Datatronics JB7210 Series User manual

Operation Manual
JuniBox Automated Disc Duplicator
Model #: JB7210 Series (Standalone)
Serial Number: ______________________________
(The serial number is labeled on the rear panel of the device.)

Operation Manual, JuniBox JB7210 Version 1.1F
PREFACE
Important Safety Instructions
For your safety, basic precautions should always be followed to reduce
risk of damage, electric shock, fire, and personal injury. This includes
the following:
Read this manual carefully and follow all warnings and
instructions.
Operate the unit with only the proper electrical specifications as
labeled on the device. Use only 3-wire extension cords that have
3-prong grounding plugs and 3-pole grounding receptacles that
accept your device's plug. Make sure the device is connected to
a known ground.
Do not expose this unit to direct sunlight, rain, moisture, water,
flammable material, gas, dust, dirt, smoke, pollution or abrupt
humidity changes.
Place this device on a steady level surface in an air-conditioned
environment with sufficient ventilation. Do not move this device
while the power is on. Handle with care.
This device generates heat during the duplication process.
Out-of-specification or unstable power supply may cause
overheating, low productivity, increased failure rate, and damage
to the device.
Use a reliable power source with correct voltage and ample
current supply. Give this device a dedicated power outlet. Do
not share the outlet with other devices.
Please make it a habit to always unplug the power cord before
troubleshooting or performing maintenance. Always turn the
power switch to the Off position when connecting the power cord.
Do not attempt to disassemble this device or touch any of the
moving parts. Refer servicing to qualified service personnel.
Unauthorized disassembly or repair will void all warranty.
Acknowledgments
© 2008, Datatronics Technology Inc. All rights reserved.
Notices: Reproduction, adaptation, or translation without prior written
permission is prohibited.
Trademarks: Datatronics, JuniBox, GetTray, BoxWriter, MiniCubis,
and Pronto are the trademarks of Datatronics Technology Inc. All
2 © 2008, Datatronics Technology, Inc.

Version 1.1F Operation Manual, JuniBox JB7210
other products, brands, and trademarks are the property of their
respective owners.
FCC Compliance: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. In a domestic environment this product may cause
radio interference, in which case the user may be required to take
adequate measures.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician.
Use of shielded cables is required to comply with the Class A limits of
Part 15 of the FCC Rules. You are cautioned that any changes or
modifications not expressly approved in this manual could void your
authority to operate and/or obtain warranty service for this equipment.
Limited Warranty (North America): The information contained in this
document is subject to change without notice. Datatronics
Technology Inc. makes no warranty of any kind with respect to this
information.
Datatronics Technology Inc. guarantees this device for a period of one
year from the date of delivery, free from defects in material and
workmanship. In case of malfunction or fault, Datatronics Technology
Inc. will, at its option, repair or replace the product.
You must return the defective product, protected in the original
packaging, with a valid RMA number, to an authorized dealer or
reseller within the warranty period accompanied with the proof of
purchase.
This warranty only covers parts made by Datatronics Technology Inc.
For parts made by other manufacturers, such as hard disks, and disc
© 2008, Datatronics Technology, Inc. 3

