Dell i1470-2932CRD - Inspiron 1470 Cherry User manual

Dell™Inspiron™1470/1570ServiceManual
Model P04F and P04G series
Type P04F001 and P04G001
Notes, Cautions, and Warnings
Information in this document is subject to change without notice.
©2009DellInc.Allrightsreserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and Inspiron are trademarks of Dell Inc.; Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell
under license; Microsoft,Windows, Windows Vista, and Windows Vista start button logo are either trademarks or registered trademarks of Microsoft Corporation in the United States
and/or other countries.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
August 2009 Rev. A00
Before You Begin
Battery
Optical Drive
Module Cover
Memory Module(s)
Wireless Mini-Card
Coin-Cell Battery
Power Button Cover
Keyboard
Palm Rest
Internal Card With Bluetooth®Wireless Technology
Hard Drive
USB/Audio Board
Speakers
Card Reader Board
System Board
Processor Heat Sink
Fan
Display
Camera
Flashing the BIOS
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

Back to Contents Page
Module Cover
Dell™Inspiron™1470/1570ServiceManual
Removing the Module Cover
Replacing the Module Cover




Removing the Module Cover

1. Follow the procedures in Before You Begin.

2. Remove the battery (see Removing the Battery).

3. Loosen the captive screw on the module cover.

4. Lift the module cover up at an angle to carefully disengage it from the computer base.
Replacing the Module Cover

1. Align the tabs on the module cover with the slots on the computer base and gently snap the cover into place.

2. Tighten the captive screw that secures the module cover to the computer base.

3. Replace the battery (see Replacing the Battery).
Back to Contents Page

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as the back panel) on the computer.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
NOTE: The location of the screw on the module cover may vary depending on the model of your computer.
1
module cover tabs (2)
2
module cover
3
captive screw



Back to Contents Page
Battery
Dell™Inspiron™1470/1570ServiceManual
Removing the Battery
Replacing the Battery




Removing the Battery

1. Follow the procedures in Before You Begin.

2. Turn the computer upside down on a clean, flat surface.

3. Slide and click the battery release latch.

4. Slide the battery out of the battery bay.
Replacing the Battery
Slide the battery into the battery bay until it clicks into place.
Back to Contents Page

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface.
CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for
other Dell computers.
1
battery release latch
2
battery
3
battery bay



Back to Contents Page
Before You Begin
Dell™Inspiron™1470/1570ServiceManual
Recommended Tools
Turning Off Your Computer
Before Working Inside Your Computer
This manual provides procedures for removing and installing components in your computer. Unless otherwise noted, each procedure assumes that the
following conditions exist:
lYou have performed the steps in Turning Off Your Computer and Before Working Inside Your Computer.
lYou have read the safety information that shipped with your computer.
lA component can be replaced or—if purchased separately—installed by performing the removal procedure in the reverse order.
Recommended Tools
The procedures in this document may require the following tools:
lPhillips screwdriver
lsmall flat-blade screwdriver
lplastic scribe
lBIOS executable update program available at support.dell.com
Turning Off Your Computer


1. Save and close all open files and exit all open programs.

2. In Windows Vista®, click ®®Shut Down.
In Windows®7, click ®Shut Down.
The computer turns off after the operating system shuts down.

3. Ensure that the computer is turned off. If your computer did not automatically turn off when you shut down the operating system, press and hold the
power button until it turns off.
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your own personal safety.






NOTE: This manual provides instructions for servicing the Inspiron 1470 and Inspiron 1570 computers. The majority of the instructions are the same for
both computers, however your model may vary slightly in appearance.
CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is
not covered by your warranty.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal
mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking
tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep
them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented
and aligned.


1. Ensure that the work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning Off Your Computer) and all attached devices.

3. If the computer is connected to a docking device (docked), undock it. See the documentation that came with your docking device for instructions.


