DEEP SEA ELECTRONICS DSEControl DSEM812 Setup guide

057-317 ISSUE:1.1
DEEP SEA ELECTRONICS
DSEM812 Installation and Operator Manual
Document Number: 057-317
Author: Anthony Manton

DSEM812 Installation and Operator Manual
057-317 ISSUE: 1.1
Page 2 of 50
Deep Sea Electronics Ltd
Highfield House
Hunmanby
North Yorkshire
YO14 0PH
ENGLAND
Sales Tel: [phone]
E-mail: [e-mail]
Website: www.deepseaelectronics.com
DSEM812 Installation and Operator Manual
© Deep Sea Electronics Ltd.
All rights reserved. No part of this publication may be reproduced in any material form (including
photocopying or storing in any medium by electronic means or other) without the written permission of
the copyright holder except in accordance with the provisions of the Copyright, Designs and Patents
Act 1988.
Applications for the copyright holder’s written permission to reproduce any part of this publication
must be addressed to Deep Sea Electronics Ltd at the address above.
The DSE logo and the name DSEControl®are UK registered trademarks of Deep Sea Electronics Ltd.
Any reference to trademarked product names used within this publication is owned by their respective
companies.
Deep Sea Electronics Ltd reserves the right to change the contents of this document without prior
notice.
Revision History
Issue No.
Comments
1
First Release
1.1
Updated dimension drawings

DSEM812 Installation and Operator Manual
Page 3 of 50
057-317 ISSUE: 1.1
TABLE OF CONTENTS
Section
Page
1Introduction ........................................................................................................5
1.1 CLARIFICATION OF NOTATION........................................................................................ 6
1.2 GLOSSARY OF TERMS.....................................................................................................6
1.3 RELATED INFORMATION.................................................................................................. 7
1.3.1 TECHNICAL INFORMATION........................................................................................7
1.4 SAFETY INSTRUCTIONS................................................................................................... 8
1.4.1 GENERAL....................................................................................................................8
1.4.2 INSTALLATION NOTES...............................................................................................8
2SPECIFICATIONS...............................................................................................9
2.1 PROCESSOR ..................................................................................................................... 9
2.2 MEMORY............................................................................................................................9
2.3 DC SUPPLY........................................................................................................................9
2.3.1 FUSING........................................................................................................................9
2.4 ENVIRONMENTAL ............................................................................................................. 9
2.5 USER INTERFACE........................................................................................................... 10
2.5.1 CONTROLS ............................................................................................................... 10
2.5.2 DISPLAY.................................................................................................................... 10
2.6 REAL TIME CLOCK.......................................................................................................... 10
2.7 INPUTS............................................................................................................................. 11
2.7.1 WAKE-UP................................................................................................................... 11
2.7.2 IGNITION(15)............................................................................................................. 12
2.7.3 PROGRAM ENABLE.................................................................................................. 13
2.7.4 DIGITAL INPUTS........................................................................................................ 13
2.7.4.1 DIGITAL.............................................................................................................. 13
2.7.4.2 FREQUENCY...................................................................................................... 13
2.7.5 ANALOGUE INPUTS.................................................................................................. 14
2.7.5.1 VOLTAGE ........................................................................................................... 14
2.7.5.2 CURRENT........................................................................................................... 14
2.7.5.3 RESISTIVE.......................................................................................................... 14
2.7.5.4 RATIOMETRIC.................................................................................................... 14
2.8 OUTPUTS......................................................................................................................... 15
2.8.1 VREF OUTPUT SUPPLY............................................................................................ 15
2.8.2 HIGH SIDE FIXED...................................................................................................... 15
2.8.3 LOW SIDE / HIGH SIDE CONFIGURABLE................................................................. 15
2.8.4 P.W.M. HIGH SIDE..................................................................................................... 15
2.9 COMMUNICATIONS......................................................................................................... 16
2.9.1 CAN ........................................................................................................................... 16
2.9.2 ETHERNET................................................................................................................ 16
2.9.3 WIFI ........................................................................................................................... 16
2.9.4 GPS ........................................................................................................................... 17
2.9.5 BLUETOOTH ............................................................................................................. 17
2.9.6 USB............................................................................................................................ 18
2.9.7 CAMERA INPUTS...................................................................................................... 19
2.9.8 IP CAMERAS............................................................................................................. 19
2.10 APPLICABLE STANDARDS ......................................................................................... 20
3INSTALLATION.................................................................................................21
3.1 DIMENSIONS AND MOUNTING ....................................................................................... 21
3.1.1 DIMENSIONS............................................................................................................. 21
3.1.2 FASCIA MOUNTING .................................................................................................. 22
3.1.2.1 PANEL CUTOUT................................................................................................. 22
3.1.2.2 MOUNTING OVERVIEW..................................................................................... 23
3.1.2.3 MOUNTING INSTRUCTIONS.............................................................................. 24
3.1.3 RAM MOUNTING....................................................................................................... 25
3.2 GROUNDING.................................................................................................................... 26