Operation Manual, JuniBox JB7210 Version 1.1F
recorders, the original manufacturer’s warranty applies.
This warranty will not cover abuse, misuse, alteration, modification,
tampering, negligence, faulty installation, accidents, lack of reasonable
care, unauthorized repairs or service, or if installed to any device not
provided with the product, or if the serial number label provided with
this product has been broken or removed.
This warranty does not cover damages that occur in shipment, due to
acts of God. All repairs and replacement services shall only be
handled by Datatronics Technology Inc, and by authorized service
centers. Parts used for replacement are covered only for the
remainder of the warranty period.
Datatronics Technology Inc. disclaims all implied warranties on this
product, including without limitation warranties of merchantability,
performance, and fitness for a particular purpose.
In no event will Datatronics Technology Inc. be liable for direct,
indirect, special, incidental, tort, economic, contingent or consequential
damages resulting from any defect in this product or its documentation,
including, without, limitation, damages or costs relating to the loss of
data, profits, business or goodwill, even if Datatronics Technology Inc.,
its authorized dealers or resellers have advertised the possibilities of
such damages. In no case shall Datatronics Technology Inc.’s
liability exceed the amount paid by the user of this product out of which
such claim arose.
Any written or oral information or advice given by the dealer, reseller,
agent, sales representative, or employee of Datatronics Technology
Inc. will in no way increase the scope of this warranty nor should you
rely on such oral or written communication.
Technical Support: For technical support and assistance, please
contact your local dealer.
For additional information regarding optical disc duplication, printing,
and management please visit our website. We value your comments
and suggestions and thank you for your purchase.
Datatronics Technology, Inc.
http://www.datatronics.com.tw
4 © 2008, Datatronics Technology, Inc.

Version 1.1F Operation Manual, JuniBox JB7210
Table of Contents
Preface 2
Specifications 6
Unpacking Your JuniBox 7
Package Contents......................................................................... 7
Getting Familiar with JuniBox 9
Block Diagram............................................................................... 9
A Look at JuniBox......................................................................... 9
Rear View.................................................................................... 10
Control Panel.............................................................................. 10
LED Indicators .............................................................................11
Device Installation 13
Finding a Place for JuniBox........................................................ 13
Using the Detachable Legs......................................................... 13
JuniBox Installation..................................................................... 13
Before Getting Started 15
Tips for Handling Optical Discs................................................... 15
What You Need to Start a Disc Duplication Session................... 15
Important Tips for Loading Discs to JuniBox .............................. 15
Rejected Discs............................................................................ 15
More Than 30 Discs in One Session.......................................... 16
Automated Multiple-Master-Disc Duplication.............................. 16
Write Speed: Production Rate vs. Duplication Quality................ 17
Duplicate Disc Verification .......................................................... 17
Handling Disc Write Failures....................................................... 18
Turning JuniBox On .................................................................... 18
Turning JuniBox Off .................................................................... 18
Operation Quick Guide 20
Abort a Running Operation......................................................... 20
Start a Duplication Session......................................................... 20
Duplication Simulation ................................................................ 21
Erase a Stack of Rewritable Discs.............................................. 21
Verify a Stack of Discs ................................................................ 22
Appendix 23
JuniBox Maintenance.................................................................. 23
Choosing Reliable Blank Discs................................................... 23
Disc Separation........................................................................... 23
The Quality of the Master Disc Counts....................................... 24
Writing Speed.............................................................................. 24
Frequently Asked Questions 25
© 2008, Datatronics Technology, Inc. 5

Operation Manual, JuniBox JB7210 Version 1.1F
SPECIFICATIONS
Disc Recorder One CD/DVD recorder (JB7210);
One Blu-ray/CD/DVD recorder (JB7210-BR)
Input Capacity: 30 discs; 100 discs or more using extension
rods (increased capacity using non-stop refill)
Output Capacity: Dependent capacity (completed discs are
placed in front of the unit, in a separate
container, or Disc Storage Bin)
Reject Disc Capacity: 3 discs without legs; 30 discs using legs
Write Speed: CD-R: 40X; CD-RW: 32X;
DVD±R: 18X; DVD±R Dual: 10X;
DVD-RW: 6X; DVD+RW: 8X
Blu-ray: 4X (JB7210-BR)
Operation Method: Standalone; PC connection is not required
Control Panel: High-Speed, Safe-Speed, Function,
Test/Abort; with corresponding LED
Indicators
Disc Size: 120 mm in diameter
Operation Temperature: 42℉to 86℉(6℃to 30℃)
Humidity: 5% to 85%, no condensation
Certification: CE and FCC; power adaptor is UL approved
Dimensions: 7-3/4" x 8-1/2" x 15-3/8"; 19.5 x 21.3 x 39 cm
Weight: 2.7 kg; 6 lbs (varies upon configuration)
Power: 100 to 240VAC; 50 or 60 Hz
*Specifications are subject to change without notice.
6 © 2008, Datatronics Technology, Inc.