4. Disconnect all telephone or network cables from the computer.

5. Eject any installed cards from the 7-in-1 memory card reader.

6. Disconnect your computer and all attached devices from their electrical outlets.

7. Disconnect all attached devices from your computer.


8. Remove the battery (see Removing the Battery).

9. Turn the computer top-side up, open it, and press the power button to ground the system board.
Back to Contents Page

CAUTION: To avoid damaging the computer, perform the following steps before you begin working inside the computer.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.

Back to Contents Page
Flashing the BIOS
Dell™Inspiron™1470/1570ServiceManual
To flash the BIOS, locate the latest BIOS update file for your computer at support.dell.com.

1. Ensure that the AC adapter is plugged in, the main battery is properly installed, and a network cable is attached.

2. Turn on the computer.

3. Go to support.dell.com.

4. Click Drivers & Downloads®Select Model.

5. Select the type of product in the Select Your Product Family list.

6. Select the product brand in the Select Your Product Line list.

7. Select the product model number in the Select Your Product Model list.

8. Click Confirm.

9. A list of results appear on the screen. Click BIOS.

10. Click Download Now to download the latest BIOS file.
The File Download window appears.

11. Click Save to save the file on your desktop. The file downloads to your desktop.

12. Click Close if the Download Complete window appears.
The file icon appears on your desktop and is titled the same as the downloaded BIOS update file.

13. Double-click the file icon on the desktop and follow the procedures on the screen.
Back to Contents Page

NOTE: If you have selected a different model and want to start over again, click Start Over on the top right of the menu.

Back to Contents Page
Internal Card With Bluetooth®Wireless Technology
Dell™Inspiron™1470/1570ServiceManual
Removing the Bluetooth Card
Replacing the Bluetooth Card




If you ordered a card with Bluetooth wireless technology with your computer, it is already installed.
Removing the Bluetooth Card

1. Follow the procedures in Before You Begin.

2. Remove the battery (see Removing the Battery).

3. Remove the optical drive (see Removing the Optical Drive).

4. Remove the module cover (see Removing the Module Cover).

5. Remove the Mini-Card (see Removing the Mini-Card).

6. Remove the power button cover (see Removing the Power Button Cover).

7. Remove the keyboard (see Removing the Keyboard).

8. Remove the palm rest (see Removing the Palm Rest).

9. Remove the screw from the Bluetooth card.

10. Lift the Bluetooth card to disconnect it from the USB/audio board.
Replacing the Bluetooth Card

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
screw
2
connector on the USB/audio board
3
Bluetooth card




1. Align the connector on the Bluetooth card with the connector on the USB/audio board and press down to connect the Bluetooth card to the USB/audio
board.

2. Replace the screw that secures the Bluetooth card to the USB/audio board.

3. Replace the palm rest (see Replacing the Palm Rest).

4. Replace the keyboard (see Replacing the Keyboard).

5. Replace the power button cover (see Replacing the Power Button Cover).

6. Replace the Mini-Card (see Replacing the Mini-Card).

7. Replace the module cover (see Replacing the Module Cover).

8. Replace the optical drive (see Replacing the Optical Drive).

9. Replace the battery (see Replacing the Battery).
Back to Contents Page


Back to Contents Page
Camera
Dell™Inspiron™1470/1570ServiceManual
Removing the Camera
Replacing the Camera




Removing the Camera

1. Follow the procedures in Before You Begin.

2. Remove the battery (see Removing the Battery).

3. Remove the display assembly (see Removing the Display Assembly).

4. Remove the display bezel (see Removing the Display Bezel).

5. Disconnect the camera cable from the camera module.

6. Pull up on the camera module to disconnect it from the display cover.
Replacing the Camera

1. Align the camera module using the alignment posts on the display cover.

2. Connect the camera cable to the camera module.

3. Replace the display bezel (see Replacing the Display Bezel).

4. Replace the display assembly (see Replacing the Display Assembly).
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on the back of the computer).
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
camera cable
2
camera cable connector
3
camera module
4
alignment posts (2)


