Rimage Professional 5300N Instruction Manual

5300N™ Operator
2000516_A © 2007, Rimage Corporation 1
Replace the Bin Present Sensor or the Bin Full Sensor on a Rimage
5300N
Use this procedure to replace the bin present sensor or the bin full sensor on a Rimage 5300N™.
The procedures in this document should be performed only by personnel trained and authorized by Rimage. The instructions and
content are written for mechanical and electrical service work assuming the technician has such training and authorization. The
product warranty may become void if equipment or parts are tampered with, misused, neglected, or modified in any respect without
the written consent of Rimage or by technicians who are not authorized or certified by Rimage.
Before you begin
1. Stop or pause all jobs.
2. Power off the embedded control center.
3. Power off the 5300N.
4. Disconnect the power cord.
#Required tools:
•¼” nut driver
•Torx T8 screwdriver
•Torx T10 screwdriver
Access the sensors
1. Open the front door.
2. Remove the nuts (Qty. 2) securing the sensor bracket.
3. Remove the sensor bracket and sensors.
4. Disconnect the sensor cables (Qty. 2) from the sensors.
nCaution! Some cables in this system are latched.
Equipment damage may occur if cables are not
disconnected appropriately.
Sensor Bracket
and Sensors
Sensor Cables

Replace the Bin Present Sensor or the Bin Full Sensor on a Rimage 5300N
2 © 2007, Rimage Corporation 2000516_A
Replace the bin present sensor
1. Remove the Torx T10 screw (Qty. 1) securing the
bin present sensor to the bracket.
2. Remove the bin present sensor.
3. Position the replacement bin present sensor on the
bracket.
4. From the top of the sensor, insert the Torx T10
screw (Qty. 1) to secure the sensor to the bracket.
Bin Present Sensor
Replace the bin full sensor
1. Remove the Torx T8 screw (Qty. 1) securing the bin full
sensor to the bracket.
2. Remove the bin full sensor.
3. Position the replacement bin full sensor on the bracket.
Notes:
Bin Full Sensor
•The sensor is on the opposite side of the bracket as
the bin present sensor.
•The sensor is positioned so that the screw is
inserted into the hole with the raised edge.
4. Insert the Torx T8 screw (Qty. 1) to secure the sensor to the
bracket.
Raised Edge
and Screw
Reassemble the 5300N
1. Connect the cables (Qty. 2) to the sensors.
2. Position the sensor bracket over the studs on the frame.
3. Secure the sensor bracket with the nuts (Qty. 2).
4. Connect the power cord.
5. Run
diagnostic test 6 – Sensors diagnostic test. More information on diagnostic tests is available in your
5300N user guide.

5300N
Learn more
Rimage Corporation reserves the right to make improvements to the equipment and software described in this document at any time
without any prior notice. Rimage Corporation reserves the right to revise this publication and to make changes from time to time in
the content hereof without obligation of Rimage Corporation to notify any person or organization of such revisions or changes.
Support information
US, Asia/Pacific, Mexico/Latin America Europe
Rimage Corporation
7725 Washington Avenue South
Minneapolis, MN 55439
USA
Attn: Rimage Services
Rimage Europe GmbH
Albert-Einstein-Str. 26
63128 Dietzenbach Germany
Contact Rimage Services:
www.rimage.com/support.html
Email: http://www.rimage.com/support_form.cfm
Tel:
North America: 800-553-8312
Asia/Pacific, Mexico/ Latin America: 952-946-0004
Fax: [phone]
Contact Rimage Services Europe:
www.rimage.com/support.html
Email: [email protected]
Tel: [phone]
Fax: [phone]
When you contact Rimage Services, please provide:
•Unit serial number and software version.
•Functional and technical description of the problem.
•Exact error message received.
Safety Information
Rimage 5300N™
This information and the indications on the product allow proper and safe operation. The indication marks below help protect you
and other persons from injury, and equipment from damage.
-Important! Any equipment that has certain components using AC line voltage, or in some cases low DC voltages, such as
power switches, power supplies, fuses, fans, non-stepper motors, must be replaced with Rimage–approved components to
maintain the safety approval issued by UL.
nwarning is used to indicate situations that
nn: Indicates that failure to observe this guideline could result in loss or damage to the equipment, product, software, or
, please read these precautions and familiarize yourself with their meaning before using the equipment.
n
r beam used by the DVD-R recorder is a Class 2 laser and can be harmful to the eyes. Do not attempt to open the
nCa
tors,
eplaced with Rimage-approved components to maintain the safety approval issued by UL.
rmation or to order a new power cord, contact Rimage Customer
Service.
This product is designed for an office environment.
Warning! According to ANSI (American National Standards Institute) standards, a
could result in bodily injury to personnel operating or maintaining the equipment.
Cautio
data.
Safety precautions
To ensure safety
Warning!
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiant exposure.
The lase
recorder. An authorized technician should perform all service procedures.
ution:
All equipment with AC line voltage, or low DC voltages, such as switches, power supplies, fuses, fans, non-stepper mo
must be r
Use only the supplied AC power cord. For more info
2000516_A © 2007, Rimage Corporation 3