Version 1.1F Operation Manual, JuniBox JB7210
UNPACKING YOUR JUNIBOX
Congratulations on purchasing the JuniBox JB7210 (Standalone)
Automated Disc Duplicator. JuniBox is a state-of-the-art, automated,
optical disc duplicator, which does not require a PC connection to
operate. It is an integrated system with a built-in single optical disc
recorder, a hard disk and autoloaders. The embedded controller and
built-in hard disk provide an extremely reliable automated, standalone,
duplication solution.
JuniBox has a 30 disc capacity, which can be increased to 100 or more
using storage extensions, and an enclosure that protects discs from
dust. It can also detect faulty discs and separate them from a
duplication session. Depending on the configuration of your device
during purchase, it may come with a CD/DVD or Blu-ray recorder
(JB7210-BR).
Getting JuniBox up and running is simple. The control panel with LED
indicators and operation buttons takes minutes to learn. Simply
connect the power cord, turn the power switch to the On position, load
the master and blank discs into the disc loader, and press the desired
duplication speed button.
Please read this manual carefully before using JuniBox. This user guide
contains all the information on its operation and maintenance. For
additional information regarding optical disc duplication, printing, and
management please visit our website. We value your comments and
suggestions and thank you for your purchase.
Package Contents
Before opening the package, carefully inspect for any damage. If
there is any sign of damage, contact the shipping company and your
local dealer immediately.
Save the packing materials in case you need to ship or return your
product. The original packaging will ensure the product is protected
during transportation. Returning goods without the original packaging
may not protect the product during transportation, and will void your
warranty.
Once you have removed all the parts included with your package,
please check to see if any pieces are missing or damaged. If any part
is missing or damaged, contact your local dealer immediately.
© 2008, Datatronics Technology, Inc. 7

Operation Manual, JuniBox JB7210 Version 1.1F
The items listed below should be included in the package:
One JuniBox JB7210 Automated Disc Duplicator
One power cord
One power adapter
One spindle box (serves as the Finish Disc Bin)
Three Extension Rods (attached to the underside of JuniBox's lid)
One Alignment Pad
Four Legs
One operation manual
8 © 2008, Datatronics Technology, Inc.

Version 1.1F Operation Manual, JuniBox JB7210
GETTING FAMILIAR WITH JUNIBOX
Block Diagram
JuniBox JB7210 is an integrated system with a single optical disc drive,
hard disk and autoloader. See the illustration below.
Depending on the configuration of your purchase, your JuniBox may
come with one of the following optical disc recorders:
JuniBox JB7210: CD/DVD recorder
JuniBox JB7210-BR: Blu-ray/CD/DVD recorder
A Look at JuniBox
The figure to the right
shows JuniBox with a
spindle box in front of it
to collect and stack
finished discs.
Lid (Blank Disc
Storage)
Open the lid to
access the blank
disc storage area.
Control Panel
Located on the top
front of JuniBox, the
control panel
© 2008, Datatronics Technology, Inc. 9