DSEM812 Installation and Operator Manual
057-317 ISSUE: 1.1
Page 4 of 50
3.3 FUSING............................................................................................................................. 26
3.4 TYPICAL CONNECTION DIAGRAM................................................................................. 27
3.5 USER CONNECTIONS ..................................................................................................... 28
3.5.1 CONNECTOR A (DC SUPPLY, CAN AND CAMERA)................................................. 29
3.5.2 CONNECTOR B (I/O)................................................................................................. 30
4OPERATION......................................................................................................31
4.1 NAVIGATION AND SELECTION....................................................................................... 31
4.2 SYSTEM PAGES.............................................................................................................. 31
4.3 RECOVERY...................................................................................................................... 33
4.4 CONFIGURATION............................................................................................................ 34
4.4.1 DEVICE INFORMATION............................................................................................. 34
4.4.1.1 VERSION INFORMATION................................................................................... 34
4.4.1.2 HARDWARE INFORMATION.............................................................................. 35
4.4.1.3 NETWORK INFORMATION................................................................................. 35
4.4.1.4 GPS INFORMATION........................................................................................... 37
4.4.1.5 DEVICE HISTORY .............................................................................................. 37
4.4.2 SETTINGS ................................................................................................................. 38
4.4.2.1 NETWORK SETTINGS........................................................................................ 38
4.4.2.2 DISPLAY BACKLIGHT ........................................................................................ 38
4.4.2.3 KEYBOARD BACKLIGHT.................................................................................... 39
4.4.2.4 REAL TIME CLOCK............................................................................................. 39
4.4.2.5 PASSWORD........................................................................................................ 39
4.4.2.6 IGNITION............................................................................................................ 39
4.4.3 CONTROL.................................................................................................................. 40
4.4.3.1 TEST................................................................................................................... 40
4.4.3.2 INSTALL.............................................................................................................. 42
4.4.3.3 FORMAT............................................................................................................. 43
4.4.3.4 CLONE................................................................................................................ 44
4.4.3.5 RESTORE........................................................................................................... 45
5CABLES, CONNECTORS, HARNESSES AND SPARE PARTS......................46
5.1 M812 CONNECTOR HARNESS KIT (016-185)................................................................. 47
6MAINTENANCE AND WARRANTY ..................................................................48
7DISPOSAL.........................................................................................................48
7.1 WEEE (WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT)................................... 48
8MISCELLANEOUS ............................................................................................ 48

Introduction
Page 5 of 50
057-317 ISSUE: 1.1
1 Introduction
This document details the Installation, Setup and Operation requirements of the DSEM812 Controller
and Display, part of the DSEControl®range of products.
The manual forms part of the product and should be kept for the entire life of the product. If the
product is passed or supplied to another party, ensure that this document is passed to them for
reference purposes.
This is not a controlled document. DSE do not automatically inform on updates. Any future updates of
this document are included on the DSE website at www.deepseaelectronics.com
Observe the operating instructions. Non-observance of the instructions, operation not in accordance
with use as prescribed below, wrong installation or incorrect handling seriously affects the safety of
the product, operators and machinery.
A robust metal case designed for chassis mounting houses the module. Connections are via locking
plug and sockets.
The controller is supplied with no application program. The equipment manufacturer is responsible for
creating and managing the application program and installing it in the controller. This is achieved
using CODESYS V3.5 or Qt programming depending upon product variant. Contact DSE Technical
Support for further details.
Variants of the device exist to provide an option with fascia mounted push buttons. All variants include
a capacitive touch screen.

