Disc Makers ReflexAuto 8 User manual

1
Chapter 1: Overview
1. Welcome
The Disc Makers ReflexAuto autoloader is a reliable, high performance, high speed, standalone, robotic
DVD and/or CD autoloader. With its profes sional industrial design and simple user interface, it makes your
duplicatin g experience easier than ever.
With the Disc Makers ReflexAuto, you can have a capacity from 100 to 1000 discs, duplicate continuously
for 24 hours (even with multiple masters), and get the highest quality duplication, all at an extremely
affordable pric e. The Disc Makers ReflexAuto is the most reliable and affordable autoloader on the market.
Before you start using this autoloader, please read the following to ensure proper operation:
DVD Duplication Limitations
The DVD autoloader will not copy any DVDs that have Copy Protection en coded in the content. Typically,
most DVDs you purchase or rent from a store contains Copy Protection.
In addition to the copy protection limitation, the autoloader will only copy a DVD5 format (4.7 GB) disc to
another DV D5 format recordable DVD media. If your autoloader has double layer/dual layer capability, you
can copy a DVD9 format (8.5 GB) disc to another DVD9 format recordable DVD media, but you cannot
duplicate a DVD5 format disc on to a DVD9 format recordable medi a or vice versa.
Temperature Warning
If the autoloader was stored in a location where the temperature dropped be low 32° F (0° C) within the past
24 hours, leave the autoloader in a warm room with temperatures at least 65° F (19° C) for four hours prio r
to powering it on for the first time. Failure to do so may cause irreparable harm and prevent the autoloader
from functioning.
Maintenance
It is very important to operate and keep the autoloader in a dust free, clean en vironment since dust is the
nu mber one killer of CD/DVD recording devices. Failure to do so can severely damage your autoloader. We
strongly suggest that you constantly use an Air Duster (Canned Air) to clear off any dust on the surface of
the autoloader.
Note: Do not try to use an A ir Duster to clean the autoloader while the writer trays are open. In doing so, you
may inadvertently blow dust into the recording device and damage it.
Proper Shutdown
To avoid possible system failures, you need to shut down the autoloader prop erly. To shut down the
autoloader use the Shutdown hot key and follow the instructions on the screen. Not performing this
function increases the risk of damaging the autoloader.

2
Double Layer/Dual Layer Partition Issue
If you have a 16x speed or higher autolo ader with double layer/dual layer DVD9 capability, the hard drive
partitions are set to a default size of 9 GB each to accommodate for the expanded size of the DVD9 format.
If you re quire more partitions and do not plan on using double layer/dual layer DV D9 media, you can reduce
the size of the partitions using the instructions given in Partition Size on page 26. Keep in mind that if you
alter the partition size, all previous data/video stored on the hard drive will be lost and you will only be able
to l oad media with less than 5 GB capacity such as DVD5 (4.7 GB), CD (700 MB), etc.
Disc Static and Sticky Media Issues
The most common problems when using an autoloader are the disc stat ic and sticky media issues. These
static charge problems cause multip le discs to stick to gether, resulting in improper operation and more
severely, can shocks the robotic arm while loading a disc that causes system freeze due to heavy static
charge. Even though the autoloader has a sticky media separator function to preven t the sticky media, but
you should still follow these steps to prevent sticky media from disrupting your operation and protect your
system from disc static charge.
This issue is most commonly seen when you buy a 100 pack of blank discs and insert them in to the
autoloader without any treatment. If you have expe rienced this kind of problem, please do the following to
remove the adhesive static between the discs:
Separate the blank discs before you place them into the autoloader's spindle(s). Separating t hem
will greatly reduce the static between discs.
If this doesn't achieve the desired outcome, use an air duster (canned air) to blow air around the
circular edge of the blank discs. This process reduces the static between the discs up to 90%. The
amount of air to use depends on factors specific to your environment.
Figure 1 - 1 Using Canned Air to Reduce Static
If you are still having problems, put your media into the refrigerator (NOT in the freezer) for three
hours. Afterwards, store it at room tem per ature for one hour prior to use. Studies show that cold
temperature (with no condensation) will also reduce the static charges between objects
dramatically.