Operation Manual, JuniBox JB7210 Version 1.1F
contains the LED indicators and operation buttons.
Legs
Use the four legs included with your JuniBox to provide space
underneath for rejected discs.
Reject Disc Slot
The rejected discs will slide out from the Reject Disc Slot at the
bottom of the unit. Always allow space beneath JuniBox to
accommodate rejected discs.
Finish Disc Slot
Finished discs will exit from this slot.
Finish Disc Bin
This bin serves as the storage container for receiving and
stacking completed discs. As illustrated, a spindle box serves
as a good Finish Disc Bin.
Alignment Pad
Use the pad to appropriately position the Finish Disc Bin under
the Finish Disc Slot.
Rear View
Power Socket
Use the provided power cord
to connect JuniBox to a wall
outlet.
Power Switch
Turn JuniBox on and off.
Ventilation
This allows heat to escape.
Do not block this otherwise the
unit may overheat.
Kensington Security Slot
Security lock anti-theft system.
Control Panel
There are operation buttons and
LED indicators on JuniBox’s control
panel as illustrated to the right.
High-Speed Duplication
Press to start the duplication
10 © 2008, Datatronics Technology, Inc.

Version 1.1F Operation Manual, JuniBox JB7210
process at the highest possible
write speed to produce discs at the maximum production rate.
Safe-Speed Duplication
Press to start normal speed duplication. This increases quality but
decreases output rate. Recommended for audio and video discs.
Function Key
Press this button to activate or deactivate disc verification during
the duplication process.
Test/Abort
Press to abort the current duplication process or to start a
duplication simulation.
Important:
The High-Speed Duplication mode will use the maximum
recorder speed but may be limited by the write speed of the
disc.
LED Indicators
JuniBox’s status is reflected by the LED indicators. When turned on,
it will enter initialization indicated by a flashing green ready light.
When initialization is complete, the ready light will change to steady
green. The table below describes the meanings of the LED
indicators.
H S F T Description
zzzzThe power switch is in the Off position
ÖÖÖÖDevice Initialization
zzz{Ready Mode
zz{High-Speed Duplication
zz{Safe-Speed Duplication
z{{High-Speed Duplication with Disc Verification
z{{Safe-Speed Duplication with Disc Verification
zz{Disc Verification in progress
ÖÖÖ{Erasing rewritable disc
zzzError Encountered
zz{zFunction Key Enabled
{: Lit z: Off : Flash Ö: Running
© 2008, Datatronics Technology, Inc. 11

Operation Manual, JuniBox JB7210 Version 1.1F
(This page is intentionally left blank.)
12 © 2008, Datatronics Technology, Inc.

Version 1.1F Operation Manual, JuniBox JB7210
DEVICE INSTALLATION
Finding a Place for JuniBox
JuniBox should be placed on a fairly level surface, firm enough to
support the unit and discs. Always allow ample workspace for your
operation, with easy access to the blank and finished discs.
Do not expose the unit to direct sunlight or high humidity, as it may
cause the unit to malfunction.
If you desire, JuniBox can be placed on a raised block so there is
ample room to receive discs from the Finish Disc Slot. Please refer to
the “More Than 30 Discs in One Session” section for details.
Using the Detachable Legs
JuniBox is designed to work either with or
without detachable legs. Without the legs,
the Reject Disc Slot (recession) on
JuniBox’s base will hold up to 3 rejected
discs.
If your application doesn’t involve rejected
discs or separating a group of discs from
others, you may use JuniBox without the
legs. It is, however, recommended to use
the legs when possible.
The legs will raise JuniBox providing
sufficient room to accommodate additional
rejected discs, as well as easier access to
them beneath the unit.
Attaching legs to JuniBox is simple. Inserting one leg after another on
JuniBox’s base, match the leg to JuniBox (AtoA’) and gently snap the
leg into the receptacle (B to B’) until it is firmly attached.
To remove the legs, gently press the notch (N) and pull it outward from
the receptacle (B’).
JuniBox Installation
Follow the steps below to complete JuniBox’s hardware installation:
1) Place JuniBox on level surface so that it stands firmly on its legs.
2) Place the spindle box that came with the unit in front of JuniBox.
© 2008, Datatronics Technology, Inc. 13

Operation Manual, JuniBox JB7210 Version 1.1F
Use the alignment pad to appropriately position the spindle box
under the Finish Disc Slot.
3) Use the power cord that came with the unit to connect JuniBox to
a wall outlet with a reliable power supply.
You have now successfully completed the installation of JuniBox
device.
14 © 2008, Datatronics Technology, Inc.

