Dawlance DWT 1166 X ADS+ User manual

Fully Automatic Washing Machine
User Manual
DWT 1166 X ADS+

Contents
Before using
Parts name................................................................................................. 1
Cautions..................................................................................................... 2
Installation and adjustment........................................................................ 4
How to use drainpipe................................................................................. 5
Water inlet installation................................................................................ 6
Operation
Preparation before operation..................................................................... 8
Load laundry.......................................................................................... 9
Use of detergent........................................................................................ 9
Control panel instructions.........................................................................10
Operation steps........................................................................................ 12
Maintenance............................................................................................ 13
Troubleshooting....................................................................................... 14
Other functions.........................................................................................16
DWT 1166 X ADS+
220V~50Hz
65 Litre
560x560x965 (mm)
Refer to Specication Label
0.03 MPa- 0.3MPa
Model
Rated voltage and frequency
Water level/water volume (about)
Product dimension (WxDxH)
Rated input power-rated voltage
Inlet Pressure
Specications

1 2
CautionsBefore using
Do not install the washing machine in the bathroom or any
other damp places. Do not wash the machine with water and do not
put wet clothes on the control panel lm.
Do not use water hotter than 50 C.
If the machine is placed on a carpeted oor, please adjust
the feet in order to allow air to circulate freely.
Do not wash raincoat, bike cover, feather dress and such
waterproof laundry as it will cause unusual vibrations during
spinning.
Do not share the same socket with other electric appliances.
Do not use a damaged plug or a loose socket.
Please insert the plug into the power socket with voltage rating
220V A/C.
Always unplug the appliance and turn off the water when
the power is cut, the machine is moving, getting cleaned,
or it isnot inuse. Do not insert or pull off the plug with wet hands.
Do not bend, stretch, twist, strap, change, press or nip the electric cable. If the electric cable or plug is damaged or the socket
becomes loose, they must be repaired or changed by our appointed repair stations or the professionals of our post-sale service
department to avoid danger. The pin of the plug must remain clean. Please clean it carefully with dry cloth, if it is dirty.
Ventilation holes
at the bottom
Soft item
Before using
Parts name
Before using
Symbol definition
Warning symbols
Pay special attention to the warning symbols. There may be
serious risks to personal body safety or damages to the washing
machine, if not followed.
Please stop doing the contents with this symbol, otherwise
it will damage the appliance or injure your body.
Forbidden symbols
Accessories
The end connecting to
the appliance
Connector for
water inlet hose
and tap
The end connecting to
water inlet hose connector
Bottom cover
(1pc)
Water inlet hose (1 pc)
Water inlet hose connector (1 pc)Drainpipe (1pc)
Drainpipe clip (1pc)
Top lid
Top frame
Lint filter
Pulsator
Body
Base
Power cord
Fixing foot (3pcs)
Back cover
Adjustable foot
Foot wheel (2pcs)
Feed valve
Water box lid
Detergent
box
Softener
feed in
Inner tub
Control panel
(glass lid front)
Drainpipe connector

3 4
Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp materials can cause extensive damage and
must not be placed in the machine.
Before washing, please ensure the tap is open and the inlet hose is installed properly.
It is suggested to use low foam washing powder.
Do not put your hands inside while the machine is working.
It is dangerous even if the speed is very slow.
Take special care of the children and forbid
them to climb onto the washing machine.
It is dangerous to alter the specications or
attempt to modify this product in any way.
Do not overload the appliance or put any hot
items (such as the kettle with hot water) on the
washing machine.
Garments, which have been in contact with
volatile petroleum products, should not be
washed in the machine.
Keep the appliance away from direct
sunlight and heat sources like the heater.
Benzene
Petroleum
Thinner
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities or lack of
experience and knowledge. Unless, they have been given supervision
or instruction concerning the use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with
the appliance.
CautionsBefore using
Before using
Please install and adjust the machine according to the requirements of the manual.
It is very important for your safety and correct operation.
Unpacking
Unpack the carton and take out the bottom panel.