3
Disc Placement Issue
Another common problem when using an autoloader is the placement of med ia onto the spindles. Placing
the media onto the spindles properly can avoid possible picking errors when operating the autoloader. Even
though the autoloader is designed with certain tolerance adjustments to prevent mishandling by the picking
arm, failure s may still arise if the spindles are not loaded correctly. All media loaded onto the spindles
should be flat and not slanted at an angle to ensure the picking arm can securely grab the disc with all 3
vacuum suction heads. Be sure to not load too many di scs onto the spindle as well as this may cause errors
in placement and loading. The diagram 1 - 2 below demonstrates the proper and incorrect disc placements
when loading media onto the spindles.
Figure 1 - 2 Disc Placement Illustration
Spindles vs. Bins
The Disc Makers ReflexAuto has up to 5 spindles for holding CDs and/or DVD s. Although the manual
refers to them as spindles, many of the messages shown on the LCD display refer to them as bins in order
to create more concise mes sages. Don t panic. Spindles and bins are the same.

4
2. The Robotic Platform
The Disc Makers ReflexAuto autoloader (with 1000 Disc Capacity) has five spin dles (see Figure 1 - 3) that
hold approximately 250 discs each.(Actual quantity varies depends on the media thickness) Initially Spindle
1 is empty. The robotic arm picks blank discs from Spindle 2 first, and places the success ful copies onto
Spindle 1. Once Spindle 2 is empty, it picks blank discs from Spindle 3, and places the successful copies
onto Spindle 2. It then p icks from Spindle 4 and places onto Spindle 3, and then picks from Spindle 5 and
places onto Spindle 4. Reject discs are placed on to the deck below the drive trays. (Throughout this
manual, this area is also referred as Reject Area )

5
3. The LCD Contr ol Panel
Figure 1-4 below shows the LCD Control Panel. This panel has a two-line by 20 character LCD display to
provide user feedback and eight push buttons to control the of the Disc Makers ReflexAuto operation. The
functions for these buttons are shown in Table 1 - 1.
Figure 1 - 4 LCD Control Panel Layout
Table 1 - 1: Front Panel Controls
Control Name Function
Up Scroll up through the menu or list.
Down Scroll down through the menu or list.
Enter Execute the function. Also called OK i n the Menus.
ESC Go back to the previous function.
Master
Master Quick Key to put machine in the correct Master Mode.
Load
Load Quick key to load a master disc to the units internal hard drive
Info
Info
Quick key to see system, master disc, and hard drive image information
including partition size, disc size, disc type, drive and system firmware versions .
Shutdown
Shutdown
Quick key to properly turn off the unit.

6
4. Menu Overview
This section provides an overview of the menu options. These menu options are explained in detail on the
referenced pages.
1. Copy page 14
Use the Copy menu to make copies of a master disc or hard drive image . Before you start a copy,
make sure you have selected the correct Master Mode .
If you plan to use Single Master Mode, please make sure you have successfully loaded your master
disc to a partition on the Hard Drive.
If you plan to use Multi Master Mode, please make sure you have placed every master disc on top
of the corresponding number of blank discs.
For additional information, see Making Copies in Single Master Mode on page 14 or Making
Copies in Multi Master Mode on page 16.
2. Test page 18
Use the Test menu to simulate the copy process. With si m ulation, write once recordable discs such
as DVD - R, or CDR will be reusable. The purpose of simulation is to ensure error free duplication.
Note: Due to physical limitations of the DVD+R recordable format, you can not test or simulate
the DVD+R copy f ormat.
Warning : If you are using CD/DVD Rewritable discs as your blank media during the simulation, the
content on those discs will be permanently erased.
3. Compare page 19
Use the Compare function to perform a bit - by - bit compari son between the content of your master
disc(s) in the Hard Drive and the contents of all discs it copied. This ensures that all of your copies
are identical to original master disc(s).
Note: The bit - by - bit comparison will only apply on all DVDs and Data CDs. The readability check
will be applied for other formats like Audio CDs, CD+G, and Video CDs discs due to their
lack of error correction mechanisms.
4. Test + Copy page 20
Use the Test + Copy menu option to simulate the copyin g process initially. Then, the autoloader
performs the actual copy process on the blank disc(s) that passed the simulation. For the blank
disc(s) that didn t pass the simulation, the autoloader will place it/them to the Reject Area.
5. Copy + Compare page 20
Use the Copy + Compare menu option to make 100% reliable copies. After the copy process is
done, the autoloader automatically compares the copies from the content of your original master
disc.
6. Select Burn Speed page 21
Use the Select Burn Speed menu option to adjust the duplication speed for the various blank disc
formats. For additional informa tion, see Select Burn Speed on page 21.