Version 1.1F Operation Manual, JuniBox JB7210
BEFORE GETTING STARTED
Tips for Handling Optical Discs
Never touch the printable or data surface of the disc, as it may
decrease quality and disc lifespan. Refer to the arrows on the
illustration to the right, Always handle discs from the outer edge or the
center hole.
What You Need to Start a Disc Duplication Session
The JuniBox JB7210 is a standalone duplicator, which does not require
a computer connection. You will need the following to start a
duplication session:
Master Discs
The original disc providing the source of data for a duplication
session.
Blank Discs
The disc that JuniBox will write the source
data to during a duplication session.
Important Tips for Loading Discs to JuniBox
When the disc loader is empty, do not attempt to
load many discs at once.
First, carefully load only one disc into the disc
loader and assure it is firmly resting on the three
wheels seen in the illustration to the right. You
may then gradually load additional discs on top of
the first disc, until the loader is full.
JuniBox processes discs in a First In, First Out (FIFO) sequence.
During a duplication session, if a disc refill is required, before the
loader becomes empty, gently load additional discs.
Rejected Discs
JuniBox is designed to have Rejected
Discs come out underneath the unit. Do
not block the Reject Disc Slot.
Periodically remove rejected discs so that
there is room to accommodate more discs
or raise JuniBox using the provided legs to
© 2008, Datatronics Technology, Inc. 15

Operation Manual, JuniBox JB7210 Version 1.1F
increase space underneath for more discs.
Important:
JuniBox will stop operation if a rejected disc cannot clear
the Reject Disc Slot.
More Than 30 Discs in One
Session
Using the extension rods, JuniBox
can process 100 or more discs
without refilling. To increase
JuniBox’s capacity to 100 discs,
please follow the instructions below:
1) Open the Blank Disc Storage
Lid.
2) Remove the extension rods
from the lid’s underside.
3) One after another align the rods into the three holes on the disc
loader, then, gently turn the rods counterclockwise to make sure
they are firmly attached;
4) Use a suitable box to raise JuniBox approximately 96 mm high to
account for the output of 100 or
more discs.
5) Use the alignment pad to
appropriately position the Finish
Disc Bin below the Finish Disc
Slot. The Finish Disc Bin may
be a spindle box or a container
with enough depth to
accommodate 100 or more
discs in a session.
Since JuniBox is equipped with a FIFO (First-In-First-Out) disc loader,
you may simply refill discs before the disc loader becomes empty.
This will allow an unlimited number of additional discs to be processed
in one session, as long as the Finish Disc Bin is continually emptied.
To remove the extension rods from the disc loader, turn the rods
clockwise and pull them upward vertically. When not using the rods,
return them to their original position on the lid’s underside.
Automated Multiple-Master-Disc Duplication
JuniBox not only performs one-to-multiple, but also multiple-to-multiple
16 © 2008, Datatronics Technology, Inc.