Open the top lid of the washing machine and take out all of the accessories.
Remove all wrappers, including the polystyrene base.
You are advised to keep all of the packaging for reuse, in case the machine is to be
transported again.
Installation and adjustment
Before using
Installing the bottom cover
Let the back of the washing machine incline forward. Then
make sure the bottom side cover, with the description sticker,
is to the back of the machine. Then inserted into the bottom
of the machine, as directed by the direction of the arrows.
Remove the two fixing clamps using a pair of scissors.
Insert them accordingly, into the holes indicated by the
blacklines. Gently pull the fixing clamps, make sure
they do not come out. Ensure that the bottom cover is
fixed on the base.
Fixing clamp
Scissors
Bottom cover
The base
Positioning
The distance between the washing machine and the wall should be more than 50mm, and the
maximum allowed angle of the shank base of the machine is 1 . The slanting or rough ground may
cause instability or the operation to stop. Please adjust it with the following methods:
Make it horizontal
Use a tied thread with plumb to check
if it is horizontal.
Adjust the adjustable foot
1. Lift up the adjustable foot gently, loose the adjustable nut
and twist the adjustable foot.
2. Fasten the nut after adjustment.
LoosenAdjustable
foot
nut
HighLow
Adjustable
Fasten
1o

5 6
Water inlet installation
>10mm
Lock lever
Inlet hose
Inlet hose connector
Slider
Screwdriver
Bolt
Bushing
Before twisting, about 4mm
After twisting, less than 2mm
Nut
Illustration 1 Illustration 2 Illustration 3
Illustration 6
Illustration 5
Illustration 4
Tap selection
Suitable tapUnsuitable tap
The front end should be longer than 10mm.
The tap exit end face should be at and smooth, if not, le it to avoid leakage.
Connect the inlet hose connector with the tap
1. Press the lower end of the lock lever and push down the slider. Take off the inlet hose
connector from the inlet hose, see illustration 1.
2. Loosen the four bolts on the inlet hose connector till thetap can be accessed. Then
set the inlet hose connector to the tap, see illustration 2. (If the tap caliber is too large and
could not t the inlet hose end, unscrew the four bolts and take out the bushing. The tap exit
end must be at, otherwise it will leak, see illustration 3).
3. Fasten the four bolts in the inlet hose connector evenly, see illustration 4.
4. Twist the fastening nut as the illustration, see illustration 5.
Remark: Before twisting the nut, the threading should be about 4mm above the upper surface of the nut. After
twisting, the threading becomes less than 2mm above the upper surface of the nut, see illustration 6.
Before using
How to use drainpipe
Water drainage
The drain hose should drain smoothly.
1. The height of the drain hose should be less
than 10cm, otherwise the drainage will not be
smooth and would need a long time to drain. The machine
may stop, while working.
2. Do not step on or press the drain hose.
4. Purchase a proper hose, if you need an additional one.
Its diameter should not be less than 30mm and the length
should not exceed 1.5m.
A B
3. Cut the drain hose, if it is too long. Cut the front end of the
hose slantingly to make drainage smoothly.
How to change the direction of the drainpipe
1. Take off the drainpipe and its clip from the connector.
Put a soft mat on the oor & make the washing machine
front side down. Now, gently
demount the screws on the
back cover with a screwdriver
and take it out. Demount
one screw from the drainpipe connector (on the right side of
the washing machine) & loosen it.
3. With proper force, take down the drainpipe gate stopper
on the left side of the washing machine. The drainpipe gate
stopper is xed on the washing machine base with two
clips. Please see the xing type from the place of
back cover opening.
2. Extrude the drainpipe with proper force
and take out the drainpipe hoop (on right of the
washing machine). Loosen the inner
drainpipe.
4. Pull the inner drainpipe to another side.
Please do not make any distortion in the
inner pipe; as per the foregoing description,
x inner drainpipe with a drainpipe hoop.
With one screw, x drainpipe connector
and install the drainpipe gate stopper to
another side. Make the washing machine
stand gently and x the back cover with
a screw. Now, install the drainpipe and
the drainpipe clip into the drainpipe connector.