7
7. Select Source page 22
Use the Select Sourc e menu to tell the system where the content of the master disc resides during
duplication. At this point, Hard Drive is the only place where the content of the master disc resides
during duplication. For additional information, see Select Source on page 22.
8. Master Mode page 22
Use the Master Mode menu to select either Single Master Mode(SM) or Multi Master Mode (MM).
For more information on those modes, see Single Master and Multi Master Modes on page 10.
For more information o n using the Master Mode menu, see Master Mode on page 22
9. Erase RW page 22
Use the Erase RW menu to erase your Rewritable discs. There are two options:
Full Erase: This option erases the entire disc, destroying all previously written data in the
process.
Quick Erase: This option erases the index (TOC) of the Rewritable disc, not the data
section. It is much faster than Full Erase. However, the data section is still recoverable. If
you prefer the old content not to be recovered for security purpose, please perform Full
Erase.
10. Hard Drive Setup page 24
Use the Hard Drive Setup menu to perform various hard drive - related opera tions. These options
include loading, renaming, or deleting your images. For addi tional information, see Hard Drive
Setup on page 24.
11. Setup page 27
Use the Setup menu options to control how the autoloader operates. You can scroll between the
various options using the Up or Down button.
1. Language
Use this setting to choose the language used to navigate the autoloader. The autoloader
supports English and Span ish menus.
2. Read Error Skip
Normally, when the autoloader encounters a read error while reading the master disc, all
the duplication will be aborted and all the recordable media in the writers will be ruined.
However, if you believe that your master disc has a small, insignificant error due to physical
damage, you can enable this setting to allow the autoloader to skip any read errors that it
encounters. It is ON by default.
Important: This function does not fix the error; it only skips it to continue copying the rest of
the readable data. This function is recommended for Video and Audio duplication purpose.
3. CD Writing Mode
Use this setti ng to select the mode you would like use to duplicate a CD. There are two
different modes: Disc at Once and Track at Once. Disc at Once is recommended for
duplication .
4. Max Audio, VCD & CDG Speed
Due to the lack of error checking mechanism for Audio C D, Video CD and CD+G format,
duplicating them at too high a speed can cause frequent errors like glitches and skips. Use
this setting to adjust the maximum duplication speed for Audio, Video CD and CD+G
format to ensure the reliable duplication for such fo rmats.

8
5. Buzzer
Use this setting to choose whether you want to hear a beep when you press a button and
when a task has been completed.
6. Startup Menu
Use this setting to choose which menu you would like to see first when you turn on the
autoloader.
7. Screen Saver
Use this setting to enable or disable the Screen Saver feature. When this is en abled, a
screen saver is displayed whenever your autoloader has been idle for a long period of time.
8. Counter
Use the Counter menu to enable or disable the Counter feature. The counter tells you how
many discs have been copied and how many discs are left to go during the progress and it
will stop the job once the desired number of copies has been made.
9. AUTOCOPY Enabled
This menu option turns on the hi dden 16.AUTOCOPY main menu op tion. The AUTOCOPY
function simplifies the copy process by allowing you to stack blank media on a spindle(s),
place the master on top of the stack on the first spindle, and press the Enter button on
16.AUTOCOPY key in the main menu. It will load the content of the top disc of the 1
st
input
spindle (master disc) into the Reserved Partition of the Hard Drive and copy it to blank
disc(s) below it and other input spindle(s) if exists.
10. DVD+R Compatibility Mode
This feature all ows you to turn the DVD+R High Compatibility Mode feature ON or OFF.
The purpose of this feature is to increase the com patibility of DVD+R media with a broader
range of DVD Video play ers.
11. Disable Drives
Use this utility to allow the system to disab le certain drives/trays when certain drives/trays
are producing high failure rates. See Disable Drives on page 32.
12. System Utilities page 33
1. Disc Info
Use the Disc Info utility to identify the type of blank recordable medi a. This utility identifies
your blank recordable Media's format, capacity, manufacture ID, and the Media's certified
writing speed.
2. System Info
Use this menu option to see data about the autoloader and its resources (firmware version,
RAM and CPU).
3. Device Info
Use this menu option to see data about the drives that are installed in the autoloader.
4. Load Default
Use this menu option to reset all of the options back to the manufactur er's default values.
You can use this function if your autol oader is acting abnormally.
5. Update Firmware
Use this utility to update the software in your autoloader. To update, in sert the
manufacturers Certified Update CD into the 1
st
tray and make sure no other discs are in
rest of the trays. Then you can pr ess the Enter button to update.

