Davey 5190HRS User manual

ASSEMBLY INSTRUCTIONS
Convert this:
To this:
Note: Battery not included with 5190HRS, 5290HRS or 32946 and must be purchased
separately. For battery details consult Installation and Operating Manuals included
with 5190HRS or 5290HRS.
Remote/Auto Control
Firefighter Mobile Kit
to suit 5190HRS & 5290HRS
P/N: 32946

ITEM No. DESCRIPTION QTY.
1Wheel 2
2Axle 1
3Washer 4
4Spacer – Plastic 2
5Split Pin 2
6Handle 2
7Brace Bracket 1
8Bolt 5/16 UNF x 1.5 8
9Nut – Conelock – 5-16 BSW 8
10 Tube Plug 25mm 4
11 Handle Bracket 4
12 Dome Bolt Cap 2
13 Washer – 5/16 x 5/8 8
Check to ensure all parts are included as per below:
1
23
4
5
10
6
11
13
9
12
7
8

STEP ONE: Wheel Assembly
1) Slideitem2(axle)throughthetwoholesintheplatesafxedtothebottomsideofthe
5290HRS frame (engine end).
2) Slide one each item 4 (spacer) over each end of the item 2 (axle)
3) Slide one each item 3 (washer) over each end of the item 2 (axle)
4) Slide one each item 1 (rubber wheel) over each end of the item 2 (axle)
5) Slide one each item 3 (washer) over each end of the item 2 (axle)
6) Insert one each item 5 (split pin) into the hole at each end of the item 2 (axle)
7) Separate the split pin to ensure retention of the wheels – see below
NOTE: Therubberfeetormountsenclosedwiththe5190HRSor5290HRSmustbettedto
the frame to ensure wheels will not engage with the ground when in stationary position.

STEP TWO: Handle Assembly
Note:Thehandleassemblyisdesignedtobelaidatacrossthetopoftheframewhennot
required to move the 5290HRS system.
1) Insert one each item 11 (tube plug) into each end of the item 6 (handle).
2) Loosely mount the item 7 (brace) to the two item 6 (handle) using item 9 (bolt), item 13
(washer 5/16 x 5/8) and item 10 (conelock nut) on each end – do not fully tighten yet.
Set aside handle and brace assembly for now.
3) Loosely mount two each item 8 (handle bracket) to the two top corners of the frame –
engine end using item 9 (bolt) and item 10 (conelock nut) on each end – do not fully
tighten yet.
4) Take the handle and brace assembly and mount it to the handle brackets using item 9
(bolt) and item 10 (conelock nut) on each side - do not fully tighten yet.
5) Tighten the various item 9 (bolt) and item 10 (conelock nut) starting with the four holding
the item 8 (handle bracket) to the frame, then the two holding the item 7 (brace) to the
two item 6 (handle).
6) Finally tighten the two bolts holding the handle and brace assembly to the handle
brackets, ensuring it is still free to move from the vertical (transport position) to the
horizontal (storage position).

STEP THREE: Dome Nut Protector
Toprotectthehandlewhenlaidatthetwoblackdomenutprotectors(items12)shouldbe
placed over the frame centre brace mounting bolt heads as shown below:
12

AUSTRALIA
Customer Service Centre
6 Lakeview Drive,
Scoresby, Australia 3179
Ph: 1300 232 839
Fax: [phone]
Email: [email protected]
Website: davey.com.au
Davey Water Products Pty Ltd
Member of the GUD Group
ABN 18 066 327 517
NEW ZEALAND
Customer Service Centre
7 Rockridge Avenue,
Penrose, Auckland 1061
Ph: 0800 654 333
Fax: [phone]
Email: [email protected]
Website: daveynz.co.nz
® Davey is a registered trademark of Davey Water Products Pty Ltd. © Davey Water Products Pty Ltd 2016. P/N 15697