION
18x45°
16
42
50
0.75
1.1
2
18
4.7
EMITTER
RECEIVER
18.215.5
TIMER FUNCTION (S62…M05/M15/M25)
The timer function allows to adjust the output deactivation delay when the
object is outside the detection area. The delay extends the output activation
allowing the slower interface systems to detect shorter pulses.
The delay adjustment is carried-out manually using the Timer adjustment
trimmer. Clockwise rotation increase the delay from 0 to a max. 1 sec. value.
EX-II-3-D T6
Temperature class:
T6 (<85°C)
Max. Power consumption: 1260 mW at 30 Vdc
Max. Internal capacitance: 130 nF
Internal inductance: negligible
DECLARATION OF CONFORMITY
We DATASENSOR S.p.A. declare under our sole responsibility that these products are conform to the
2004/108/CE, 2006/95/CE Directives and successive amendments.
WARRANTY
DATASENSOR S.p.A. warrants its products to be free from defects.
DATASENSOR S.p.A. will repair or replace, free of charge, any product found to be defective during the
warranty period of 36 months from the manufacturing date.
This warranty does not cover damage or liability deriving from the improper application of
DATASENSOR products.
DATASENSOR S.p.A. Via Lavino 265
40050 Monte S. Pietro - Bologna - Italy
Tel: [phone] Fax: [phone]
http://www.datasensor.com e-mail: [e-mail]
DATASENSOR S.p.A. cares for the environment: 100% recycled paper.
DATASENSOR S.p.A. reserves the right to make modifications and improvements without
prior notification.
826002872 Rev.C

S62-PL…B Laser
Polarised retroreflex
INSTRUCTION MANUAL
CONTROLS
OUTPUT LED (yellow)
The yellow LED ON indicates the following output status: N.O.
closed and N.C. open.
POWER ON LED (green)
The green LED ON indicates the sensor powering status and
laser emission presence.
SENSITIVITY TRIMMER (ADJ.)
Monoturn trimmer that adjusts the sensitivity and thus the
sensor operating distance.
Please refer to “SETTING” paragraph for the correct use
procedure.
WARNING: the maximum mechanical trimmer rotation is
equal to 240°. Do not apply excessive torque over the
maximum and minimum positions.
INSTALLATION
The sensor can be positioned by
means of the three housing’s
holes using two screws (M4x25
or longer, 1.5 Nm maximum
tightening torque) with washers.
Various orientable fixing brackets
to ease the sensor positioning
are available (please refer to the accessories listed in the
general catalogue).The operating distance is measured from
the front surface of the sensor optics.
The M12 connector can be oriented at two different positions
using the specific fastening spring and rotating the block to
180°.
CONNESSIONS
M12 connector
TECHNICAL DATA
Power supply: 10 … 30 Vcc
Ripple: 2 Vpp max.
Consumption
(output current excluded): 30 mA max
Outputs: PNP or NPN N.O. / N.C.; 30 Vdc max. (short-circuit protection)
Output current: 100 mA max (overload and overvoltage protection)
Output saturation voltage: ≤2 V
Response time: 200 µs
Switching frequency: 2.5 kHz
Emission type: RED LASER (λ= 645…665 nm): Class 2 EN 60825-1 (1994), Class II CDRH 21
CFR PART 1040.10
Pulsed emission: pot. max ≤5 mW; pulse duration = 5 µs;
frequency max = 32 KHz
Operating distance (typical values): refer to TAB.1
Min. detectable object dimension: 0.5 mm at 0.5m (minimum spot)
Indicators: OUTPUT LED (YELLOW) / POWER ON LED (GREEN)
Setting: Monoturn sensitivity adjustment trimmer
Functioning temperature: -10 … 55 °C
Storage temperature: -20 … 70 °C
Dielectric strength: 500 Vac 1 min., between electronics and housing
Insulating resistance: >20 MΩ500 Vdc, between electronics and housing
Ambient light rejection: according to EN 60947-5-2
Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6)
Shock resistance: 11 ms (30 G) 6 shock for every axis (EN60068-2-27)
Housing material: ABS
Lens material: PMMA window, polycarbonate lenses
Mechanical protection: IP67
Connections: M12 4-pole connector
Weight: 40 g. max.
SETTING
Alignment:
- Position the sensor and reflector aligned on opposite sides at the
desired distance.