9
Important: You should not upgrade your autoloader's firmware unless your system is
becoming unstable or you are advised to do so by Tech Support.
13. Loader Utilities page 36
Use the Loader Utilities menu options to access the various utilities built into the autoloader. You
can scroll between the various options using the Up or Down button.
1. Drive Alignment
The Drive Alignment menu is used to check the mechanical alignment be tween the drives
and the robotic arm. See Drive Alignment on page 36 for more information.
2. Spindle Alignment
The Spindle Alignment menu is used to check the mechanical alignment between the
spindles and the robotic arm. See Spindle Alignment on page 37 for more info rmation.
3. Disc Separator
Use this utility to tell the system the number of times for the robotic arm to shake the disc it
picked up from the input spindle in order to reduce the disc sticking issue. See Disc Static
and Sticky Media Is sues on page 2 for information about disc sticking issue and Disc
Separa tor on page 38 for information on using this menu.
4. Z form Maneuver
Use this utility to enable or disable the Z form maneuver. See Z form Maneuver on page
38 for information on using this menu.
5. Alignment Protection
Enabling Alignment Protection makes each drive tray quickly slide in and out after a disc
has been loaded into it. This ensures that the disc sits properly in the disc indentation of the
tray by shaking the disc into place. See Alignment Protection on page 38.
14. Manage Accounts page 39
Use this menu option to:
Create user accounts and passwords to prevent unauthorized use of the autoloader.
Edit existing user account information, including name and password.
Delete existing user account(s).
Enable/Disable this feature.
For additional information, refer to Introduction to Manage Accounts on page 10.
15. Shutdown page 41
Use this menu option to turn off your system. O nce you see the Ready to Power Off message, you
can safely turn off the machine using the power switch. Turning off your autoloader without
performing this function increas es the risk of damaging it.
16. AUTOCOPY (Hidden) page 30
Th e AUTOCOPY function simplifies the copy process by allowing you to stack blank media on a
spindle(s), place the master on top of the stack on the first spindle, and p ress the Enter button on
16.AUTOCOPY key in the main menu. It will load the content of the top disc of the 1
st
input spindle
(master disc) into the Reserved Partition of the Hard Drive and copy it to blank disc(s) below it and
other input spindle(s) if exists.
To activate this function, you need to activate it by going to 11. Setup -> 9.AUTOCOPY and turn
it on.

10
5. Introduction to Manage Accounts
This feature allows the administrator to:
Create user accounts and passwords to prevent unauthorized use of the autoloader.
Edit existing user account information, including name and password.
D elete existing user account(s).
Enable or disable Manage Accounts .
Manage Accounts is disabled by default. Prior to activating the Manage Accounts feature, the autoloader
recognizes all users as the Administra tor.
The pre - defined password for this function is 0000.
By adding additional users, each individual user has his/her own settings and only has access to the hard
drive partitions that the individual user loaded to the hard drive. No one else can access their hard drive
partitions other tha n the Administrator.
For example, if USER 1 logs - in and loads a master disc to hard drive Partition A, when USER 2 logs - in,
USER 2 will not have access to any parti tions loaded by USER 1; which includes partition A.
To take advantage of this feature, fo llow these instructions:
Change the Administrator password. Refer to Edit User Info on page 40 for additional information.
Create a User Name and Password for each authorized person on this autoloader. Refer to Create
User on page 40 for additional i nfor mation.
Enable the Manage Accounts feature by turning on the Password on Bootup setting. Refer to
Password on Bootup on page 41 for additional information.
Note: This autoloader comes with a standard license that allows you to create up to 3 2 users.
For instructions on how to use Manage accounts , see Manage Accounts on page 39.
6. Single Master and Multi Master Modes
There are two ways to make copies using the autoloader :
Single Master Mode:
This mode requires that a single master disc is loaded onto the hard drive prior to initiating the
duplication process. This mode is ideal if your job involves one or very few master disc(s).
Multi Master Mode (Batch Mode):
This mode does not require you to manually load your master. Simply p lace the master disc(s) on
top of the stack of blank discs needed for that particular job of the master disc. This mode is ideal if
you have numerous master discs and fewer copies for each master disc.
The Multi Master mode uses the Reserve partition to t emporarily store the content of the current
master disc. Once the task is complete and a new master disc has been detected, the reserve
partition's content (of previous master disc) will be replaced with the content of the new master disc.

