Dell PowerEdge C6145 User manual

Dell PowerEdge
C6145
Using the Baseboard
Management
Controller

___________
Information in this publication is subject to change without notice.
© 2011 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission
of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of
Dell Inc. Microsoft®and Windows®are registered trademarks of Microsoft Corporation.
Linux®is a registered trademark of Red Hat, Inc. in the United States and/or other
countries.
Other trademarks and trade names may be used in this publication to refer to either the
entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
June 2013 Rev. A01

Contents | 3
Contents
1 Introduction................................................................................5
BMC Key Features and Functions ............................................................5
2 Using the Web UI .......................................................................6
Logging in to the Web User Interface .......................................................6
Remote Management Controller GUI Explained .......................................8
Logout ......................................................................................................8
System Information...................................................................................8
Server Health .........................................................................................10
Configuration ..........................................................................................12
Remote Control ......................................................................................21
Maintenance...........................................................................................32
3 Sensors Threshold ..................................................................37

Contents | 4
4 Events Table.............................................................................40
5 IPMI 1.5 / 2.0 Command Support List .....................................44
6 IPMI OEM Command List.........................................................52
Extended Configurations ........................................................................61
Appendix ......................................................................................71
SSH/Telnet Enable and Disable .............................................................71
SSH/Telnet Redirect Enable and Disable ...............................................72
VLAN ID .................................................................................................73
BMC/BIOS Version Info ..........................................................................74

Introduction | 5
1
Introduction
This section introduces the BMC and includes the requirements for web-based
graphical user interface (GUI), keyboard, video, and mouse (KVM), and virtual
media.
BMC Key Features and Functions
The following lists the supported features of the BMC:
• Support for IPMI v1.5 and v2.0
• Out-of-band monitoring and control for sever management over LAN
• Dedicated 10/100 NIC for remote management over a network
• Information which includes main board part number, product name,
manufacturer, and so on.
• Health status/hardware monitoring report
• View and clear events log.
• Event notification using chassis LED indicator and Platform Event Trap
(PET)
• Platform Event Filtering (PEF) to take selected action for selected events,
including NMI and SMI
• Chassis management including power control and status report, front panel
buttons, LED control, Secure Mode, and Boot Option
• Watchdog and auto server re-start and recovery
• Multi-session user and alert destination for LAN channel
• IPMB connector to enable advanced server management communication
with BMC
• Support for APML v1.03

Using the WEB UI | 6
2
Using the Web UI
The BMC firmware features an embedded web server, enabling users to connect
to the BMC using an Internet browser (Microsoft Internet Explorer) without
needing to install KVM and virtual storage software on a remote console.
Web-based GUI is supported on the following browsers:
Microsoft Windows:
• Internet Explorer 6 or later
• Mozilla
®
Firefox
®
2.0017 or later
Linux :
Mozilla Firefox 2.0017 or later
NOTE: Before using the web user interface, ensure that the firewall settings are
configured to enable access to the following ports: 7578 (KVM),USB-CDROM:
5120, USB-FLOPPY: 5123.
Logging in to the Web User Interface
Enter the BMC-embedded server IP address or URL into the address bar of the
web browser. The BMC interface has a default of (DHCP\Static). Enter the
system BIOS setup with <F2> to change these settings.
When connecting to the BMC, the login screen prompts for the username and
password. This authentication with Secure Sockets Layer (SSL) protection
prevents unauthorized intruders from gaining access to the BMC web server.
Once authentication is passed, you can manage the server by privilege. At the
same time, the PHP Hypertext Preprocessor (PHP) records all user information,
including user ID and privilege.

Using the WEB UI | 7
Using Your Remote Management Controller:
The Remote Management Controller has a user-friendly Graphics User Interface
(GUI) called the Remote Management Controller GUI. It is designed to be easy
to use. It has a low learning curve because it uses a standard Internet browser.
Default User Name and Password
When you first try to access your Remote Management Controller, you are
prompted to enter a user name and password. Table 1-1 lists the user name and
password for logging on to the Remote Management Controller.
Table 2-1. BMC Default User Name and Password
Field
Default
User Name
Root
Password
Root
NOTE: The default user name and password are in lower-case characters.
NOTE: When you log in using the root user name and password, you have
administrative powers. Change your root password after logging in for the first
time.

Using the WEB UI | 8
Remote Management Controller GUI Explained
After you successfully log in to your Remote Management Controller, you are
greeted with the Remote Management Controller GUI.
Logout
Log out from your Remote Management Controller
The default timeout value is 30 seconds.
System Information
System Information
Click the System Information tab to view the Remote Management Controller.
The
System Information tab enables you to view the System Power Status,
firmware revision, aux firmware revision, and build time.
Table 2-2. BMC Information
BMC Information
Description
System Power Status
On or Off
Firmware Revision
Remote Management Controller firmware revision.
Aux Firmware
Revision
Remote Management Controller firmware
aux revision.
Build Time Date the firmware was last built in the form:
MM DD YYYY HH:MM:SS

Using the WEB UI | 9
List FRU
The List FRU page shows a list of the detected Field Replaceable Units (FRUs)
in the system. Select a FRU item from the drop down list to show more
information.
Chassis Information
Lists the Type, Part Number and the Serial Number of the FRU.
Board Information
Lists the Manufacturer, Product Name, Serial Number and Part Number.
Product Information
Lists the Manufacturer Name, Product Name, Serial Number, Version, and Part
Number.

Using the WEB UI | 10
Server Health
The Sensor menu provides information about system hardware such as the fan
speed, internal temperature, and voltage.
Sensor Readings & Sensor Readings with Thresholds
It reads the sensor information the system. You can select a sensor type
category . You can click “ Refresh ” to re-read the sensor state. And you can
click “
Show Thresholds ” to show the thresholds of every sensor.