DekPro EFFEX User manual

Lighng Overview:
**See illustraon above as reference. Dashed lines are a representaon of approximate wire locaons, each installaon will vary.**
• Run wire from your transformer to the locaon of your rst post.
Note: Do not plug in transformer unl all wires are run.
• Wiring will go up the post to your rst lighng xture. Drill a minimum 1/2” hole through the deck board to allow passage
of the wiring through the board and into the post.
Tip: Laying post on its side prior to aaching to deck will allow for easier installaon of wire. Use a sh tape or equivalent
to pull wire to the top of the post. Tape wire to the top of post.
• Once wire is installed into rst post, stand the post upright and secure into place. (Plumb as necessary)
• From the rst lighng xture, run a 9’ Quick Connect Cable into the post and through the top rail to the next light.
Connue this method unl all lights are connected. (Brackets and posts need to be drilled to run wire)
Note: Wiring cannot be run through the top rail of stairs. For stairs, wiring should be run up the posts.
• Once lights are all connected, plug transformer into GFI protected 115V outlet and check to ensure all lights are illuminated,
if any lights have not illuminated unplug transformer and check connecons. Once all lights are working properly securely
aach caps to the post.
Components List:
A. Power Supply B. Wiring C. Post Cap
Deck Wiring Overview
DekPro™ EFFEX Low Voltage Lighng System
Installaon Guide
DekPro Manufacturing Inc. • P.O. Box 18566 • Minneapolis, MN 55418 • 1-855-433-5776
←
←
Quick
Connect
D
Post Cap
Wiring
Power Supply
Recessed Lights
Post Light
E
B
C
A
ꜜ
ꜜ
ꜜ
ꜜ
ꜜ
D. Post Light E. Stair Light

Outdoor
GFI Outlet
Timer / Photocell
Transformer
Dimmer
Output Wire
Output Wire
If not using Dimmer
connect Output Wire
directly to Transformer
LED DIMMER
+
_
+
_
Mode
(Includes Remote)
9’ Lead Wire
Post Cap
(Lighitng Fixture)
9’ Lead Wire
Post Cap
(Lighitng Fixture)
Connect to next
light fixture
Connect to next
light fixture
Lighng Components
DekPro™ EFFEX Low Voltage Lighng System
Installaon Guide
For full warranty coverage details visit www.dekpromfg.com
DekPro Manufacturing Inc. • P.O. Box 18566 • Minneapolis, MN 55418 • 1-855-433-5776
Wiring Post Cap
Run cable from the transformer up the rst post to
the post cap (left) and connect via Quick Connect
connections. From there, use a 9’ Quick Connect cable
to run through the top rail to the next post. Continue this
process until all post caps are connected. (Brackets and
posts will need to be drilled to accommodate cable)
Power Supply Diagram
←
←
←
←
←
←
←
←
←
. . . . . . . . . . . . . . . . . . . . . . . . . OR . . . . . . . . . . . . . . . . . . . . . . . . . . . .
←
←
←
*When using dimmer, ensure
all components are connected
before powering transformer*
Step 1
Ensure that all cable has
been properly installed
and test the lights before
mounting post cap to post.
Step 2
Fasten post cap to
the post using 2 each
screws included or use
silicone adhesive.
This guide represents the most common installaon method
for DekPro™ EFFEX lighng. More informaon can be found at our website
www.dekpromfg.com in regards to alternave wiring methods.
Quick
Connect
←
←