Introduction
057-317 ISSUE: 1.1
Page 6 of 50
1.1 CLARIFICATION OF NOTATION
Clarification of notation used within this publication.
NOTE:
Highlights an essential element of a procedure to ensure correctness.
CAUTION!
Indicates a procedure or practice, which, if not strictly observed, could
result in damage or destruction of equipment.
WARNING!
Indicates a procedure or practice, which could result in injury to
personnel or loss of life if not followed correctly.
1.2 GLOSSARY OF TERMS
Term
Description
Application
The application is the program that allows the DSEM812 to control the
machine it is connected to.
The Application within the DSEM812 is designed and provided by the
manufacturer of the complete machine.
Bootloader
The Bootloader is the program within the DSEM812 responsible for loading
the Operating System.
CAN
Control Area Network. A high-speed data transmission system used
extensively within the Automotive and Off-Highway industries.
CODESYS
(Previously stylised
as CoDeSys)
Integrated Development Environment for programming controller
applications according to the international industrial standard IEC 61131-3.
DSEM812 supports CODESYS V3.5
ECU
Electronic Control Unit. For example,the DSEM812 device.
Firmware
The Firmware of the DSEM812 is the Operating System of the DSEM812
that reads and executes the Application program.
FSD
Full Scale Deflection. For example,0 mA to 20 mA is the Full Scale
Deflection of a current sink input.
I/O
Input / Output. For example,“The I/O is taken out to an external terminal
strip in the user panel”.
IDE
Integrated Development Environment. For example,the CODESYS V3.5
application that runs on the host PC is an IDE.
Ixyyy
An Input, where x is the connector and yyy is the input number. For
example,IC003 means Input 3 on Connector C.
PLC
Programmable Logic Controller. Industrial computer used primarily for the
automation of electromechanical machinery.
PWM
PWMi
A digital signal is used to represent an analogue value by using Pulse
Width Modulation. The mark-space ratio of a square wave changes to
represent the value.
Used for many control applications including proportional valves.
PWM= Voltage control.
PWMi = Current control.
Off-Highway
An industrial vehicle used primarily “off road”. For example,construction
and farm machinery. A wider interpretation includes on road access
platforms, emergency vehicles and other industrial machinery, used either
on the road, or off road.
Pin
A male or female pin connection in a housing (plug or socket).
Qxyyy
An Output, where x is the connector and yyy is the output number. For
example,QC002 means Output 2 on Connector C.

Introduction
Page 7 of 50
057-317 ISSUE: 1.1
1.3 RELATED INFORMATION
This document refers to and is referred by the following DSE publications which are obtained from the
DSE website: www.deepseaelectronics.com or by contacting DSE technical support: support@
deepseaelectronics.com.
1.3.1 TECHNICAL INFORMATION
DSE Part
Description
055-267
DSEM812 Datasheet
057-318
DSEM812 CODESYS Manual
057-319
DSEM812 Qt Manual