5. Replace the battery (see Replacing the Battery).
Back to Contents Page


Back to Contents Page
Coin-Cell Battery
Dell™Inspiron™1470/1570ServiceManual
Removing the Coin-Cell Battery
Replacing the Coin-Cell Battery




Removing the Coin-Cell Battery

1. Follow the procedures in Before You Begin.

2. Remove the module cover (see Removing the Module Cover).

3. Disconnect the coin-cell battery cable and remove the coin-cell battery.
Replacing the Coin-Cell Battery

1. Connect the coin-cell battery cable to the connector on the system board.

2. Place the coin-cell battery between the two tabs on the computer base.

3. Replace the module cover (see Replacing the Module Cover).

4. Replace the battery (see Replacing the Battery).
Back to Contents Page

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
coin-cell battery
2
coin-cell battery cable
3
tabs (2)



Back to Contents Page
Processor Heat Sink
Dell™Inspiron™1470/1570ServiceManual
Removing the Processor Heat Sink
Replacing the Processor Heat Sink





Removing the Processor Heat Sink

1. Follow the procedures in Before You Begin.

2. Remove the battery (see Removing the Battery).

3. Remove the system board (see Removing the System Board) and turn it over.

4. In sequential order (indicated on the processor heat sink), loosen the six captive screws that secure the processor heat sink to the system board.

5. Lift the processor heat sink off the system board.
Replacing the Processor Heat Sink

1. Align the six captive screws on the processor heat sink with the system board and tighten the screws in descending order.

2. Replace the system board (see Replacing the System Board).

3. Replace the battery (see Replacing the Battery).
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
WARNING: If you remove the processor heat sink from the computer when the heat sink is hot, do not touch the metal housing of the processor
heat sink.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as the back panel) on the computer.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
processor heat sink
2
captive screws (6)
NOTE: The original thermal pad can be reused if the original processor and heat sink are reinstalled together. If either the processor or heat sink is
replaced, use the thermal pad provided in the kit to ensure that thermal conductivity is achieved.
NOTE: This procedure assumes that you have already removed the processor heat sink and are ready to replace it.

Back to Contents Page


Back to Contents Page
Card Reader Board
Dell™Inspiron™1470/1570ServiceManual
Removing the Card Reader Board
Replacing the Card Reader Board




Removing the Card Reader Board

1. Follow the procedures in Before You Begin.

2. Remove the battery (see Removing the Battery).

3. Remove the optical drive (see Removing the Optical Drive).

4. Remove the module cover (see Removing the Module Cover).

5. Remove the Mini-Card (see Removing the Mini-Card).

6. Remove the power button cover (see Removing the Power Button Cover).

7. Remove the keyboard (see Removing the Keyboard).

8. Remove the palm rest (see Removing the Palm Rest).

9. Remove the hard drive (Removing the Hard Drive).

10. Remove the left speaker (Removing the Speakers).

11. Disconnect the card reader cable from the from the connector on the system board.

12. Remove the screw that secures the card reader board to the computer base.

13. Lift the card reader board out of the computer base.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.

Replacing the Card Reader Board

1. Align the card reader board using the alignment posts on the computer base.

2. Replace the screw that secures the card reader board to the computer base.

3. Connect the card reader cable to the connector on the system board.

4. Replace the left speaker (see Replacing the Speakers).

5. Replace the hard drive (see Replacing the Hard Drive).

6. Replace the palm rest (see Replacing the Palm Rest).

7. Replace the keyboard (see Replacing the Keyboard).

8. Replace the power button cover (see Replacing the Power Button Cover).

9. Replace the Mini-Card (see Replacing the Mini-Card).

10. Replace the module cover (see Replacing the Module Cover).

11. Replace the optical drive (see Replacing the Optical Drive).

12. Replace the battery (see Replacing the Battery).
Back to Contents Page

1
screw
2
card reader cable
3
card reader board
4
alignment posts (2)

Back to Contents Page
Display
Dell™Inspiron™1470/1570ServiceManual
Display Assembly
Display Bezel
Display Panel and Cable