Install drainpipe
Set drainpipe clip into the drainpipe to above 2-3cm (from the drainpipe end without pothook).
Now, install the drainpipe into the right drainpipe connector and x the drainpipe
and the drainpipe connector with the clip. After that, put the drainpipe clip on the cabinet.
Drainpipe hoop
Drainpipe connector
Drainpipe
Drainpipe clip
(Section sketch map for washing machine right side)
Section sketch map inside washing machine
Drainpipe gate stopper
Section sketch map for washing machine left side
Before using
,
If the additional drain hose is too long,
cut some at A or B point.

7 8
Water inlet installation
Before using
Connect the inlet hose connector with the inlet hose
Check the connection between the inlet hose
connector and the tap
Inlet valve connector
Inlet hose nut
Water absorption cushion
Lock lever
Inlet hose connector
Slider
1. Push down the slider and insert the inlet hose into the connector.
2. Hang the lock lever to the inlet hose connector andrelease
the slider till a click sound is heard.
1. Swing the inlet hose gently to conrm if it is fastened.
2. After installation, open the tap and check if it leaks.
3. Do not bend the inlet hose with overstrain.
4. Before each usage, check the connection between
the inlet hose connector and the tap. Also, make sure that
the inlet hose is installed properly. Conrm that they are rmly
tted to prevent dropping from improper installation position.
Slider
Lock lever
Connect the inlet hose with the washing machine
1. Do not take off the water absorption cushion. Please
check if the cushion is dropped or damaged before
each use. If it is, contact the seller immediately.
2. Put the inlet hose nut on the inlet valve connector.
3. Fasten the inlet hose nut and swing it gently tomake
sure if it is suitable.
1. Close the tap.
2. Press the locking lever, push down the slider, and pull off the
inlet hose. If the machine is used frequently, the connector
of the inlet hose can be kept on the tap to prevent damage to
the xing screw.
Dismantle the inlet hose
Cautions:When installing the washing machine, please use the new hose along with the washing
machine. Old hose cannot be reused.
Preparation before
operationOperation
Preparation before washing
1. Connect the inlet hose and open the tap.
2. This appliance must be earthed. Conrm
the socket is earthed reliably and insert the
power plug. The earth terminal should not
link to the gas pipeline, tap pipeline etc.
3. Put down the drainpipe.
Before washing the laundry, please pay attention to the following:
Make sure to be aware
if there are any special
requirements for the
laundry.
Before washing, empty
all the pockets of small
objects, which may
have been left inside
(coins, keys, screws etc.)
as these could damage
the drain pump.
Knot the long band,
fasten the buttons
and close the zippers.
Do not overload the
machine. Load the
laundry loosely
alternating large
items with small ones.
Sort the laundry
according to the type
of fabric, color-fastness
and how dirty it is. Put
thin laundry, woolens
and such prone to wear
and tear laundry into a
washing bag.
A. Make sure the laundry is washable.
B. It is essential to wash new colored items separately when washing forthe rst time. White items
should not be washed with colored items.
C. Please immerge the non-absorbable laundry by hand.
D. Some stains such as fruit, wine, grass, rust etc. are difcult to remove and should be treated
before washing with specic products, which can be found in most household shops. In some
cases, it may help soak the stain before washing with a special pre-soak product or biological
detergent.
E. Overturn the nap fabric and long oss laundry before putting them into the machine.
F. Do not put the laundry polluted by chemicals into the machine directly.
G. Very small items (handkerchiefs, ribbons, socks etc.) should be washed in a washing bag or a pillow case.
Warning: The temperature of the water should be less than 50

10
Mode and meaning of the indicator light
The indicator light is always on, indicating that it is not selected.
The indicator is flashing, indicating that it has been selected.
The indicator lights flash quickly to indicate that something is wrong.
Water level
In the process of washing (including rinsing), if you want to fill the water, you can press the "start/
stop" key, then press the parameter key to select "water level", then press the "set" key to select
higher water level, and then press the "start/stop" key to run, the washing machine will
automatically feed water to the set water level, and then continue to run.