Introduction
057-317 ISSUE: 1.1
Page 8 of 50
1.4 SAFETY INSTRUCTIONS
1.4.1 GENERAL
•These instructions are for authorised persons according to the EMC and low-voltage directives.
The device must be installed, connected and put into operation by a qualified electrician.
•It is not permissible to open the controller or to modify or repair the controller. Modification or
repairs to the wiring could result in dangerous malfunctions. Repairs to the controller must be
performed by DSE. Contact your original equipment supplier in the case of malfunction.
•When the device is unpowered, ensure that no connection pins are connected to a voltage
source. Thus, when the supply is switched off, the supply for the electronics, the power outputs
and the external sensor supply must be switched off together.
•The controller heatsink at the rear heats up beyond normal ambient temperature during
operation. To avoid danger caused by high temperatures, protect against contact.
•The customer is responsible for performing risk analysis of the mobile working machine and
determining the possible safety related functions. The user is responsible for the safe function of
the application programs created. If necessary, they must additionally carry out an approval test
by corresponding supervisory and test organisations according to the national regulations.
•All connectors must be unplugged from the electronics during electrical welding and painting
operations.
1.4.2 INSTALLATION NOTES
•Follow the instructions of the connector manufacturer, specifically with respect to preventing
water from entering the device. See Section entitled Cables, Connectors, Harnesses and Spare
Parts for details of DSE Part Numbers.
•To maintain IP67 rating where connectors have unused pins, ensure the use of a suitable
Blanking Insert. In the case of a completely unused connector, the plug must be inserted, fully
populated with Pin Blanking Inserts. See Section entitled Cables, Connectors, Harnesses and
Spare Parts for details.
•M12 protection plugs (supplied) must be installed in both the USB and Ethernet interfaces to
ensure IP67 rating when the connectors are not in use. Tighten to 0.8 Nm (0.6 lbf ft). Where IP
protection is required when the interfaces are in use, suitable O-rings must be fitted. Silicon
grease to protect the O-rings is recommended.
•Ensure WiFi and GPS connectors are suitably protected if the device is not mounted within an
IP67 enclosure.
•The heatsink must be wired to vehicle ground to comply with EMC guidelines. A screw
connection point is provided for this purpose. A metallic screw must be used to create an
electrical connection to vehicle / machine ground.

Specifications
Page 9 of 50
057-317 ISSUE: 1.1
2 SPECIFICATIONS
2.1 PROCESSOR
Description
Specification
iMX6 Quad Microcontroller
ARM A9
Speed
1 GHz
2.2 MEMORY
Description
Specification
Flash
12.5 GB available for application.
16 GB total.
RAM
2 GB
2.3 DC SUPPLY
Description
Specification
Operating Voltage (Pin A7)
8 V to 32 V
Maximum Current (Full Backlight, no External Loads)
<1000 mA
Maximum Current (After Controlled Shutdown with Ignition off)
<50 mA
2.3.1 FUSING
Description
Specification
A1
ECU Supply
3 A Max
A2
Wake Up
1 A Max
A3
Ignition (15)
1 A Max
A6
Program Enable
1 A Max
B1
I/O Supply
8A or 16 A Max. See note above.
B9
I/O Supply
8 A or 16 A Max. See note above.
B10
VREF Auxiliary Supply Output
100 mA Max
2.4 ENVIRONMENTAL
NOTE: M12 protection plugs (supplied) must be installed in both the USB and Ethernet
interfaces to ensure IP67 rating when the connectors are not in use. Tighten to 0.8 Nm (0.6 lbf
ft). Where IP protection is required when the interfaces are in use, suitable O-rings must be
fitted.
Description
Specification
Operating Temperature
-20 ºC to +70 ºC
(-4 ºF to 158 ºF)
Storage Temperature
-30 ºC to +80 ºC
(-22 ºF to 176 ºF)
Degrees of Protection Provided by Enclosure
(With All Mating Connectors Fitted)
IP67
(NEMA 6)

Specifications
057-317 ISSUE: 1.1
Page 10 of 50
2.5 USER INTERFACE
2.5.1 CONTROLS
Description
Specification
Push Buttons DSEM812-01
0
Push Buttons DSEM812-02
16
2.5.2 DISPLAY
Description
Specification
Size (Across Diagonal)
30.7 mm
(12.1 ”)
Size (W x H)
1280 px X 800 px
Touchscreen
Capacitive
Aspect Ratio
16:10
Type
Optically Bonded LED
Lifetime
> 50,000 hours
Colour
24 bit
Splash Screen Image Type
Bitmap Image (BMP)
8 bit / 24 bit colour depth
1280 px X 800px
2.6 REAL TIME CLOCK
Description
Specification
Retention Type
Super Cap for up to 100 hours
Recharge Time
30 minutes
1280 px X 800 px
Capacitive
Touchscreen (all
variants)
16 X Surround Lit
Push Buttons
(DSEM812 Push
Button Variant
only)

