Dell emc Nx440 User instructions

Setting up Your Dell EMC NX440 System

WARNING: Before you set up and operate your Dell EMC NAS system,

read through the safety instructions that shipped with your system.

Dell EMC Software License Agreement

• Before using your system, read through the Dell EMC Software License

Agreement that shipped with the system.

• You must consider any media of Dell EMC installed software as backup

copies of the software installed on your system.

• If you do not accept the terms of agreement, see Dell.com/contactdell.

Documentation

For more information, go to:

• Dell.com/storagemanuals for documentation and information updates.

• Dell.com/support, type the Service Tag, and then click Submit.

Verifying package contents

Verify that all components listed on your packing slip are available.

Save all documentation and accessories.

Installing the system in a rack

This system requires a properly grounded electrical outlet, a compatible rack, and a

rack installation kit. For more information, see the section More information in this

document.

Locating your system Service Tag

• Your system is identified by a unique Express Service Code and Service Tag

number. Pull out the information tag at the front of the system to view the

Express Service Code and Service Tag.

• Alternatively, the information may be on a sticker on the chassis.

• This information is used by Dell EMC to route support calls to the appropriate

personnel.

NOTE: The illustrations in this document are not intended to represent a specific

NAS system.

Default password

The default password of the NAS system is Stor@ge!

Default system name

• Your system is configured with a default system name of D<ServiceTag>,

where <ServiceTag> is the Service Tag.

• To locate the Service Tag of your system, see the section Locating your system

Service Tag in this document.

1|Before you begin

2| Cabling the system using iSCSI

Turning on your storage array

You must rst turn on the storage arrays and additional expansion enclosures, if any. After the storage arrays and enclosures are initialized, turn on the Dell EMC

NX440 system.

Managing your NAS

To manage your NAS locally, connect a keyboard, monitor, and mouse directly to the NAS system.

To manage your NAS remotely, you can use:

• Remote desktop

NOTE: For more information about remote desktop, see the section Starting remote desktop in this document.

• iDRAC

NOTE: For information about initial setup, configuration, and console redirection using iDRAC, see the

Integrated Dell Remote Access Controller User’s

Guide

at Dell.com/idracmanuals.

Turning o your NAS system

To turn o your NAS system:

1. Close the application or the cluster.

2. Turn o the NAS system.

3. Turn o the storage devices.

4. Turn o the DAE (if any).

3| Turning on/off and managing your NAS system

For more information about Dell EMC NX series documentation, go to Dell.com/storagemanuals.

Always read the updates rst, because they often supersede information in other documents.

iSCSI/SAN switches Client switches

Dell EMC NX440 System Controller 0

External iSCSI (directly

connected to MD array)

Active directory server

connected to the network

Dell EMC NX440 system Controller 1

Storage Array

Network Cabling

SMB/NFS

NOTE: This figure is an example of cabling the Dell EMC NX440 systems with

the MD3XXX storage array. To connect other Dell EMC storage arrays to the

DellEMC NX440 system, see the documentation for the storage array.

Setting up Your Dell EMC NX440 System

(continued)

4|Initial conguration 5 |More information

1. When you start your NAS system that runs Windows Stor-

age Server 2016 for the rst time, on the Default Pass-

word page,

click OK.

NOTE: Before changing the password, make sure that

you change the system language according to your

preference.

2. To change your administrator password, press Ctrl+Alt+Del,

and then click Change a Password.

3. To change the default language, navigate to

C:\Dell_OEM\MUI and run the appropriate language

batch le. Complete the on-screen instructions to install

your preferred language.

Server Manager starts automatically when you log in the rst

time.

In Server Manager, click Congure this local server to:

• Change the computer name (if required)

• Add NAS system to the domain

• Check for latest Windows updates

• Specify the time zone

• Configure remote desktop

NOTE: To start a software system, on the taskbar,

click Start, and then click the program name.

Dell EMC OpenManage Server Administration

You can monitor your system remotely by using Dell EMC OpenManage Server Administrator. To access Dell EMC OpenManage Server Administrator, connect to the

secure port, 1311, of your NAS system. For example, type: https://D<ServiceTag>:1311, where

is Service Tag. To locate the Service Tag of your

system, see the section Locating your system Service Tag in this document.

Documentation

For more information, see the following documentation at Dell.com/storagemanuals.

Title Description

Getting Started Guide Provides an overview of system features, setting up your system, and technical specications. This document is also

shipped with your system.

Installation and Service Manual Provides information about system features and describes the system and installing or replacing system components.

Rack Installation Guide Describes the process of installing your system into a rack. This document is also shipped with your rack solution.

Administrator’s Guide Provides information about conguring and managing the system.

Troubleshooting Guide Provides information about troubleshooting the software and the system.

Dell EMC OpenManage Server

Administrator User’s Guide

Provides information about using the OpenManage Server Administrator to manage your Dell EMC system or NAS

system.

NOTE: For any documentation related to Dell EMC OpenManage Server Administrator, go to Dell.com/

openmanagemanuals.

Documentation feedback

You can rate the documentation or write your feedback on any of our Dell EMC Documentation pages and click Send Feedback to send your feedback.

2019 - 05

Rev. A00

Starting remote desktop

NOTE: Make sure that you have completed the Initial Conguration tasks before connecting to the NAS system using remote desktop.

• Enable remote desktop using Server Manager or system properties (Control Panel →System).

• If Dynamic Host Configuration Protocol (DHCP) and Domain Name System (DNS) are implemented on your network, your system automatically configures the

network settings. You can start remote desktop from a client and remotely access the NAS system using either the default system name or the IP address.