Decora Sunwood User manual

Sunwood 50mm Basswood- Solid Timber Venetian Blinds
A. Brackets should be placed at the
width of blinds headrail 6mm past each
end. The bracket doesn’t necessarily
need to touch the inside face of the
window frame.
B. Align the top of the centre support
bracket with the top of the mounting
bracket before installation. Install with
the bigger flap of the centre support
bracket on the top side and clear of the
slat ladder positions.
C. Push rail into brackets. Then press
gate to close brackets.
D. Screw valance clips onto back side
of the valance with screws provided
(Screw #3)
E. For Outside Mount: Screw one
end of the valance return clip onto the
valance using Screw #3. Align the edge
of the valance return with the valance.
Screw the other end of the valance clip
onto the valance return.
F. Hook valance clip with valance
attached onto the top of the headrail.
G. Always tilt blind horizontally before
raising/lowering to extend the life of
the blind. To lower blind: Move
cord to left pulling down gently until
cord lock releases.To raise blind: Pull
cord downward until blind reaches
desired height. To lock cords: Pull
cord right and release. Cord will lock
automatically.
Installing Hold Down Brackets
(Optional)
H. Hold down brackets: Using two
small screws, screw hold down bracket
to window facing or wall.
Snap bracket pin ends into the hole at
bottom rail end.
(Note: Centre support supplied for blind width 100cm or over)
WARNING
Children can be strangled in blind or drapery cords. To
keep cords out of reach of children, use these methods:
1. Clamp
2. Cleat
3. Tie the cord to itself
4. Tie-down device
Young children can strangle in the loop of
pull cords, chains, tapes that operate window
coverings. They can also wrap the cords around
their necks. To avoid the risk of strangulation
and entanglement, keep cords out of the
reach of young children. Move beds, cots and
furniture away from window covering cords.
child
safe
Metal tape
measure
Mounting
Bracket
Screw #1 Screw #2
Screw #3
Valance Clip
Valance Return
Clip
Cord Cleat Cord Cleat
Screw
Hold Down
Bracket
Centre Support
Pencil Drill Philips Head
Screwdriver
Step
Ladder
Drill Bit
(1/8" diameter)
WARNING
TOOLS RECOMMENDED FOR INSTALLATION:
MOUNTING HARDWARE MOUNTING INSTRUCTIONS
A
B
C
D
E
F
G
H
Headrail
Headrail
Gate
Outside Mount
Ceiling Mount
Inside Mount
Screw #1
Screw #3
Screw #3
Screw #3
Screw #2
Mounting Bracket
Mounting Bracket
Valance Clip
Valance
Valance
Valance
Return
Clip
Valance with Clip attached
Bottom
rail
Valance Return
Centre Support
Mounting
Bracket
Headrail
Tilt
Cord
Pull Cord

1. Install blind as directed
by manufacturer making
sure headrail is securely
fastened. Lower blind to
maximum desired length
and lock into place.
2. Measure the distance
from headrail to cord-stops.
If cord-stops are 2.5cm to
5cm below the headrail
no further adjustment is
needed. Your blind is ready
to be used.
3. If cord-stops ARE NOT
2.5cm to 5cm below
headrail loosed (but do not
untie) the knot surrounding
the cord-stop.
4. Push both the cord-stop
and the loosened knot
toward the headrail until
the cord-stop is 2.5cm to
5cm below the headrail.
Hold cord-stop in place and
pull firmly on lift cord to re-
tighten knot. Repeat steps
2, 3 & 4 for each cord-stop.
WARNING
Reduce risk of strangulation to infants and toddlers.
Position safety cord-stops before using blinds.
TO POSITION SAFETY CORD-STOPS:
(Note: Use of hold down bracket is recommended to fully utilise the safety
feature of the cord-stops)
1. When opening or closing blind only raise or lower the blind
when the slats are in the horizontal (open) position. Larger blinds
must be raised or lowered in stages. Raising or lowering in one
singular motion places excessive stress on the mechanism, strings
and brackets.Do not force the cord when tilting the blinds, this may
cause the mechanism to break.
2. It is not recommended that wooden blinds be fitted in damp or
wet environments as warpage may occur.
3. Dust blinds regularly.
4. If the blind becomes damp or wet, wipe down immediately.
The slats should be horizontal (open) and the blind released and
lowered completely. Allow to dry by removing the blinds from the
brackets and lay down on a hard surface. Do not place in direct
sunlight as excessive heat may cause the slats to warp. If the blinds
are excessively wet do not place the blinds on a surface that may
absorb any stain.
5. This wooden blind does not require any oiling.
If you have any doubts about the care or maintenance of your wood-
en blind do not hesitate to contact your nearest supplier for advice.
STEP 1
• Place safety cleat in the desired location on the wall and
mark the position of the two holes using a pencil.
• We recommend position the cleat to either side of the blind
and out of the reach of children
STEP 2
• Remove the safety cleat and drill the
position marked Once the holes are
drilled place a rawplug into the holes
• Use the screws provided to attach the
safety cleat to the wall
STEP 3
• We recommend that the cord is wrapped around the safety
cleat when the blind is not in use, as shown in the pictures
below.
Sunwood 50mm Basswood- Solid Timber Venetian Blinds
SAFETY CLEAT FITTING INSTRUCTIONS
RECOMMENDED CARE FOR WOODEN BLINDS
Headrail
Headrail
Cord-Stop
Cord-Stop
Cord-Stop
Headrail
2.5-5 cm
2.5-5cm