If the changed water level is lower than the current water level in the barrel, the machine will
continue running after a pause, and the changed water level will be reflected in the next time the
water comes in.
Automatic filling of water is the process of "soaking", "washing" and "rinsing", if the washing
machine detects that the water level drops below the water level by set, the washing machine will
be suspended, and automatically rehydrate to set water level and continue operation.
After selecting the program, water level and other parameters, press this key to start operation.
Press this button during operation to suspend operation, and press this button again to continue
running until the remaining time is completed.
At the initial state of startup, the detergent lamp is shiny, indicating that the function of
automatically putting detergent is selected. Press the function key this time to select detergent,
softener, and barrel self-cleaning. Followed by no choice - softener - detergent + softener - tub
clean - detergent, the selected will shiny.
At the initial state of startup, press the function button for more than 2 seconds to switch to the
selection of water recycle and air drying, which in turn is water recycle - air drying - no selection.
Press the function button for more than 2 seconds again to switch to the above detergent,
softener and barrel self-cleaning options.
After washing machine starts, press function key to select child lock, press again to cancel
child lock.
Initial state
Switch on, press the "power switch" button, and the machine enters the initial state:
a. If there is no water in the inner bucket, the machine will in "fuzzy" working state, the detergent
lamp is shiny. Wash (default 15 minutes), rinse (default 2 times), spin (default 7 minutes) will
twinkle; nixie tube display "- - "; program display "normal". If press "start/pause" directly
(press "program" chose "heavy" also have fuzzy function), the machine will fuzzy sensing, sense
the amount of clothing automatically. Set water level and finish the whole process of washing.
b. If there is water in the inner bucket, the machine will not in "fuzzy" working state, detergent lamp
is shiny; wash (default 15 minutes), rinse (default 2 times), spin (default 7 minutes) will twinkle;
water level default 7 levels; program display "normal"; nixie tube display water level "7", after 5
seconds display the time of program.
Control panel instructionOperation
9
Load laundry Operation
The capacity of washing and spinning of the machine refers
to the largest weight of the standard laundry under dry
conditions. Washing quantity shall be lower than the rated
capacity. The maximum capacity of this machine is 8.0 kg.
Different thickness, size and type of the laundry will
influence the actual washing capacity. It is suitable that
the laundry can be turned around normally during washing.
Do not select high water level when the laundry are less than
1.5 kg to avoid water splashing.
There is no laundry powder input. If the user USES the washing powder. Please follow the
instructions and press the "auto drop" button, once after starting up the machine to cancel
the auto drop function.
1.Dissolves directly in the washing machine.
Inject a little water.
Put in the washing powder and run for
about 30 seconds to fully dissolve it.
Put in the washes and choose the
appropriate water level.
2.The instant solution method of washing powder
Prepare the container and approximately 30oC
of warm water.
Whisk and add the washing powder to dissolve it.
Refer to the instructions of washing powder for the amount of washing powder.
Low foam detergent is recommended.
Please refer to the instructions of washing powder for the dosage of concentrated
washing powder.
Notice: Washing powder is easier to pollute than detergent, so use it in moderation.
If the washing powder is of poor quality or has been ineffective for a long time, it
may become lumpy. Please pay attention to cleaning the detergent box in time.
How to use liquid detergent
Can be directly put into wash bucket. After starting up, press the "auto drop" button once
to cancel the auto drop function.
Auto drop: Open the lid of the water box and pour the detergent into the detergent box
(the box can hold about 1.5L) (as shown in the figure below)
The washing machine will automatically add detergent when the machine is turned on.
After putting the clothes and setting the water level, users do not need to add detergent.
The washing machine will automatically add detergent according to the water level set by
users. When the detergent in the detergent box is insufficient, the washing machine will
alarm and prompts the user to add.
How to use a softener
Please refer to the product manual for injection amount of softener. Manually add the
softener to the washer bucket during the last "rinsing".