Version 1.1F Operation Manual, JuniBox JB7210
disc duplication. Whenever JuniBox detects a non-blank disc in a
recorder, a disc image will be written to the built-in hard disk. The disc
image is then used to duplicate all the following blank discs, until
another master disc is detected or the loader becomes empty.
When another non-blank disc is detected, a new disc image will be
written to the built-in hard disk. The previously stored image will be
overwritten and the new image will be used for disc duplication.
Do not use rewritable discs as a master disc, since JuniBox is
designed to always erase rewritable discs before attempting to write
data to them.
Write Speed: Production Rate vs. Duplication Quality
By pressing the appropriate button, JuniBox can perform High-Speed
and Safe-Speed Duplication accordingly. High-Speed Duplication
writes to discs at the highest possible speed according to the recorder
and blank disc characteristics.
Although High-Speed Duplication takes less time to write to a disc, and
produces more discs per hour than Safe-Speed Duplication, a higher
failure rate may be encountered, especially when the blank disc quality
is not good.
Most users choose High-Speed Duplication, while professional users
prefer Safe-Speed to duplicate audio and video discs, for improved
duplicate disc quality.
When duplicate disc quality is critical, activate the Verify Disc mode to
have JuniBox read and verify each duplicate disc with the source
image immediately after the disc is duplicated.
Duplicate Disc Verification
JuniBox is not only able to verify each duplicate disc with the source
disc image during a duplication cycle, it can batch verify a stack of
discs with a master disc. Duplicate disc verification involves reading
and comparing the duplicate disc image with the master disc image on
the hard disk.
Disc verification is performed according to the disc data format. For
data disc verification, both the read and comparison process will be
performed. However, due to the limitation of industry standards, for
audio disc verification it will only perform the reading check, and not
the comparison process.
© 2008, Datatronics Technology, Inc. 17

Operation Manual, JuniBox JB7210 Version 1.1F
Handling Disc Write Failures
Some discs may be defective and fail during a write session. A failed
disc will be sent to the Reject Disc Slot.
To avoid excessive disc failure, JuniBox is designed with the following
rules when disc failure is encountered:
In a normal duplication session if the recorder continuously fails to
write to ten discs in sequence, this recorder will be deactivated.
JuniBox will halt the active duplication session and the LED
indicator status will show an error.
To resume operation from an error, carefully check for and resolve any
noticeable problems, press the button for the desired duplication speed
to resume the session.
Important:
In case JuniBox has been turned off, always wait for 30
seconds before turning it back on. Then, reload the master
and blank discs and press the appropriate button to start a
new job.
Turning JuniBox On
Follow the steps below to get your JuniBox ready:
1) Connect the power cord to JuniBox and a wall outlet.
2) Turn JuniBox’s power switch to the On position.
JuniBox will enter the initialization process and will remove any discs
inside the optical recorder. Be patient until the initialization process
has completed.
When initialization is complete, you willsee the“ready” indicator light up
signaling that JuniBox is ready for a disc operation
Turning JuniBox Off
To turn JuniBox off, turn the power switch to the Off position. In case
there is a duplication session underway, abort or wait until it has
completed.
Although it is fine to leave the power cord plugged in, it is
recommended that you unplug the cord for increased safety when
JuniBox is not used for extended periods of time.
18 © 2008, Datatronics Technology, Inc.

Version 1.1F Operation Manual, JuniBox JB7210
(This page is intentionally left blank.)
© 2008, Datatronics Technology, Inc. 19

Operation Manual, JuniBox JB7210 Version 1.1F
OPERATION QUICK GUIDE
Abort a Running Operation
To abort a duplication session, press the Test/Abort
button. If the recorder is currently writing to disc,
JuniBox is designed to abort the duplication session
after the recorder has completed writing to disc.
Important:
Turning the power switch to the Off position will
immediately terminate the active duplication session, damaging
any disc in the process of being written to. Only turn off the
power in case of emergency.
Start a Duplication Session
High-Speed Duplication produces more discs per hour, yet Safe-Speed
better assures duplicate disc quality especially for audio and video
discs.
Follow the steps below to start a one-to-multiple disc duplication
session:
1) Load the master disc into the disc
loader.
2) Load the desired quantity of blank
discs on top of the master into the
disc loader.
3) Press either the High or Safe-Speed
Duplication button to start.
JuniBox will run the operation until
the disc loader is empty.
Important: mode whenever a rewritable
use
r written data, press the D
In duplication
disc is detected, JuniBox is designed to
always erase the disc. Do not use
rewritable discs as master discs beca
the data on the disc will be erased.
Important:
To verify you
Function Key which will light up its LE
20 © 2008, Datatronics Technology, Inc.