Specifications
Page 11 of 50
057-317 ISSUE: 1.1
2.7 INPUTS
2.7.1 WAKE-UP
NOTE: Either Wake-Up OR Ignition initiates the start-up process. Both must be removed
to allow shutdown to commence.
NOTE: Ignition removal begins the Ignition timer after which the device powers down.
During this delay WakeUp functionality is disabled. Where the application requires WakeUp
functionality, it is recommended to keep Ignition timer to a minimum (minimum setting is 2
seconds).
With ECU power on, a +ve signal on A2 for at least one second initiates the start-up sequence. After
at least one second, the signal must be removed to prevent unintended start-ups following the next
shutdown.
After application of Wake-up (for more than one second), DSEM812 initiates the start -up process,
pausing, awaiting application of Ignition (pin A3). Subsequent application of Ignition allows for faster
start-up of the application given that the device is already ‘awake’, awaiting application of Ignition.
The Wake-up pin is intended to be driven by an external push button or signal from an external device
such as a vehicle door switch, remote control fob, schedule timer or a controlling PLC.
Description
Specification
Applicable Pin
Pin A2
Minimum Wake-Up Pin active time
1 second
Maximum Wake-Up Pin active time
Wake-Up must be removed before the shutdown
process is initiated. It’s recommended to make the
Wake-Up pulse 1.5 seconds to ensure it exceeds the
minimum requirement.

Specifications
057-317 ISSUE: 1.1
Page 12 of 50
2.7.2 IGNITION(15)
NOTE: Either Wake-Up OR Ignition initiates the start-up process. Both must be removed
to allow shutdown to commence.
NOTE: Application of Wake-up (Pin A2) wakens the device, allowing for faster application
start upon Ignition application.
NOTE: Ignition removal begins the Ignition Off timer after which the device powers down.
During this delay Wake Up functionality is disabled. Where the application requires Wake Up
functionality, it is recommended to keep Ignition timer to a minimum (minimum setting is 2
seconds).
NOTE: Ignition Off timer is available within System Pages. For further details, see section
System Pages | Configuration | Settings | Ignition elsewhere in this document.
With ECU power on, a +ve signal on A3 initiates the start-up sequence.
Removal of Ignition, for longer than the configurable timer, initiates shutdown (providing Wake-up is
already removed).
This pin is intended to be driven by an external ignition switch or a signal from an external device
such as a schedule timer or a controlling PLC.
Description
Specification
Applicable Pin
Pin A3
Time between removal and shutdown
Factory Setting 0 s.
For details of timer adjustment, see section System
Pages | Configuration | Settings | Ignition
elsewhere in this document.

Specifications
Page 13 of 50
057-317 ISSUE: 1.1
2.7.3 PROGRAM ENABLE
Program Enable is used to enter System Menu. See section entitled Operation elsewhere in this
document for details.
Description
Specification
Applicable Pin
Pin A6
2.7.4 DIGITAL INPUTS
2.7.4.1 DIGITAL
Description
Specification
Applicable Pins
Pins B13, B14, B17, B18, B21, B22
Minimum Voltage for High Level.
Configurable (Factory setting 6 V)
Maximum Voltage for Low Level
Configurable (Factory setting 2 V)
2.7.4.2 FREQUENCY
Description
Specification
Applicable Pins
Pins B13, B14, B17, B18, B21, B22
Frequency Range
5 Hz to 30 kHz
Resolution
100 Hz at Maximum Frequency
Accuracy
400 Hz at Maximum Frequency
Minimum Voltage For High Level (Mark)
>2 V
Maximum Voltage For Low Level (Space)
<1.4 V