11
You can tell immediately which mode you are in by looking at any of the Copy or Test menus:
The (SM) indicates Single Master Mode, and the (MM) indicates Multi Maste r Mode.
For example, if you need to make:
20 copies of job A
40 copies of job B
30 copies of job C
Under Multi Master Mode, you would need to follow steps below:
1. Make sure all of the spindles are empty.
2. Place 30 blank discs for job C on to the first input spindle.
3. Place the master disc for job C on top of those blank discs for job C.
4. Place 40 blank discs for job B on top of the master disc for job C.
5. Place the master disc for job B on top of those blank discs for job B.
6. Place 20 blank discs for j ob A on top of the master disc for job B.
7. Place the master disc for job A on top of those blank discs for Job A.
After you have completed these steps, the Input Spindle should be loaded in the
order shown in Figure 1 - 5:
When you start the copy operation, the robotic arm will pick up discs from the
Input Spindle and place them into the drives. If any of th e discs in the drives
contains data, (in this case, that would be the first disc, the Master Disc for job A)
the autoloader will load entire content of this disc(Master A) into the reserve
partition on the Hard Drive. The subsequent discs from the input bi n/spindle will
be loaded in the empty drives.
Once the loading process is completed, the autoloader will start the duplication
pro cess for the blank media in the remaining drives. Master disc A will be picked
up from the appropriate drive and dropped on to the Output Spindle and the
empty drive where the master disc was removed will be loaded with the next disc
from the input bin.
If a new master is detected before the previous job is finished, the autoloader will
complete the first job, unload the compl eted job, and fill the drive trays with blank
discs for the next job.
The robotic arm will continue to load media into the drives as the duplicated discs are placed in the Output
Spindles. Once a writer drive (any drive) detects an other Master disc, the same process is repeated for the
new Master disc.
Master A
20 Blank Job for
Mas ter A
Master B
40 Blank Job for
Master B
Master C
30 Blank Job for
Master C
Figure 1 -5
The Order of the Discs
ReflexAuto B.30
1. Copy (SM)
ReflexAuto B.30
1. Copy
(MM)

12
Counter:
Specify Counter
Specify Counter:
[0 ] OK?
Counter:
No Counter
7. Setting Counters and Assigning Names
Two frequently used tasks are setting counters and assigning names to parti tions. Directions for these tasks
are given here.
7.1 Setting Counters
The autoloader frequently gives you the option to set a counter so that the machine can keep track of the
number of copies made. Follow these steps when you see a Counter Selection Menu:
The Counter Selection Menu lets you set how many copies you want to
make for you r project. The Counter Selection feature tells the autoloader
to count the number of successful copies you have made and stop the job
when the desired number of copies has been reached.
You can select No Counter if you prefer to copy continuously with n o in terruption. (It will still count the
number of copies, but it will not notify you when to stop.) To select the No Counter , simply press the Enter
button when you see the screen above.
Or, you can select Specify Counter between 1 to 9999 by pressi ng the Up or Down button to go to the
Specify Counter menu:
Press the Enter button to select this option. You will see the next Specify
Counter menu.
To specify the number of copies for your project, you need to enter/input a
four - digit number.
If you need to specify a number that is less than four digits, fill the leading spaces with zeros (any leading
zeros will be skipped). Examples of four -digit numbers are 0234 (two hundred and thirty four), or 0010
(ten).
To enter the number, you need to use the Up or Down button to select the number for each digit and use
the Enter button or the ESC button to move the cursor position right or left. Once you've finished, move the
cursor to OK and press the Enter button. For example, if you want to speci fy a counter value of 21 (twenty
one). The 4 -digit value would be 0021. To input the de sired quantity, do the following:
Make sure the cursor is located at the first position (First blinking position):
Press the Down button repeatedly until 0 is displayed.
Press Enter button once to move the cursor to the next position.
Press the Down button repeatedly until 0 is displayed.
Press Enter button once to move the cursor to the next position.
Press the Down button repeatedly until 2 is displayed.
Press Enter button once to move the cursor to the next position.
Press the Down button repeatedly until 1 is displayed.
Now, 0021 is displayed, press Enter button once and the cursor moves to OK .
Specify Counter:
[0 ] OK?

13
Then, press the Enter button once to submit your counter value. The loader will now start loading disc from
the input spindles and place them into all drive trays.
7.2 Editing Names
When you create either a new user or a partition, you need to assign a name to it. The example shown here
shows how to name or rename a partition, but the process for naming or renaming the user name is
identi cal.
During the process of creating a new partition, you will see the Edit Partition Name menu:
To enter the name, use the Up or Down button to select the character and use the Enter or ESC button to
move the cursor position. Once you've finished, move the cursor to OK and press the Enter button.
The name for a partition can be up to eight character s long, and the characters can be any alpha (A...Z) or
numeric (0...9) value. For ex ample, if you want to name the partition for your master disc as FUN . Then
follow this example:
Press the Down button repeatedly until F is displayed.(You can also hold the Down button down,
and the autoloader will scroll through the alphabet.)
Press the Enter button once to move the cursor to the next posi tion.
Press the Down button repeatedly until U is displayed.
Press the Enter button once to move the curso r to the next posi tion.
Press the Down button repeatedly until N is displayed.
Press the Enter button once to move the cursor to the next posi tion.
Once you have the name FUN displayed and then, press the Enter button repeatedly until the
cursor i s moved to OK .
Then press the Enter button once to submit your name selection.
You will now see the following confirmation screen:
Press the Enter button to confirm.
Loading Partition?
[FUN ], OK?
Edit Partition Name
[ ] OK?