If the softener is put into the softener box through the washer port, please be careful not
to exceed the rib in the softener box. The washer will automatically add the softener to the
washer bucket during the last rinse.
Use concentrated softener diluted with 3 times water.
How to use bleach
After the water is injected to the specified water level, dilute the bleach in the container
and slowly pour into the wash bucket.
Bleach should not contact the detergent directly. Bleach should be avoided in coloured
or patterned clothing.
Powder - type bleach should be used after dissolving.
Use method and the amount of bleach should strictly as per the instructions.
Indicating rib
Water box lid
Detergent
box
Softener
feed in
Water Recycle Air Dry Child Lock
Detergent
Softener Tub Clean
Normal Eco+
Fast Delicates
FUNCTION

12
Operation steps Operation
Operation steps
1. Put through the power, press POWER SWITCH button, the machine enters into initial condition.
a. If there is no water in the inner bucket, the machine will be in "fuzzy" working state, the detergent
lamp is shiny. Wash (default 15 minutes), rinse (default 2 times), spin (default 7 minutes) will
twinkle; nixie tube display "--"; program display "normal". If you press "start/pause"- directly
(press "program"choose heavy also have "fuzzy"function), the machine in fuzzy will, sense
the amount of clothing automatically. Set water level and finish the whole process of washing.
b. If there is water in the inner bucket, the machine will not be in "fuzzy" working state, detergent lamp
is shiny; wash (default 15 minutes), rinse (default 2 times), spin (default 7 minutes) will twinkle;
water level default 7 levels; program display normal; nixie tube display water level 7, after 5
seconds display the time of program.
2. At the initial state of startup, press the "program"key to choose different programs.
3. At the initial state of startup, press "parameter"key to choose wash or rinse or spin, then
press set key again can choose different washing time or rinsing time or spinning time.
4. According to the amount of clothing, press "parameter"key to choose water level, then press
"set"key to choose suitable water level.
5. At the initial state of startup, press "parameter"to select "soak", and then press "set"to select
different soaking time.
6. At the initial state of startup, to select the reservation function, press "parameter"to select
"preset", and then press "set" to select different appointment times.
7. In the initial state, the detergent lamp is shiny, washing machine automatically puts detergent by
default. You can also press the "function"key once to cancel this function, and users put the
detergent by themselves. When this function is selected, the laundry machine automatically adds
detergent according to the water level was set. When the detergent in the detergent box is not
enough, the laundry opportunity alarm prompts the user to add.
8. In the initial state, press the "function"key to select "detergent (automatic delivery)", "softener",
and "tub clean" circulation; hold "function" key more than 2 seconds, can change to "water recycle"
"detergent", "softener"and "tub clean".
9. Close the top lid and press the start/stop button to start running. During the operation, press
the "function"key once to start the child lock function, and press the function key again to
relieve the child lock. If the top lid is opened after starting the child lock function, the washing
machine will stop running and alarm.
10. When the washing process is over, the buzzer will alarm and the washing machine can be
turned off automatically.
and "air dry"selection. Press "function"button for more than 2 seconds again to change to
11
Control panel instructionOperation
Before washing, the digital timer shows preset time, unit is HOUR.
If select AIR DRY, the digital timer displays air dry time, unit is MIN.
Displays 1-10 levels when selecting water level.
When washing, the digital timer shows the rest time of washing, unit is MIN.
When trouble encountered, the digital time shows trouble code.
At the beginning of start, if with FUZZY logic, The digital timer shows "--".
Used to control washing machine in
working state or standby state.
In the initial state of the startup, the program is set to "normal", the normal lamp will shining.
It can be successively carried out "normal", "spin only", "eco+", "fast", "delicates", "child",
"heavy" and "shirts". 8 programs can be choose, selected program lights flashing.
At the initial state of startup, the light of wash, rinse and spin will shiny and are selected. At this point,
press the parameter key to select, which in turn is wash - rinse - spin - water level - soak-preset -
wash + rinse and spin (initial state).