- Turn to maximum the sensitivity adjustment trimmer (ADJ.)
(clockwise).
- Determine the powering on and powering off points of the yellow LED
(OUT) by moving vertically and horizontally the sensor and mount the
sensor in the middle of the points found.
Control:
- Enter laterally the object inside the
operating field and control that the
yellow LED turns on.
- Remove the object and check that
the yellow LED turns off immediately
PERFORMANCES
TAB.1: Operating distances (m)
REFLECTOR
R1 R2 R6 R7 /R20 R8
0.3 … 16 0.3 … 20 0.4 … 22 0.3 … 22 0.2 … 2
Note: The use of the RT 3970 reflecting tape is not suggested.
DIMENSIONS
18x45°
50
42
11
SENSITIVITY TRIMMER
10.7 POWER ON LED
OUTPUT LED
25
6.18 mm
614
Ø15
16
M12
42
1.1
50
20.75
18
4.7
21.5 8.5
RECEIVER
EMITTER
SAFETY PRECAUTIONS
All the electric and mechanical
safety regulations have to be
respected during sensor
functioning.
The sensor has to be protected
against mechanical damage.
Apply the labels supplied in a
visible position near the laser emission beam.
Do not stare directly into the laser beam!
Do not point the laser beam towards people!
Eye irradiation superior to 0.25 seconds is dangerous.
Please refer to the Class 2 Standard (EN60825-1).
These sensors can not be used for safety applications!
EX-II-3D T6
Temperature class:
T6 (<85°C)
Max. Power consumption: 800 mW at 30 Vdc
Max. Internal capacitance: 100 nF
Internal inductance: negligible
DECLARATION OF CONFORMITY
We DATASENSOR S.p.A. declare under our sole responsibility that
these products are conform to the 2004/108/CE, 2006/95/CE Directives
and successive amendments.
WARRANTY
DATASENSOR S.p.A. warrants its products to be free from defects.
DATASENSOR S.p.A. will repair or replace, free of charge, any product
found to be defective during the warranty period of 36 months from the
manufacturing date.
This warranty does not cover damage or liability deriving from the
improper application of DATASENSOR products.
DATASENSOR S.p.A. Via Lavino 265
40050 Monte S. Pietro - Bologna - Italy
Tel: [phone] Fax: [phone]
http://www.datasensor.com e-mail: [e-mail]
DATASENSOR S.p.A. cares for the environment: 100% recycled
paper.
DATASENSOR S.p.A. reserves the right to make modifications
and improvements without prior notification.
826003251 Rev.B
spot diameter (mm)
distance (mm)

S62-PL…M Laser
Background suppression
INSTRUCTION MANUAL
CONTROLS
OUTPUT LED (yellow)
The yellow LED ON indicates the output status: N.O. closed and N.C. open.
POWER ON LED (green)
The green LED ON indicates the sensor powering status and laser emission
presence.
DISTANCE ADJUSTMENT TRIMMER (ADJ.)
The multiturn trimmer with clutch (6 turn) adjusts the suppression distance
through the mechanical variation of the optic triangulation angle.
The operating distance increases rotation the trimmer shaft in a clockwise
direction.
Please refer to “SETTING” paragraph for the correct use procedure.
POSITION INDICATOR
This indicator has a scale numbered from 1 to 6 that allows the precise
adjustment of the suppression distance on the entire operating range.
Please refer to “SETTING” paragraph for the correct use procedure.
INSTALLATION
The sensor can be positioned by means
of the three housing’s holes using two
screws (M4x25 or longer, 1.5 Nm
maximum tightening torque) with
washers.
Various orientable fixing brackets to
ease the sensor positioning are
available (please refer to the
accessories listed in the general
catalogue).
The operating distance is measured from the front surface of the sensor
optics.
The M12 connector can be oriented at two different positions using the
specific fastening spring and rotating the block to 180°.
CONNECTIONS
M12 connector
TECHNICAL DATA
S62-PL-M01… S62-PL-M11…
Power supply: 10 … 30 VDC
Ripple: 2 Vpp max.