14
ReflexAuto B.30
1. Copy (SM)
ReflexAuto B.30
8. Mast
er Mode (MM)
Master Mode:
Multi Master
Master Mode:
Single Master
Chapter 2: Operation
This chapter shows each of th e menu options and how they are used.
1. Copy
The Copy menu option or the front panel Copy quick key have two different modes of operation:
Single Master Mode: This mode requires that a single master disc is loaded onto the hard drive
prior to initiating the duplication process. This mode is ideal if your job involves one or very few
master disc(s).
Multi Master Mode (Batch Mode): This mode does not require you to manually load your master.
Simply place the master disc(s) on top of the stack of blank discs needed for that particular job of
the master disc. This mode is ideal if you have numerous master discs and fewer copies for each
master disc.
These modes are described in detail in Single Master and Multi Master Modes on page 10. If you are
maki ng copies in Single Master Mode, contin ue on to the next section. If you are making copies in Multi
Master Mode, jump ahead to Making Copies in Multi Master Mode on page 16.
1.1 Making Copies in Single Master Mode
This process will copy your master disc on to several blank discs simulta neously. This mode requires that
your master disc is loaded into a partition on the Hard Drive. See Load Partition on page 25 for instructions
on how to do this.
Turn on your autoloader and wait until it has booted up. It should take several minutes for the autoloader to
go through its self adaptive test and auto - calibration pro cedures. You should see the following signifying
your autoloader is ready:
Make sure the Master Mode is set to Single Master mode (SM). If it is not,
use the Up or Down button to navi gate to the 8. Master Mode screen. If it is
already in Single Master mode (SM), please skip to the step that starts the
copy process.
Press the Enter button to enter the Master Mode Menu and you will see a
sc reen similar to one of the following:
Use the Up or Down button to se lect Single Master Mode. Press the Enter
button to submit your selection.

15
ReflexAuto B.30
1. Copy (SM)
Choose Partition
3 - >[FUN ]CD
Counter:
No Counter
Preparing...
Please Wait
Loader Processing
Drive 1 < -
Input Bin
Processing.. .
Please Wait
Go back to the 1. Copy Menu. Use the Up or Down button to navigate to the following screen:
Start the Copy Process. Insert your blank discs on to the Input Spindle(s)
and press the Enter button to enter the 1. Copy menu. You will see the
Choose Partition menu:
Use the Up or Down button to find the partition where your master disc is
stored. Press the Enter button to select that Partition. Next, you will see the
Counter Selection menu:
Follow the instructions shown in Setting Counters on page 12 to continue.
Once the counters have been set, press the Enter button to confirm. You
will see the Processing screen:
After a short interval, the robotic loader will pick the top disc from the input
spindle and place it into one of the drives. As this is happening, you will see
a screen similar to below:
This information screen shows what is happ ening. In this case, the loader
has taken a disc from the input spindle and is placing it into Drive 1.
The loader will continue to remove discs from the input spindle and place those into drives until either all of
the drives are full, or the count that you loaded into the counter is reached.
It takes a few seconds for the autoloader to recognize all the discs.
After two or three seconds of processing time, one of the following Copy Progress screens will appear.
Copying... H4012MB
0/21 12%
or:
Copying... H4012MB
0 12%
H indicates the source
of the job resides in the
Hard Drive.
4012MB indicates the
ca pacity of the master
disc.
12% indicates the
current progress of the
duplication.
0/21 indicates you have
a project size of 21 copies
and you have made 0
copies so far.
H indicates the source of
the job resides in the Hard
Drive.
4012MB indicates the
ca pacity of the master
disc.
12% indicates the
current progress of the
duplication.
0 indicates y ou have
made 0 copies so far.
Note: It is normal to see the progress indicator stay at 0% - 10% and 100% for approximately 30
seconds for CD duplication and up to one minute for DVD duplication. That is caused by the
initializing and finalizing stages.

