Dell E228wfp User manual

Manuals

Documentation

Back to Contents Page

About Your Monitor

Dell™ E228WFP Flat Panel Monitor User's Guide

Front View

Back View

Bottom View

Side View

Monitor Specifications

Caring for your Monitor

Front View

1. Input source select button

2. OSD menu / select button

3. Brightness & Contrast / Down (-) button

4. Auto-adjust / Up (+) button

5. Power button (with power light indicator)

Back View

http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (1 of 8)8/28/2007 8:59:03 AM

Documentation

1 VESA mounting holes (100mm) (Behind

attached VESA plate) Use to mount the monitor with VESA compliance (100mm) bracket.

2 Barcode serial number label Refer to this label if you need to contact Dell for technical support.

3 Security lock slot Use a security lock with the slot to help secure your monitor.

4 Dell Soundbar mounting brackets Attach the optional Dell Soundbar.

5 Regulatory rating label List the regulatory approvals.

6 Stand removal button Press to release the stand from the monitor.

7 Cable management hole Help organize cables by placing them through the hole.

Bottom View

1 Power connector Insert the power cable.

2 DVI connector Connect your computer DVI cable.

3 VGA connector Connect your computer VGA cable.

Side View

http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (2 of 8)8/28/2007 8:59:03 AM

Documentation

Left side Right side

Monitor Specifications

Power Management Modes

If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. This is referred to as 'Power Save Mode'*. If input from keyboard, mouse, or other input devices is detected by the

computer, the monitor automatically 'wakes up'. The following table shows the power consumption and signaling of this automatic power saving feature:

VESA Modes Horizontal Sync Vertical Sync Video Power Indicator Power Consumption

Normal operation Active Active Active Green 45 W (typical)

Active-off mode Inactive Inactive Blanked Amber Less than 2 W

Switch off - - - Off Less than 1 W

NOTE: The OSD only functions in the 'normal operation' mode. One of the following messages appears when the “menu” or “plus” buttons are pressed

when in Active-off mode.

1. Analog Input

In Power Save Mode

Press Computer Power Button

or Any Key on Keyboard or Move Mouse

2. Digital Input

In Power Save Mode

Press Computer Power Button

or Any Key on Keyboard or Move Mouse

Activate the computer and 'wake up' the monitor to gain access to the OSD.

This monitor is ENERGY STAR-compliant as well as TCO '99 power management compatible.

http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (3 of 8)8/28/2007 8:59:03 AM

Documentation

* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.

Pin Assignments

15-pin D-Sub connector

Pin Number Monitor Side of the 15-pin Side Signal Cable

1 Video-Red

2 Video-Green

3 Video-Blue

4 GND

5 Self-test

6 GND-R

7 GND-G

8 GND-B

9 DDC +5V

10 GND-sync

11 GND

12 DDC data

13 H-sync

14 V-sync

15 DDC clock

24-pin Digital-Only DVI Connector

Note: Pin 1 is at the top right.

http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (4 of 8)8/28/2007 8:59:03 AM

Documentation

Pin Signal Assignment Pin Signal Assignment Pin Signal Assignment

1 T.M.D.S. Data 2- 9 T.M.D.S. Data 1- 17 T.M.D.S. Data 0-

2 T.M.D.S. Data 2+ 10 T.M.D.S. Data 1+ 18 T.M.D.S. Data 0+

3 T.M.D.S. Data 2 Shield 11 T.M.D.S. Data 1 Shield 19 T.M.D.S. Data 0 Shield

4 No Pin 12 No Pin 20 No Pin

5 No Pin 13 No Pin 21 No Pin

6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield

7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock +

8 No Connect 16 Hot Plug Detect 24 T.M.D.S. Clock -

Plug and Play Capability

You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so that the system can configure itself and optimize the

monitor settings. If desired, you can select different settings, but in most cases monitor installation is automatic.