Specifications
057-317 ISSUE: 1.1
Page 14 of 50
2.7.5 ANALOGUE INPUTS
2.7.5.1 VOLTAGE
Description
Specification
Applicable Pins
Pins B13, B14, B17, B18, B21, B22
Configurable Ranges
0 V to 5 V
0 V to 10 V
0 V to 32 V
Resolution
12 bits
Accuracy
± 2 % F.S.D.
Input Resistance
>=30 kΩ
Sampling Rate
2 mS
2.7.5.2 CURRENT
Description
Specification
Applicable Pins
Pins B13, B14, B17, B18, B21, B22
Configurable Ranges
0 mA to 20 mA
4 mA to 20 mA
Input Type
Current sink only
Input Sink Resistance
120 Ω± 1%
Sampling Rate
2 mS
Resolution
12 bits
Accuracy
± 1 % F.S.D.
2.7.5.3 RESISTIVE
Description
Specification
Applicable Pins
Pins B13, B14, B17, B18, B21, B22
Measurement Range
0 Ωto 3400 Ω
Measurement Source Voltage
12 V maximum
Measurement Source Current
1 mA
Sampling Rate
2 mS
Resolution
12 bits
Accuracy
± 1 % F.S.D.
2.7.5.4 RATIOMETRIC
Description
Specification
Applicable Pins
Pins B13, B14, B17, B18, B21, B22
Measurement Voltage Reference
Supply / VREF Output
Measurement Type
Ratio of input Pin to Supply
Measurement Source Current
1 mA
Accuracy
± 1 % F.S.D.

Specifications
Page 15 of 50
057-317 ISSUE: 1.1
2.8 OUTPUTS
2.8.1 VREF OUTPUT SUPPLY
Description
Specification
Applicable Pins
Pin B10
Voltage
Programmable 5 V / 10 V (±5 %)
Max Current
100 mA
2.8.2 HIGH SIDE FIXED
Description
Specification
Applicable Pins
Pins B2, B3
Maximum Current
2 A
Digital Output Active Low ‘ON’ State Maximum Voltage at
Rated Current
<2 V
Digital Output Active Low ‘OFF’ State Leakage Current
<10 mA at 24 V output supply
2.8.3 LOW SIDE / HIGH SIDE CONFIGURABLE
Description
Specification
Applicable Pins
Pins B6, B7, B19, B20
Maximum Current
2 A / 4 A Configurable
Digital Output Active Low ‘ON’ State Maximum Voltage at
Rated Current
<2 V
Digital Output Active Low ‘OFF’ State Leakage Current
<10 mA at 24 V output supply
2.8.4 P.W.M. HIGH SIDE
Description
Specification
Applicable Pins
Pins B2, B3
Maximum Current
2 A
Digital Output Active Low ‘ON’ State Maximum Voltage at
Rated Current
<2 V
Digital Output Active Low ‘OFF’ State Leakage Current
<10 mA at 24 V output supply
PWM Frequency
20 Hz to 250 Hz
Duty Cycle Resolution
0.1 %
Duty Cycle Precision
0.1 % (<=250 Hz), 1 % (>250 Hz)

Specifications
057-317 ISSUE: 1.1
Page 16 of 50
2.9 COMMUNICATIONS
2.9.1 CAN
NOTE: CAN connections are NOT internally terminated. A complete CAN network must
have 120 Ωterminators at each end of the network.
NOTE: Screened 120 impedance cable specified for use with CAN must be used for the
CAN links.
DSE stock and supply Belden cable 9841 which is a high quality 120 impedance cable
suitable for CAN use (DSE part number 016-030).
Description
Specification
Number of CAN Interfaces
3
Supported Protocols
J1939
CANopen
Raw CAN
Supported Baud Rates
10 kbit/s, 20 kbit/s, 50 kbit/s, 100 kbit/s, 125 kbit/s, 250 kbit/s,
500 kbit/s, 1 Mbit/s
2.9.2 ETHERNET
NOTE: DSE supply a cable suitable for ethernet connection. For further details, see
section entitled Cables, Connectors, Harnesses and Spare Parts elsewhere in this document.
Description
Specification
Number Of Ethernet Ports
2
Supported Data Rates
10 Mbit/s / 100 Mbit/s, Duplex
Supported Protocols
MODBUS TCP
CODESYS 3.5
M12 ‘D’ Coded – 4 Pin Female
Pin
Description
1
Tx+
2
RC+
3
TX-
4
RC-
2.9.3 WIFI
NOTE: Wifi provides a connection for other devices to join. For example, this allows a PC
to connect wirelessly to M812 for programming, diagnostics etc. It cannot be used to connect
to an existing network.
Description
Specification
WiFi Standards
IEEE 802.11 a/b/g/n/ac
WiFi Frequency
2.4 GHz
WiFi Antenna
External via SMA connector.