In the initial state of startup, the setting button is not available. When selecting wash--rinse--spin--
water level--soak--preset by pressing the parameter key, the corresponding washing time, rinsing
times, spinning time, water level, soak time and appointment time can be selected by pressing the
setting key.
The washing time option is 15 - 20 - 9 - 12 - 0 cycle. When 0 is selected, the washing process is cancelled;
Rinse cycle option is 2 - 3 - 4 - 1 - 0. Select 0 to cancel the rinse process; The spin time is selected as 7 - 9 -
2 - 3 - 5 - 0 cycle. When 0 is selected, the spin process is cancelled; The water level option is 1 to 10; The
soaking time option is 0 - 15 - 25 - 35 cycle. Select 0 to cancel the soaking process; The appointment time
option is 0 - 2 to 24 loops. When you select 0, cancel the appointment;
The washing time, rinsing time and spinning time should not select 0 at the same time; The unit of
washing time, spinning time and soaking time is minutes; The units of rinsing times: times ; The unit of
appointment time: hours. The corresponding, "time and minutes" will be shiny when set.
Washing time, rinsing times, and spinning time cannot be set when the program selects normal or
fast or soft or shirt. Parameters cannot be set when the program selects spin only.
Spin Only
Heavy
Child
Shirts
Wash
Water Level
Rinse
Soak
Spin
Delay Start
PROGRAM SELECT
*Disclaimer
Saves upto 36% of Detergent on Eco+ program.
Stores upto 15 cycles of detergent while using machine on water level number 4.

13 14
The machine stops automatically, and music
the buzzer will remind you to take out the
laundry or start again.
Once you have nished using the machine,
you are advised to unplug it and turn off the
water tap to avoid unexpected leak or re.
After the end of the programme
Clean the exterior cabinet of the appliance with a
soft cloth. Do not use cleanser or volatile chemical
materials to clean the machine. These will damage
the plastic parts and the surface.
External cleaning
Clean inlet gate
It is possible that the inlet lter net can be blocked
by dust. Please clean it according to the following
steps:
1. Close the tap and turn on the power switch.
2. Start the washing machine for 5 seconds (let
the water in the inlet hose ows to the tub), and
cut off the power supply.
3. Pull off the inlet hose, remove and clean the inlet
valve and the inlet net, and install again.
Magic lter cleaning
1. Pull out the magic lter.
2. Open the box and clean it.
3. Close it and reinstall it.
4. Check if the lint block part is in good condition.
Press this part and pull out to take
out the magic lter
Lint block part (black rubber)
MaintenanceOperation
1. Once you have used the machine, you are advised to turn off the water tap. (If necessary, pull out
the inlet hose).
2. Do not keep the water in the tub for a long time. When washing is nished, drain it right away.
3. Once you have nished using the machine, you are advised to unplug it.
4. Put the electric cable and the drain hose in order.
5. Wipe the water on the surface and in the tub with a soft cloth and keep the top lid open for a while. It
helps prevent mould and stagnant smells from forming inside the appliance.
Maintenance methods
If the water in the inner tub has possibility to freeze, please do as below:
1. In winter, if the remaining water freezes, it can cause the washing machine trouble.
Please take off the water inlet hose and drain out the water from the hose and inner tub.
2. If the water freezes, please don't operate the washing machine. Put 40oC hot water
in the tub. The hot water should submerge the pulsator. After a few minutes, rotate
the pulsator by hand gently. Now, you can operate the washing machine.
Troubleshooting
It does not drain
It does not inlet
Spin stops and begins to inlet
during spin program
Press the program button to
select SPIN, but it does not spin
The spin is intermittent when
spin starts
First time to use, some water ows
from the drainpipe
No water supply.
Tap is not open.
Inlet hose is blocked.
Laundry is too much or too little or the
machine is not place stably.
Before contacting the technicians, please make the following checks:
Control panel has no display
Plug is not inserted tightly.
No electricity in the socket.
Power switch is not turned on.
Power supply is cut off.
Inlet hose leaks
Inlet hose connector (connecting with the tap) is not xed tightly.
Inlet hose and washing machine connector is loose.