General

Model number E228WFP

Screen type Active matrix - TFT LCD

Screen dimensions 22 inches (22-inch viewable image size)

Preset display area:

Horizontal 473.76 mm (18.65 inches)

Vertical 296.1 mm (11.66 inches)

Pixel pitch 0.282 mm

Viewing angle 160 (vertical) typ, 160 (horizontal) typ

Luminance output 300 CD/m (typ)

Contrast ratio 800 to 1 (typ)

Faceplate coating Antiglare with hard-coating 3H

Backlight CCFL edgelight system

Response Time 5ms typical

Resolution

Horizontal scan range 30 kHz to 83 kHz (automatic)

http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (5 of 8)8/28/2007 8:59:03 AM

Documentation

Vertical scan range 56 Hz to 75 Hz (automatic)

Optimal preset resolution 1680 x 1050 at 60 Hz

Highest preset resolution 1680 x 1050 at 60 Hz

Video display capabilities(DVI HD playback) 480p/576p/720p

Preset Display Modes

Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock

(MHz) Sync Polarity (Horizontal/

Vertical)

VESA, 720 x 400 31.5 70.0 28.3 -/+

VESA, 640 x 480 31.5 60.0 25.2 -/-

VESA, 640 x 480 37.5 75.0 31.5 -/-

VESA, 800 x 600 37.9 60.3 49.5 +/+

VESA, 800 x 600 46.9 75.0 49.5 +/+

VESA, 1024 x 768 48.4 60.0 65.0 -/-

VESA, 1024 x 768 60.0 75.0 78.8 +/+

VESA, 1152 x 864 67.5 75.0 108 +/+

VESA, 1280 x 1024 64.0 60.0 135.0 +/+

VESA, 1280 x 1024 80.0 75.0 135.0 +/+

VESA, 1680 x 1050 65.0 60.0 146.25 +/+

Electrical

Video input signals Analog RGB, 0.7 Volts +/-5%, positive polarity at 75 ohm input impedance

Digital DVI-D TMDS, 600mV for each differential line, positive polarity at 50 ohm input impedance with HDCP support

Synchronization input signals Separate horizontal and vertical synchronizations, polarity-free TTL level

AC input voltage / frequency / current 100 to 240 VAC / 50 or 60 Hz + 3 Hz / 1.5A

Inrush current 120V:30A (Max.)

240V:60A (Max.)

Physical Characteristics

Connector type 15-pin D-subminiature, blue connector; DVI-D, white connector

Signal cable type Digital: Detachable, DVI-D, Solid pins, shipped detached from the monitor

Analog: Detachable, D-Sub, 15pins, shipped attached to the monitor

Dimensions (with stand):

Height 16.10 inches (409.10 mm)

http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (6 of 8)8/28/2007 8:59:03 AM

Documentation

Width 20.12 inches (511.14 mm)

Depth 5.87 inches (149.16 mm)

Dimensions: (without stand)

Height 13.13 inches (333.54 mm)

Width 20.12 inches (511.14 mm)

Depth 2.56 inches (65.00 mm)

Stand dimensions:

Height 11.92 inches (302.83 mm)

Width 12.20 inches (309.93 mm)

Depth 5.90 inches (149.98 mm)

Weight with packaging 20.94 lbs (9.5 kg)

Weight with stand assembly and cables 15.65 lbs (7.1 kg)

Weight without stand assembly

(For wall mount or VESA mount considerations - no cables)

11.46 lbs (5.2 kg)

Weight of stand assembly 2.65 lbs (1.2 kg)

Environmental

Temperature:

Operating 5 to 35C (41 to 95F)

Nonoperating Storage: -20 to 60C (-4 to 140F)

Shipping: -20 to 60C(-4 to 140F)

Humidity:

Operating 10% to 80% (noncondensing)

Nonoperating Storage: 5% to 90% (noncondensing)

Shipping: 5% to 90%(noncondensing)

Altitude:

Operating 3,657.6m (12,000 ft) max

Nonoperating 12,192 m (40,000 ft) max

Thermal dissipation 256.08 BTU/hour (maximum)

119.5 BTU/hour (typical)

Caring for Your Monitor

CAUTION: Read and follow the safety instructions before cleaning the monitor.

CAUTION: Before cleaning the monitor, unplug the monitor power cable from the electrical outlet.

http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (7 of 8)8/28/2007 8:59:03 AM

Documentation

●To clean your antistatic screen, slightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.