Specifications
Page 17 of 50
057-317 ISSUE: 1.1
2.9.4 GPS
NOTE: DSE supply an antenna suitable for GPS reception. For further details, see section
entitled Cables, Connectors, Harnesses and Spare Parts elsewhere in this document.
The device attains a GPS signal via an antenna. This provides stronger signal reception.
The GPS receiver allows the application program to retrieve the location of the device. Application
programming is required to achieve this.
Description
Specification
GPS Antenna
External via SMA connector.
GPS Antenna connector shown on the rear of DSEM812
2.9.5 BLUETOOTH
Bluetooth is not currently supported and is reserved for future use.
Description
Specification
Bluetooth Standard
4.1, supports BR, EDR, BLE

Specifications
057-317 ISSUE: 1.1
Page 18 of 50
2.9.6 USB
NOTE: DSE supply a cable suitable for USB connection. For further details, see section
entitled Cables, Connectors, Harnesses and Spare Parts elsewhere in this document.
Description
Specification
Number of USB Ports
1
USB Version
2
Supported Speeds
Full Speed (12 Mbit/s)
Device Class
08 (Mass Storage)
Max Size
64 Gb
Filing System
VFAT or FAT32
Filename Structure
Filenames must be alphanumeric only (A to Z, a to z, 0 to 9)
and “.” (used to seperate the file extension).
M12 ‘B’ Coded – 5 Pin Female
Pin
Description
1
5 V
2
Data -
3
Data +
4
0 V
5
Shield

Specifications
Page 19 of 50
057-317 ISSUE: 1.1
2.9.7 CAMERA INPUTS
NOTE: Cameras Inputs provide facility for viewing only. Logging to file is not supported.
Description
Specification
Number of Camera Inputs
4
Applicable Pins
A4, A5 (Camera 1)
A7, A8 (Camera 2)
A13, A14 (Camera 3)
A15, A23 (Camera 4)
Camera Type
VGA
Interface Type
Analogue (Composite) Video for PAL / NTSC
Overlay Size (when utilised)
1280 px X 800 px
2.9.8 IP CAMERAS
NOTE: IP Cameras provide facility for viewing only. Logging to file is not supported.
Description
Specification
Number of Supported IP Camera
4
Connection Method
Ethernet
Supported Protocols (RTP and RTSP)
H.264
MPEG-4

Specifications
057-317 ISSUE: 1.1
Page 20 of 50
2.10 APPLICABLE STANDARDS
Category
Description
Standard
CE marking
Electromagnetic compatibility (EMC) noise
immunity
Electromagnetic compatibility (EMC) emission
standard
Safety of information technology equipment,
general requirements
EN 61000-6-2
EN 61000-6-4
BS EN 60950-1: 2006
+ A2: 2013
E11 PENDING
EMC requirements for vehicles
Noise immunity with 100 V/m
UN/ECE-R10.05
ISO 11452-2
Climatic tests
Damp heat, cyclic upper temperature 55 ˚C
Damp heat, steady state test temperature 40 ˚C /
93% RH
Test duration: 21 days
Salt spray test severity level 3 (vehicle)
EN 60068-2-30
EN 60068-2-78
EN 60068-2-52
Mechanical tests
Test VII; vibration, random mounting location:
vehicle body. Vibration, sinusoidal
10...500 Hz; 0.73 mm / 10 g: 10 cycles / axis.
bumps 30 g / 6 ms; 24,000 shocks
ISO 16750-3
EN 60068-2-6
ISO 16750-3
Load Dump
151 V (Ri 1 Ω)
202 V (Ri 8 Ω)
ISO 16750-2