Drainpipe is not put down.
Drainpipe is bended or blocked.
The remaining water when the factory made test.
Do not close the top lid when drain is nished.
Open up the top lid when start drain.
Balance the laundry to reach to the best spin effect.
PhenomenaPossible reason
Settlement

Settlement
Insert the plug tightly.
Check the socket or change to another socket
Press the power switch.
Check the power supply.
Install the inlet hose again.
Tighten the connector of the machine.
Restart when water supply is resumed.
Open the tap.
Clean the lter according to before “clean inlet gate”.
The machine is adjusting automatically.
Close the top lid.
Normal
Normal
Notes: If there is still a fault after the above checks, please pull out the plug and
contact the seller right away. It is dangerous to repair this product by yourself.
Put down the drainpipe.
Straighten or clean the drainpipe.
Settlement
15 16
Other functions
1. Give an alarm
E1
E3
E2
F1
E4
E0
DisplayExplanation Settlement
The top lid is opened
when preset is started. Close the top lid and clear up the alarm.
After draining for 7 minutes,
it still does not reach to
water level.
Open top lid, according to before
troubleshooting and settlement to
settle it, then close the top lid and
clear up the alarm.
The top lid is open while
spinning.
Close the top lid and clear up the alarm.
Spin does not balance.
Open the top lid, make the laundry
place equally, then close it and clear
up the alarm.
After 40 minutes, the inlet
still does not reach the
settling water level.
Open top lid, according to before
troubleshooting and settlement to
settle it. Then close the top lid and
clear up the alarm.
Water level sensor is wrong.
Cut the power supply and call the
technicians.
E5
Child-lock light is
ashing synchronously
The top lid is opened
after setting child-lock.
Close the top lid and clear up the
alarm.
Detergent lamp is
twinkling quickly
Detergent lamp is
twinkling quickly
At the initial state of the
machine, the liquid in the
detergent box is
automatically put into default
when it is not enough.
Add manually, release alarm.
Eb
Add manually, release alarm, press
" " to resume running.start/pause
Automatic adding by default,
when the liquid in the
detergent box is not enough,
need add manually.
vibration testing system will supervise the running. Once the vibration is beyond a certain
3. Power supply is cut off automatically
machine to vibrant violently. This machine has an imbalance adjustment function and the
During spinning, if the laundry is not placed equally in the tub, it would cause the
2. Imbalance adjustment
level, the adjustment system will start to adjust the imbalance automatically.
1) Press the power supply button. If it does not start the program in 10 minutes,
the power supply will be cut off automatically.
2) After the washing is nished, the buzzer will remind, and the power supply
will be cut off automatically.

17
Other functions
5. Water recycle function
4. Child lock function
(1) If you set child lock function, all the buttons will be locked including POWER. If the top lid
is opened while the washing machine is working, the washing will be stopped and the machine
will give an alarm. But if you can close the top lid in 5 seconds, the washing machine will stop alarm
and continue working. If you do not close the top lid in 5 seconds, the washing machine will
begin draining if there is water in the inner tub. Even closing the top lid will not work. During
the draining, the alarm will be given every 10 seconds. When the water in the inner tub is about
5cm higher, the alarm will be given every 10 minutes (alarm is always given). When the draining
is nished, the washing machine will be in the state of waiting. If the top lid is closed, the washing
machine is unlocked and start working as previous setting.
(2) Once child lock is set and the top lid is opened in 5 seconds during washing or rinse (there is water
in the inner tub), the washing machine will drain and give an alram. If you unlock the function during
draining, the washing machine will add water to setting water level and continue working.
If you set water recycle function, after the last rinse is nished, the washing machine will not
drain and spin. The SPIN and WATER RECYCLE indicator light will ash and an alarm will be given.
The washing machine will stop working (if nobody operates, the alarm will be given every 10 minutes and
in 1 hour, power supply will be cut off automatically). When you press START/PAUSE, the WATER RECYCLE
indicator light will turn on and the washing machine will begin to drain and spin. The user can reuse the water.