16
Loader Processing
Drive 2 < -
Input Bin
Input Bin Empty(20)
Continue?
PASS 100 FAIL 0
Job Completed! Press OK to Finish
ReflexAuto B.30
1. Copy (MM)
ReflexAuto B.30
8. Master Mo
de (SM)
O nce the duplication run is completed, the loader will remove the finished
disc from the drive and place the successful copy on the Output Spindle and
if there are any bad/NG copy to the reject area.
The loader will then pick up another blank disc and lo ad it into the drive. This is then repeated for each disc.
The copying process will continue until you either run out of blank discs or
until the count that you loaded into the counter is reached.
If you run out of blank discs and the job is not com plete, the autoloader will give you an opportunity to fill the
spindle:
Important: When you add discs to the input spindle, be sure to remove your finished discs from the
Output Spindle.
At this point you can either put more discs on to the input spindl e and press
the Enter button to continue, or press the ESC button to terminate your
project.
Once the autoloader is through, you will see the following screen:
PASS 100" indicates that you made 100 successful copies.
FAIL 0" indicates that yo u have no failures for this job.
At the bottom of the screen, you will see the scrolling message: Job Complete! Press OK to Finish
1.2 Making Copies in Multi Master Mode
This mode does not require you to manually load your master. Simply place the maste r disc(s) on top of the
stack of blank discs needed for that particular job of the master disc. This mode is ideal if you have
numerous master discs and fewer copies for each master disc.
The Multi Master mode uses the Reserve partition to temporarily st ore the content of the current master disc.
Once the task is complete and a new master disc has been de tected, the reserve partition's content (of the
previous master disc) will be replaced with the content of the new master disc.
For more information on Multi Master Mode, see Single Master and Multi Master Modes on page 10.
Turn on your autoloader and wait until it has booted up. It should take several minutes for the autoloader to
go through its self adaptive test and auto - calibration pro cedures. You should see the following signifying
your autoloader is ready:
Make sure the Master Mode is set to Multi Master mode (MM). If it is not,
use the Up or Down button to navi gate to the 8. Master Mode screen. If it is
already in Multi Master mode (MM), please skip to the step that starts the
copy process.
Press the Enter button to enter the Master Mode Menu and you will see a
screen similar to one of the following:
Loader Processing
Drive 1 -
> Output Bin

17
Master Mode:
Single Master
Master Mode:
Multi Master
ReflexAuto B.30
1. Copy (MM)
ReflexAuto B.30
1. Copy (MM)
Preparing...
Please Wait
Loader Processing
Drive 1 < - In
put Bin
Processing...
Please Wait
Loading... RESERVED
36% 121MB Loaded
Loader Processing
Drive 1 -
> Output Bin
Use the Up or Down button to se lect Multi Master Mode. Press the Enter
button to submit your selection.
Use the Up or Down button to navigate back to the 1. Copy Menu.
Place your master discs and blank discs onto the Input Spindle as described in Single Master and Multi
Master Modes on page 10. In general, the order of the discs on the spindle will be, from top to bottom :
The master disc for the first job
The blank discs for the first job
The master disc for the second job
The blank discs for the second job
The master disc for the third job
The blank discs for the thi rd job
etc.
If your autoloader has more than one Input Spindle, then the job sequence can be spread across the
spindles, in sequence. CD duplication jobs and DVD du plication jobs can be intermixed. The autoloader will
automatically detect a job s master and blank disc format and copy them when they match.
You should still be at the 1. Copy Menu:
Press the Enter button to start the duplication job.
After a short interval, the robotic loader will pick the top disc (master disc)
from the Input S pindle and place it into one of the drives. As this is
happening, you will see a screen similar to below:
This information screen shows what is happening. In this case, the loader
has taken a disc from the Input Spindle and is placing it into Drive 1.
The loader will continue to remove discs from the Input Spindle and place those into drives until either all of
the drives are full or all Input Spindles are empty.
It takes a few seconds for the autoloader to recognize all of the discs in the
trays.
Once all of the discs are detected, the autoloader will detect the master disc
and read the contents of the master disc into the reserve partition.
Once the master disc has been loaded, the autoloader will remove the
master disc from the drive and pl ace it onto the Output Spindle.