Consumption
(output current excluded): 30 mA max
Outputs: PNP or NPN N.O. / N.C.; 30 VDC max. (short-circuit protection)
Output current: 100 mA (overload and overvoltage protection)
Output saturation voltage: ≤2 V
Response time: 140 µs 200 µs
Switching frequency: 3.5 kHz 2.5 kHz
Emission type: RED LASER (λ= 645…665nm): Class 2 EN 60825-1 (1994), Class II CDRH 21 CFR PART 1040.10
Pulsed emission: pot. max ≤5mW; pulse duration = 5µs; frequency = 14KHz (mod. M01) / 10KHz (mod. M11)
Focalisation point : 60 mm 150 mm
Spot dimension: < 0.2 mm (at 60 mm) < 0.4 mm (at 150 mm)
Operating distance (typical values): 30…150 mm 50…350 mm
Adjustment: 4 turns distance adjustment trimmer 6 turns distance adjustment trimmer
Difference (90% white/ 4% black): < 4 % (see DETECTION DIAGRAM)
Hysteresis (90% white): < 1 %
Indicators: OUTPUT LED (YELLOW) / POWER ON LED (GREEN)
Functioning temperature: -10 … 55 °C
Storage temperature: -20 … 70 °C
Insulating strength: 500 Vac 1 min., between electronics and housing
Insulating resistance: >20 MΩ500 Vdc, between electronics and housing
Ambient light rejection: According to EN 60947-5-2
Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for each axis (EN60068-2-6)
Shock resistance: 11 ms (30 G) 6 shock for each axis (EN60068-2-27)
Housing material: ABS
Lens material: PMMA window; PC lens
Mechanical protection: IP67
Connections: M12-4 pole connector
Weight: 40 g. max.
SETTING
Suppression distance setting
1.Object detection
Position object to detect in front of the sensor at the distance required.
Turn distance adjustment trimmer (ADJ) to minimum: yellow LED OFF and
green LED ON.
Rotate trimmer in a clockwise direction until the yellow LED and green LED
turn ON. Object detection condition (A status of position indicator).
A
2.Background suppression
Remove object and ensure that the background is in front of the sensor:
yellow LED OFF and green LED ON.
Rotate trimmer in a clockwise direction until the yellow LED and green LED
turn ON: background detection condition (B status of position indicator).
B
The trimmer reaches maximum level with yellow LED OFF if the background
is outside the operating range.
Rotate trimmer in an anticlockwise direction until yellow LED turns OFF
and green LED ON: condition where background is outside operating
range (C status of position indicator).
C
3.Setting and control
Rotate trimmer in an anticlockwise direction until the indicator reaches
an intermediate point between position A and C.
If position A and C are close to each other, leave trimmer on position C.
The sensor is now ready to function correctly and in stable conditions.
DETECTION DIAGRAM
DIMENSIONS
4.7
mm
Ø15
16
M12
18x45°
18
DISTANCE ADJUSTMENT TRIMMER
POSITION INDICATOR
20.75
50
42
18.4
POWER ON LED
OUTPUT LED
10.7
11
6.18
11
614
50
42
1.1
EMITTER
RECEIVER
18.215.5
SAFETY PRECAUTIONS
All the electric and mechanical safety regulations have to be respected during
sensor functioning.
The sensor has to be protected against mechanical damage.
Apply the labels supplied in a visible position near the laser emission beam.
Do not stare directly into the laser beam!
Do not point the laser beam towards people!
Eye irradiation superior to 0.25 seconds is dangerous. Please refer to the
Class 2 Standard (EN60825-1).
These sensors can not be used for safety applications!
EX-II-3-D T6
Temperature class:
T6 (<85°C)
Max. Power consumption: 800 mW at 30 Vdc
Max. Internal capacitance: 100 pF
Internal inductance: negligible
DECLARATION OF CONFORMITY
We DATASENSOR S.p.A. declare under our sole responsibility that these products are conform to the
2004/108/CE, 2006/95/CE Directives and successive amendments.
WARRANTY
DATASENSOR S.p.A. warrants its products to be free from defects.
DATASENSOR S.p.A. will repair or replace, free of charge, any product found to be defective during the
warranty period of 36 months from the manufacturing date.
This warranty does not cover damage or liability deriving from the improper application of
DATASENSOR products.
DATASENSOR S.p.A. Via Lavino 265
40050 Monte S. Pietro - Bologna - Italy
Tel: [phone] Fax: [phone]
http://www.datasensor.com e-mail: [e-mail]
DATASENSOR S.p.A. cares for the environment: 100% recycled paper.
DATASENSOR S.p.A. reserves the right to make modifications and improvements without
prior notification.
826003241 Rev.B