Display Assembly

Removing the Display Assembly

1. Follow the procedures in Before You Begin.

2. Remove the battery (see Removing the Battery).

3. Remove the module cover (see Removing the Module Cover).

4. Disconnect the antenna cables from the Mini-Card (see Removing the Mini-Card).

5. Remove the two screws on the base of the computer that secure the display assembly to the computer base.

6. Remove the power button cover (see Removing the Power Button Cover).

7. Remove the keyboard (see Removing the Keyboard).

8. Disconnect the display cable and remove the screw from the system board.

9. Pull the Mini-Card antenna cables up through the slot in the computer base.

10. Note the routing of all the cables and remove them from their routing guides.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.


11. Hold the display while you remove the three screws that secure the display assembly to the computer base.

12. Lift and remove the display assembly from the computer base.

Replacing the Display Assembly

1. Using the alignment posts, place the display assembly in position and replace the three screws that secure the display assembly to the computer base.

2. Route the Mini-Card antenna cables and display cable through their routing guides.

3. Route the antenna cables through the slot in the computer base.

4. Replace the screw and connect the display cable.

5. Replace the keyboard (see Replacing the Keyboard).

1
display cable connector
2
screw
3
display cable routing guides
4
display cable
5
Mini-Card antenna cables routing guides
6
slot in computer base

7
Mini-Card antenna cables


1
screws (3)
2
display assembly
3
alignment posts (2)



6. Replace the power button cover (see Replacing the Power Button Cover).

7. Replace the two screws on the base of the computer.

8. Connect the antenna cables from the Mini-Card (see Replacing the Mini-Card).

9. Replace the module cover (see Replacing the Module Cover).

10. Replace the battery (see Replacing the Battery).
Display Bezel

Removing the Display Bezel


1. Remove the display assembly (see Removing the Display Assembly).

2. Using your fingertips, carefully pry up the inside edge of the display bezel beginning with the bottom of the display bezel and working your way
counterclockwise around the display.

3. Remove the display bezel.

Replacing the Display Bezel

1. Place the curved part of the display bezel over the hinges and thread the cables through the left hinge.

2. Align the display bezel over the display panel, and gently snap the display bezel into place.

3. Replace the display assembly (see Replacing the Display Assembly).

4. Replace the battery (see Replacing the Battery).
CAUTION: The display bezel is extremely fragile. Be careful when removing it to prevent damaging the display bezel.
1
display bezel
1
curved part of the display bezel
2
cables
3
left hinge



Display Panel and Cable

Removing the Display Panel and Cable

1. Remove the display assembly (see Removing the Display Assembly).

2. Remove the display bezel (see Removing the Display Bezel).

3. Remove the four screws that secure the display panel to the display cover, and raise the display panel at a angle to access the display cable.

4. Pull up on the clear pull-tab to disconnect the display cable from the display panel.

5. Remove the display panel.

Replacing the Display Panel and Cable

1. Connect the display cable to the display panel.

2. Align the display panel using the alignment posts on the display cover.

3. Replace the four screws that secure the display panel to the display cover.

4. Replace the display bezel (see Replacing the Display Bezel).

5. Replace the display assembly (see Replacing the Display Assembly).

6. Replace the battery (see Replacing the Battery).
Back to Contents Page

1
screws (4)
2
display panel
3
display cover
4
alignment posts (4)
5
clear pull-tab
6
display cable

Back to Contents Page
Fan
Dell™Inspiron™1470/1570ServiceManual
Removing the Fan
Replacing the Fan




Removing the Fan

1. Follow the procedures in Before You Begin.

2. Remove the battery (see Removing the Battery).

3. Remove the system board (see Removing the System Board). You do not need to remove the processor heat sink from the system board.

4. Remove the two screws that secure the fan to the computer base.
Replacing the Fan

1. Place the fan on the computer base.

2. Replace the two screws that secure the fan to the computer base.

3. Replace the system board (see Replacing the System Board).

4. Replace the battery (see Replacing the Battery).
Back to Contents Page

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
computer base
2
screws (2)
3
fan