18
Loader Processing
Drive 1 < -
Input Bin
Input Bin Empty (20)
Press OK to Continue
Master #1, Total 20
Pass 20, Fail 0
Master #2, Total 40
Pass 40, Fail 0
Master #3, T
otal 30
Pass 30, Fail 0
Access Log File
OK?
The loader will then pick up another blank disc and load it into the drive
where the last master disc was placed.
Once the loading process is completed, the duplication process will start. When the duplication process i s
through, the loader will remove the discs from the drives and place successful copies onto the Output
Spindles and place failed copies onto Rejected Area.
In Multi Master Mode, the robotic arm continues to load more media into the drives from Input Spindles
while the duplicated discs are placed in the Output Spindle. Once a new Master disc are been detected by
any of the drives, this process will repeat for the new Master disc.
When all of the jobs are complete, and the autoloader detects all Input Spin dles are empty, it presents you
with the Input Bin Empty message:
Press the Enter button to continue and you will see the Access Log File
screen:
Press the Enter but ton to view the log file or press the ESC button to return
to the 1.Copy menu. If y ou choose to see the log file, you will see a screen
similar to below:
Use the Up or Down buttons to look at the log file for the various jobs. Press
the ESC button to return to the 1.Copy menu
2. Test
Use the Test menu or Test quick key to simulate the copy process. With simulation, write once recordable
discs such as DVD - R, or CDR will be reusable. The purpose of simulation is to ensure error free duplication.
Note: Due to physical limitations of the DVD+R recordable format, if you try to simulate DVD+R
copying, you will encounter failure messages.
Warning : If you are using CD/DVD Rewritable discs as your media during the simulation, the
content on those discs will be permanently erased.
Operation in Test mode is identical to operation in Copy mode. See Copy on page 14 for instructions.

19
ReflexAuto B.30
1. Copy (MM)
ReflexAuto B.30
3. Compare
Choose Partition
3 - > [FUN ]CD
Counter:
No Counter
Preparing...
Please Wait
Loader Processing
Drive 1 < -
Input Bin
Processing...
Please Wait
3. Compare
Use the Compare function to perform a bit - by - bit comparison between the content of your master disc(s) in
the Hard Drive and the contents of all discs it copied. This ensures that all of your copies are identical to
original master disc(s).
Note: The bit - by - bit comparison will only apply on all DVDs and Data CDs. The readability check
will be applied for other formats like Audio CDs, CD+G, and Video CD discs due to their
lack of erro r correction mechanisms.
If you are at the 1. Copy Menu, do the following:
Use the Up or Down button to find the 3. Compare menu.
Press the Enter button on 3. Compare menu to enter the Choose Partition
Menu and you will see a screen similar to the following:
Use the Up or Down button to find the partition where your master disc is
stored. Press the Enter button to select that Partition. Next, you will see the
Counter Selection menu:
Follow the instructions shown in Setting Counters on page 12 to continue.
Once the counters have been set, press the Enter button to confirm. You
will see the Preparing screen.
After a short interval, the robotic loader will pick the top disc from the input
spindle and place it into one of the drives. As this is happening, you will see
a screen similar to below:
This information screen shows what is happening. In this case, the loader
has taken a disc from the input spindle and is placing it into Drive 1.
The loader will continue to remove discs from t he input spindle and place those into drives until either all of
the drives are full, or the count that you loaded into the counter is reached.
It takes a few seconds for the autoloader to recognize all the discs.

20
The system will then compare the discs in the trays to the content of the master disc residing in the Hard
Drive partition you specified. When the comparison job is complete, the autoloader will place the good discs
and failed discs into corresponding areas and you will see a PASS/FAIL re sult screen similar to this:
Counter Specified No Counter Specified
PASS 16 FAIL 0
Job Completed! Press OK to Finish
or:
Input Bin Empty (20)
Reset Hoppers?
PASS 16 indicates 16 discs have been
compared successfully.
FAIL 0 indicates none of t he discs
have failed.
Press the Enter button to finish
Input Bin Empty (20) indicates that the
system has run out of discs to compare.
If you have more discs to compare, you
can empty the Output Spindle; place the
discs to be compared in the Input Spindle
and Press the Enter button to continue.
If you have no more discs to compare,
press the ESC button to terminate the
operation.
4. Test+Copy
With the Test + Copy menu option, the autoloader simulates the copying process, and then makes copie s if
everything works correctly. If a failure is encountered on a disc during the simulation, it will not be copied
during the copying process while the discs that passed the simulation will move on to the copying process.
After the copying process, the au toloader will place the failure discs into the rejected area while the
successfully copied discs will be placed into the corresponding Output Spindle.
Operation in Test+Copy menu is identical to operation in Copy menu. See Copy on page 14 for
instructio ns.
5. Copy+Compare
The Copy + Compare menu option is used to make verified copies. After the copy process is done, the
autoloader automatically compares the copies to the master content residing in the hard drive to ensure that
they are identical. Wh en the operation is complete, the autoloader automatical ly places good discs on to the
Output Spindle and bad discs in the Reject Area.
Operation in Copy+Compare menu is identical to operation in Copy menu. See Copy on page 14 for
instructions.